DESCRIPTION
The main body ECU (multiplex network body ECU) receives light control switch information signals and illuminates the low beam headlights.
WIRING DIAGRAM
NOTICE:
Inspect the bulbs and fuses for circuits related to this system before performing the following procedure.
PROCEDURE
PERFORM ACTIVE TEST USING TECHSTREAM
(a) Using the Techstream, perform the Active Test.
Click here  Main Body
Tester Display | Test Part | Control Range | Diagnostic Note |
Headlight |
Headlight relay (H-LP LO) |
OFF or ON |
- |
OK:
Headlight relay (H-LP LO) operates (low beam headlights turn on).
| OK |
 |
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
| NG |
 |
|
INSPECT HEADLIGHT RELAY (H-LP LO)
(a) Remove the headlight relay (H-LP LO) from the engine room relay block and junction block.
(b) Inspect the headlight relay (H-LP LO).
Click here 
| NG |
 |
REPLACE HEADLIGHT RELAY (H-LP LO) |
| OK |
 |
|
CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP LO] - BATTERY)
(a) Remove the headlight relay (H-LP LO) from the engine room relay block and junction block. |
 |
*a |
Front view of wire harness connector
(to Headlight Relay [H-LP LO]) |
|
|
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
Headlight relay (H-LP LO) terminal 3 - Body ground |
Always |
11 to 14 V |
Headlight relay terminal (H-LP LO) 1 - Body ground |
Always |
11 to 14 V |
| NG |
 |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
| OK |
 |
|
CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP LO] - DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND HEADLIGHT ASSEMBLY)
(a) Remove the headlight relay (H-LP LO) from the engine room relay block and junction block.
(b) Disconnect the 3H driver side junction block assembly connector.
(c) for Halogen Headlight:
(1) Disconnect the A8 headlight assembly LH connector.
(2) Disconnect the A9 headlight assembly RH connector.
(d) for LED Headlight:
(1) Disconnect the A59 headlight assembly LH connector.
(2) Disconnect the A58 headlight assembly RH connector.
(e) Measure the resistance according to the value(s) in the table below.
Standard Resistance: for Halogen Headlight
Tester Connection | Condition | Specified Condition |
Headlight relay (H-LP LO) terminal 2 - 3H-31 |
Always |
Below 1 Ω |
Headlight relay (H-LP LO) terminal 5 - A8-1 (LO) |
Always |
Below 1 Ω |
Headlight relay (H-LP LO) terminal 2 or 3H-31 - Body ground |
Always |
10 kΩ or higher |
Headlight relay (H-LP LO) terminal 5 or A8-1 (LO) - Body ground |
Always |
10 kΩ or higher |
for LED Headlight
Tester Connection | Condition | Specified Condition |
Headlight relay (H-LP LO) terminal 2 - 3H-31 |
Always |
Below 1 Ω |
Headlight relay (H-LP LO) terminal 5 - A59-2 (LO) |
Always |
Below 1 Ω |
Headlight relay (H-LP LO) terminal 2 or 3H-31 - Body ground |
Always |
10 kΩ or higher |
Headlight relay (H-LP LO) terminal 5 or A59-2 (LO) - Body ground |
Always |
10 kΩ or higher |
| NG |
 |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
| OK |
 |
|
CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY
(a) Remove the driver side junction block assembly.
Click here  |
 |
*a |
Component without harness connected
(Driver Side Junction Block Assembly) |
|
|
(b) Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly.
Click here 
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
A-15 (HRLY) - 3H-31 |
Always |
Below 1 Ω |
| OK |
 |
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
| NG |
 |
REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY |
|