DESCRIPTION
The main body ECU (multiplex network body ECU) receives headlight dimmer switch information signals and illuminates the high beam headlights.
WIRING DIAGRAM
NOTICE:
Inspect the fuses for circuits related to this system before performing the following procedure.
PROCEDURE
PERFORM ACTIVE TEST USING TECHSTREAM
(a) Using the Techstream, perform the Active Test.
Click here  Main Body
Tester Display | Test Part | Control Range | Diagnostic Note |
Head Light Hi |
Headlight dimmer relay (DIMMER) |
OFF or ON |
- |
OK:
Headlight dimmer relay (DIMMER) operates (high beam headlights turn on).
| OK |
 |
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
| NG |
 |
|
INSPECT HEADLIGHT DIMMER RELAY (DIMMER)
(a) Remove the headlight dimmer relay (DIMMER) from the engine room relay block and junction block.
(b) Inspect the headlight dimmer relay (DIMMER).
Click here 
| NG |
 |
REPLACE HEADLIGHT DIMMER RELAY (DIMMER) |
| OK |
 |
|
CHECK HARNESS AND CONNECTOR (HEADLIGHT DIMMER RELAY [DIMMER] - BATTERY)
(a) Remove the headlight dimmer relay (DIMMER) from the engine room relay block and junction block. |
 |
*a |
Front view of wire harness connector
(to Headlight Dimmer Relay [DIMMER]) |
|
|
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
Headlight dimmer relay (DIMMER) terminal 3 - Body ground |
Always |
11 to 14 V |
Headlight dimmer relay (DIMMER) terminal 1 - Body ground |
Always |
11 to 14 V |
| NG |
 |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
| OK |
 |
|
CHECK HARNESS AND CONNECTOR (HEADLIGHT DIMMER RELAY [DIMMER] - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND HEADLIGHT ASSEMBLY)
(a) Remove the headlight dimmer relay (DIMMER) from the engine room relay block and junction block.
(b) Disconnect the J165 main body ECU (multiplex network body ECU) connector.
(c) for Halogen Headlight:
(1) Disconnect the A8 headlight assembly LH connector.
(2) Disconnect the A9 headlight assembly RH connector.
(d) for LED Headlight:
(1) Disconnect the A59 headlight assembly LH connector.
(2) Disconnect the A58 headlight assembly RH connector.
(e) Measure the resistance according to the value(s) in the table below.
Standard Resistance: for Halogen Headlight
Tester Connection | Condition | Specified Condition |
Headlight dimmer relay (DIMMER) terminal 2 - J165-1 (DIM) |
Always |
Below 1 Ω |
Headlight dimmer relay (DIMMER) terminal 5 - A8-2 (HI) |
Always |
Below 1 Ω |
Headlight dimmer relay (DIMMER) terminal 2 or J165-1 (DIM) - Body ground |
Always |
10 kΩ or higher |
Headlight dimmer relay (DIMMER) terminal 5 or A8-2 (HI) - Body ground |
Always |
10 kΩ or higher |
for LED Headlight
Tester Connection | Condition | Specified Condition |
Headlight dimmer relay (DIMMER) terminal 2 - J165-1 (DIM) |
Always |
Below 1 Ω |
Headlight dimmer relay (DIMMER) terminal 5 - A59-1 (HI) |
Always |
Below 1 Ω |
Headlight dimmer relay (DIMMER) terminal 2 or J165-1 (DIM) - Body ground |
Always |
10 kΩ or higher |
Headlight dimmer relay (DIMMER) terminal 5 or A59-1 (HI) - Body ground |
Always |
10 kΩ or higher |
| OK |
 |
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
| NG |
 |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|