Heating,Ventilation And Air Conditioning

Components and Components Location. Auto Defogging Actuator Description and Operation

62steps
~372min
4/5difficulty
0102030405013.710N·mlb·ft
Tightening torque found on this page
Done 0 of 62

Contents:

Components and Components Location. Auto Defogging Actuator Description and Operation

Components and Components Location

Component

1. Driver's Side Seat Shower Duct
2. Driver's Side Mode Control Actuator
3. Driver's Side Temperature Control Actuator
4. Rear Heating Temperature Control actuator
5. Rear Cooling Temperature Control actuator
6. Passenger's Side Shower Duct
7. Passenger's Side Mode Condrol Actuator
8. Passenger's Side Temperature Control Actuator
9. Auto Defogging Actuator
10. Inner Condenser
11. PTC Heater
12. Heater Unit Lower Cover
13. Evaporator Core
14. Evaporator Temperature Sensor
15. Heater Module
16. Air Purification Unit

Auto Defogging Actuator Description and Operation

Description

That detects fogging with a auto defogging sensor and automatically operates the air conditioning system to prevent fogging.

Auto Defogging Actuator Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Remove the glove box housing. (Refer to Body - "Glove Box")
  2. Remove the auto defogging actuator.
    1. Disconnect the actuator connector (A).
    2. Remove the actuator (B) after removing the screws.

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Auto Defogging Actuator Inspection

Inspection

  1. Turn POWER OFF.
  2. Disconnect the auto defogging actuator connector. (Refer to Heater - "Auto Defogging Actuator")
  3. Connect the power ( + ) terminal to the 3 terminal of the auto defogging actuator connector and the (-) terminal to the 4 terminal and check whether the motor is running. When connected in the opposite direction, check if it operates in reverse.
    1. -
    2. -
    3. DEF (closed)
    4. DEF (open)
    5. Sensor Power (+5 V)
    6. Feedback Signal
    7. Sensor Ground
  4. Connect the auto defogging actuator connector.
  5. Turn POWER ON.
  6. Measure the terminal voltage between 5 and 6.
    Door Position Voltage (V) Error Detection
    DEF closed 0.5 ± 0.15 Low voltage : less than 0.1 V
    DEF open 4.5 ± 0.15 High voltage : more than 4.9 V

    * Feedback the current position of the actuator to the control.
  7. If the measured voltage does not match the specifications, replace it with a new auto defogging actuator.

Evaporator Core Removal and Installation

Removal

  1. Remove the heater unit. (Refer to Heater - "Heater Unit")
  2. Remove the inner condenser cover.
    1. Separate the evaporator temperature sensor (A).
    2. Remove the inner condenser cover (B) after removing the screws.
  3. Remove the heater unit lower cover (A) after removing the screws.
  4. Remove the evaporator core (A) in the direction of the arrow.

Installation

  1. Install in the reverse order of removal.

Heater Unit Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working a high voltage system, the technician must be observed and aware of "General Safety Information and Caution". If not, it may cause serious accidents such as electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Perform the high voltage shut off procedure. (Refer to General Information - "High Voltage Shut-off Procedures")
  2. Recover the refrigerant with Recovery/Recycling/Charging equipment. (Refer to Air conditioning System - "Refrigerant Recovery/Recycling/Charging/Vacuum/Leak Test")
  3. Remove the cowl cross bar assembly. (Refer to Body - "Cowl Cross Bar Assembly")
  4. Disconnect the expansion valve connector (A).
  5. Remove the suction & liquid tube assembly (A) after removing the bolts.

    Tightening torque : 8.8 - 13,7 N·m

    [Inner Conderser Side] [Evaporator Side]
  6. Separate the high voltage cable (A) after disconnecting the PTC heater high voltage cable connector (B).
  7. Disconnect the rear heating duct connector (A). [Driver Side] [Passenger Side]
  8. Remove the rear heating duct (A) after removing the nut.
    Tightening torque : 3.9 - 5,9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in)
    [Driver Side] [Passenger Side]
  9. Remove the heater unit (A) after removing the bolt.

    Tightening torque : 8.8 - 13,7 N·m

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working a high voltage system, the technician must be observed and aware of "General Safety Information and Caution". If not, it may cause serious accidents such as electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Mode Control Actuator Description and Operation

Description

  • It is operated by the auto temperature control unit and controls the position of the mode control door to adjust the wind direction mode.
  • It consists of an actuator motor that moves the mode door and a potentiometer that detects the position of the mode door. the wind direction mode in the order of Vent → Bi-Level → Floor → Mix

Mode Control Actuator Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Driver's Side Mode Control Actuator
  1. Remove the crash pad assembly. (Refer to Body - "Crash Pad Assembly")
  2. Remove the actuator (A) after removing the screws.
  3. Remove the steering column module (SCM). (Refer to Steering System - "Steering Column Module (SCM)")
  4. Remove the actuator.
    1. Disconnect the actuator connector (A).
    2. Remove the actuator (B) after removing the screws.
Passenger's Side Mode Control Actuator

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Mode Control Actuator Inspection

