Switches and sensors on the refrigerant circuit and associated connections
![]()
Note
For switching pressures, removing and installing switches, and switch location and design, see the vehicle-specific refrigerant circuit.
High-pressure switch for air conditioning -F23-
Function:
Switches the radiator fan to the next higher speed stage when the pressure in the refrigerant circuit rises (approx. 16 bar).

High-pressure switch for magnetic clutch -F118-
Function:
Switches off the A/C compressor when the pressure in the refrigerant circuit is too high (approx. 32 bar).

Low-pressure switch for air conditioning -F73-
Function:
Switches off the A/C compressor when the pressure in the refrigerant circuit drops (approx. 2 bar).

Connections with valve for switches on the refrigerant circuit
![]()
WARNING!
There is a risk of frostbite.
If the refrigerant circuit is not evacuated, refrigerant will escape.
The refrigerant must be recovered before removing valve -C-. If the refrigerant circuit is not opened within 10 minutes after recovery, pressure can build up in the refrigerant circuit due to residual evaporation. Recover the refrigerant again.
- Different threads for switches on the high-pressure and low-pressure sides.
- Only valves and O-rings that are resistant to refrigerant R134a and the associated refrigerant oils may be used.
- Connection (soldered in)
- O-ring
- Valve (with O-ring)

Pressure switch for air conditioning -F129-
This pressure switch has 3 functions:
1. Switches the radiator fan to the next higher speed stage when the pressure in the refrigerant circuit rises (approx. 16 bar).
2. If the pressure is too high (approx. 32 bar), switches off the air conditioning (e.g. due to insufficient engine cooling).
3. If the pressure is too low (approx. 2 bar), switches off the air conditioning (e.g. in case of refrigerant loss).
![]()
Note
The pressure switch for air conditioning -F129- replaces the high-pressure switch for air conditioning -F23-, the low-pressure switch for air conditioning -F73- and the high-pressure switch for magnetic clutch -F118-.

High-Pressure Sensor -G65-
This high-pressure sensor -G65- is installed in place of the pressure switch for air conditioning -F129-.
When voltage is applied, the high-pressure sensor generates a square-wave signal or a data telegram. This signal changes with the pressure in the system.
Using this signal, the downstream control units for the radiator fan, engine control unit, air conditioning operating and display unit Climatronic -E87- or Climatronic control unit -J255- etc. calculate the pressure in the refrigerant circuit and accordingly activate the radiator fan, the engine and the A/C magnetic clutch -N25-, or change the activation of the A/C compressor control valve -N280-.

Refrigerant pressure and refrigerant temperature sensor -G395-
![]()
WARNING!
There is a risk of frostbite.
If the refrigerant circuit is not evacuated, refrigerant will escape.
The refrigerant must be recovered before removing the refrigerant pressure and refrigerant temperature sensor -G395-. If the refrigerant circuit is not opened within 10 minutes after recovery, pressure can build up in the refrigerant circuit due to residual evaporation. Recover the refrigerant again.
This refrigerant pressure and refrigerant temperature sensor -G395- is installed in place of the high-pressure sensor -G65- or pressure switch for air conditioning -F129-.
The pressure signal is always queried, whereas the temperature signal is only queried at temperatures above 0 °C.
The Climatronic control unit -J255- works with this information and accordingly controls the radiator fan and the activation of the A/C compressor control valve -N280-.

A/C compressor control valve -N280-
The control valve is installed in the A/C compressor. It is activated by the air conditioning operating and display unit Climatronic -E87- or the Climatronic control unit -J255-. The control valve influences the pressure on the low-pressure side and thereby regulates the temperature in the evaporator.
![]()
Note
The A/C compressor control valve -N280- is part of the A/C compressor and cannot be replaced separately.
