Hyundai Accent Quiz
DOHC Engines

Poly-V belt

In this manual: DOHC Engines
Owner's Manual — 155SOHC Engines — 75DOHC Engines — 49Lubrication System — 14Cooling System — 23Emission Control — 3PCV Valve — 5Fuel system — 44Ignition System — 12Clutch — 17Manual transmission — 14Automatic transmission — 24Axle Shafts and Drive Shafts — 17Suspension — 31Steering — 45Brake System — 39Body — 23Air Conditioning System — 32Electrical Equipment — 54Appendix — 9Wiring Diagrams — 3
~2min read

Removal

PROCEDURE

1. Loosen the water pump pulley mounting bolts.
2. Loosen the alternator support nuts.
3. Loosen the alternator mounting bolt and remove the poly-V belt.

4. Выверните болты крепления шкива водяного насоса.

4. Remove the water pump pulley mounting bolts.

Tightening Torque:

Generator pivot bolt (A): 20–25 N·m Generator bolt (B): 15–22 N·m Generator bracket mounting bolt: 20–28 N·m

Inspection

Inspect the following items and replace them if defective.

PROCEDURE

1. Inspect the poly-V belt surface for damage and cracks.
2. Inspect the poly-V belt surface for oil and grease.
3. Inspect the poly-V belt surface for uneven wear.

4. Проверьте поверхность шкива на отсутствие трещин или повреждений.

4. Inspect the pulley surface for cracks or damage.

Installation

PROCEDURE

1. Install the pump pulley and secure it with the bolts.

2. Установите шкив насоса и закрепите его болтами.

2. Install the pump pulley and secure it with the bolts.

Poly-V Belt Tension Inspection and Adjustment

PROCEDURE

1. Check the condition of the poly-V belt and its routing on the pulleys.

Check that the ribs of the poly-V belt are correctly seated in the pulley grooves.

If the poly-V belt makes abnormal noise during operation, check the belt for wear and damage, as well as the pulley contact surfaces.

2. Специальным прибором измерьте натяжение ремня привода генератора. При отсутствии

2. Measure the alternator drive belt tension with a special tool. If the special tool is not available, check the belt tension by pressing on the belt with a force of 100 N (10 kg) at a point equidistant from the pulleys and measure the belt deflection.

Belt deflection for generator drive belt tension check:
New belt: 7.5–9.0 mm / 64–73 kg
Used belt: 9.0–10.4 mm / 39 kg
Check: 5.0–6.0 mm / 34–49 kg
Belt deflection for generator and power steering pump drive belt tension check:
New belt: 8 mm
Used belt: 6.0–7.0 mm
Belt deflection for generator and air conditioner drive belt tension check:
New belt: 6.0–9.0 mm
Used belt: 9.0–10.0 mm

Предупреждение

A used belt is a belt that has run on the engine for more than 5 min.

Measuring tension with a special tool

PROCEDURE

1. При измерении натяжения поликлинового ремня прибор не должен касаться других

1. When measuring the tension of the V-ribbed belt, the tool must not touch other engine components.
2. Adjust the deflection or tension of the power steering pump belt.
3. Tighten the adjusting bolt.
4. Turn the crankshaft several revolutions.

5. Проверьте натяжение ремня и, при необходимости, повторите регулировку.

5. Check the belt tension and, if necessary, repeat the adjustment.

Test yourself

A quick Hyundai Accent quiz: every answer comes with an explanation and a link to the manual page.