DESCRIPTION
The automatic light control sensor detects ambient light. The sensor creates an electrical signal based on the amount of light detected, and sends the signal to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) turns on or off the headlights and taillights according to the signal.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
B1244 |
Light Sensor Circuit Malfunction |
Either of the following conditions is met:
- Malfunction in automatic light control sensor
- Open or short in automatic light control sensor circuit
|
- Harness or connector
- Automatic light control sensor
- Main body ECU (multiplex network body ECU)
|
WIRING DIAGRAM
PROCEDURE
CHECK FOR DTC
(a) Clear the DTCs.
Click here 
(b) Turn the ignition switch to ON.
(c) Turn on the headlights using the light control switch.
(d) Check for DTCs.
Click here 
OK:
DTC B1244 is not output.
| OK |
 |
USE SIMULATION METHOD TO CHECK |
| NG |
 |
|
READ VALUE USING TECHSTREAM
(a) Using the Techstream, read the Data List.
Click here 
(b) According to the display on the Techstream, read the Data List and check that the value of Light Sensor Illuminance changes while performing the following:
(1) Turn the light control switch to the AUTO position.
(2) Cover the automatic light control sensor with an opaque object.
(3) Slowly move the opaque object to uncover and then cover the automatic light control sensor. Main Body
Tester Display | Measurement Item / Range | Normal Condition | Diagnostic Note |
Light Sensor Illuminance |
Light control sensor illuminance / 0 to 8191 lx |
Value is output according to ambient light level |
- |
OK:
The value changes according to the amount the automatic light control sensor is covered.
| OK |
 |
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
| NG |
 |
|
CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - AUTOMATIC LIGHT CONTROL SENSOR)
(a) Disconnect the J165 main body ECU (multiplex network body ECU) connector.
(b) Disconnect the J176 automatic light control sensor connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
J165-19 (CLTB) - J176-1 (CLTB) |
Always |
Below 1 Ω |
J165-20 (CLTS) - J176-4 (CLTS) |
Always |
Below 1 Ω |
J165-21 (CLTE) - J176-2 (CLTE) |
Always |
Below 1 Ω |
J165-19 (CLTB) or J176-1 (CLTB) - Body ground |
Always |
10 kΩ or higher |
J165-20 (CLTS) or J176-4 (CLTS) - Body ground |
Always |
10 kΩ or higher |
J165-21 (CLTE) or J176-2 (CLTE) - Body ground |
Always |
10 kΩ or higher |
| NG |
 |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
| OK |
 |
|
CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
(a) Disconnect the J176 automatic light control sensor connector. |
 |
*a |
Component with harness connected
(Main Body ECU [Multiplex Network Body ECU]) |
|
|
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Switch Condition | Specified Condition |
J165-19 (CLTB) - J165-21 (CLTE) |
Ignition switch off |
Below 1 V |
Ignition switch ON |
11 to 14 V |
| NG |
 |
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
| OK |
 |
|
CHECK AUTOMATIC LIGHT CONTROL SENSOR
(a) Inspect the automatic light control sensor.
Click here 
| OK |
 |
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
| NG |
 |
REPLACE AUTOMATIC LIGHT CONTROL SENSOR |
|