Exterior Lighting

Adjustment

~4min read

ADJUSTMENT

PROCEDURE

1. PREPARE VEHICLE TO ADJUST FOG LIGHT AIM

(a) Prepare the vehicle:

  • Make sure that the vehicle body is not damaged or deformed around the fog lights.
  • Fill the fuel tank.
  • Make sure that the oil is at the specified level.
  • Make sure that the engine coolant is at the specified level.
  • Inflate the tires to the specified pressure.
  • Unload the luggage compartment and the vehicle, and check that the spare tire, tools and jack are in their original positions.
  • Bounce the vehicle at each corner to stabilize the suspension.
  • Have a person of average weight (75 kg, 165 lb.) sit in the driver's seat.

2. PREPARE VEHICLE TO ADJUST FOG LIGHT AIM

(a) Prepare the vehicle:

  • Position the vehicle in an area dark enough to easily observe the cutoff line. The cutoff line is a distinct line below which the light from the fog lights can be perceived and above which it cannot be perceived.
  • Position the vehicle at a 90° angle to the wall.
  • Keep a distance of 25 m (82 ft) between the vehicle (fog light center mark) and the wall.
  • Make sure that the vehicle is parked on a level surface.
  • Align the front wheels with the vehicle's centerline.
  • Shake the vehicle to stabilize the suspension.

NOTICE:

A distance of 25 m (82 ft) between the vehicle (fog light center mark) and the wall is required to correctly adjust the headlight aim. If this distance cannot be obtained, use a distance of exactly 3 m (9.84 ft) to inspect and adjust the fog light aim. (The size of the target area will change depending on the distance, so follow the instructions in the illustration.)

(b) Prepare a thick sheet of white paper (approximately 2 m (6.56 ft) (height) x 4 m (13.1 ft) (width)) to use as a screen.

(c) Draw a vertical line from top to bottom at the center of the screen (V line).

(d) Position the screen as shown in the illustration:

HINT:

  • Position the screen perpendicular to the floor.
  • Align the V line of the screen with the center of the vehicle.

(e) Draw the reference lines (H line, left V line and right V line) on the screen as shown in the illustration.

HINT:

Mark the fog light center marks on the screen.

(1) H line (fog light height):

Draw a horizontal line across the screen passing through the center marks. The H line should be at the same height as the fog light center marks.

(2) Left V line, right V line (left and right fog light center mark positions):

Draw 2 vertical lines crossing the H line at each of the center marks (aligned with the fog light center mark).

*a

Left V line

*b

V line

*c

Right V line

*d

H line

*e

Ground

3. INSPECT FOG LIGHT AIM

(a) Cover the fog light that is not being inspected or disconnect its connector so that the light it produces does not interfere with the aim inspection of the other light.

(b) Start the engine.

(c) Turn on the fog lights and check that the upper edge of the hot zone of each fog light matches the upper edge, as shown in the illustration:

HINT:

  • If the aiming distance is 25 m (82 ft):

    The upper edge of the hot zone must be 249 mm (9.80 in.) below the H line.

  • If the aiming distance is 3 m (9.84 ft):

    The upper edge of the hot zone must be 30 mm (1.18 in.) below the H line.

4. ADJUST FOG LIGHT AIM

(a) Remove the 2 screws and clip, and fold back the rear part of the front fender liner.

(b) Adjust the vertical headlight aim:

Using a screwdriver, adjust the aim of each fog light within the specified range by turning each adjusting screw.

NOTICE:

The final turn of the adjusting screw must be made clockwise. If the screw is overtightened, loosen it and then retighten it so that the final turn of the screw is clockwise.

HINT:

If the fog lights cannot be adjusted correctly, inspect the fog light assembly.

*a

Adjusting screw