Inspection

  1. Turn POWER OFF.
  2. Disconnect the mode control actuator connector. (Refer to Heater - "Mode Control Actuator")
  3. Connect the power ( + ) terminal to the terminal 3 of the mode control actuator connector and the ( - ) terminal to the terminal 4 and check whether the motor operates. When connecting in the opposite direction, check if it operates in reverse. [Driver's Side]
    1. -
    2. -
    3. Defrost Mode
    4. Vent Mode
    5. Sensor Ground
    6. Feedback Signal
    7. Sensor Power (+5 V)

    [Passenger's Side]
    1. -
    2. -
    3. Vent Mode
    4. Defrost Mode
    5. Sensor Power (+5 V)
    6. Feedback Signal
    7. Sensor Ground
  4. Connect the mode control actuator connector.
  5. Turn POWER ON.
  6. Measure the terminal voltage. [Driver's seat] : between 7 - 6. [Passenger's seat] : between 5 - 6.
    Door Position Voltage (V) Error Detection
    Vent 0.5 ± 0.15 Low voltage : less than 0.1 V
    High voltage : more than 4.9 V
    Defrost 4.5 ± 0.15

    * Feedback the current position of the actuator to the control.
  7. If the measured voltage does not match with the specifications, replace it with a new mode control actuator.

PTC Heater Description and Operation

Description

  • The PTC (Positive Temperature Coefficient) heater is a device that is mounted on the rear side of the heater core and directly heats the air passing through the heater core to heat the room.
  • The PTC heater is an electric heating device using a PTC element as an auxiliary heating device to supplement the insufficient indoor heating heat source.

PTC Heater Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Perform the high voltage shut off procedure. (Refer to General Information - "High Voltage Shut-off Procedures")
  2. Remove the crash pad center panel. (Refer to Body - "Crash Pad Panel")
  3. Remove the front console cover. (Refer to Body - "Front Console Cover")
  4. Disconnect the passenger's side duct sensor connector (A).
  5. Remove the passenger's side shower duct (A) after removing the screw.
  6. Separate the high voltage cable (A) after disconnecting the PTC heater high voltage cable connector (B).
  7. Remove the clips (A).
    Clip position :
  8. Separate PTC heater signal wiring (B) after disconnecting the connector (A).
  9. Disconnect the PTC heater ground wire (A) after removing the bolt.

    Tightening torque : 10.8 - 13,7 N·m

  10. Remove the PTC heater (A) after removing the screws.

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working a high voltage system, the technician must be observed and aware of "General Safety Information and Caution". If not, it may cause serious accidents such as electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

PTC Heater Inspection

Inspection

  1. Check if there is an output signal (actuation request) from the A/C controller.
  2. Inspect the interlock with a KDS to see if there is a problem.
  3. Check that low voltage (12.0 V) is supplied.
  4. For inspection, refer to the pin information below. [Main Power Connector]
    Pin Number Function
    1 High voltage ( + )
    2 High voltage ( - )
    3 Interlock ( + )
    4 Interlock ( - )

    [Signal Connector]
    Pin Number Function
    1 IG 3
    2 CAN HIGH
    3 CAN LOW
    4 Interlock ( + )
    5 Interlock ( - )
    6 Ground

Temperature Control Actuator Description and Operation

Description

It is operated by the auto temperature control unit and controls the position of the temperature control door to adjust the temperature of the discharge air.

Temperature Control Actuator Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Driver's Side Temperature Control Actuator
  1. Remove the crash pad lower panel. (Refer to Body - "Crash Pad Panel")
  2. Disconnect the driver's side duct sensor connector (A).
  3. Remove the driver's side shower duct (A) after removing the screw.
  4. Remove the actuator.
    1. Disconnect the actuator connector (A).
    2. Remove the actuator (B) after removing the screws.
  5. Remove the glove box housing. (Refer to Body - "Glove Box")
  6. Remove the actuator.
    1. Disconnect the actuator connector (A).
    2. Remove the actuator (B) after removing the screws.
  7. Remove the cowl cross bar assembly. (Refer to Body - "Cowl Cross Bar Assembly")
  8. Remove the rear cooling actuator (A) and the rear heating actuator (B) after removing the screws.
Passenger's Side Temperature Control Actuator Rear Temperature Control Actuator

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Temperature Control Actuator Inspection

Inspection

  1. Turn POWER OFF.
  2. Disconnect the temperature control actuator connector. (Refer to Heater - "Temperature Control Actuator")
  3. Connect the power ( + ) terminal to the 3 terminal of the actuator connector and the ( - ) terminal to the 4 terminal and check whether the actuator is running. When connected in the opposite direction, check if it operates in reverse. [Driver's Side]
    1. -
    2. -
    3. Cooling
    4. Heating
    5. Sensor Power (+5 V)
    6. Feedback Signal
    7. Sensor Ground

    [Passenger's Side]
    1. -
    2. -
    3. Heating
    4. Cooling
    5. Sensor Ground
    6. Feedback Signal
    7. Sensor Power (+5 V)

    [Rear Cooling]
    1. -
    2. -
    3. Cooling Open
    4. Cooling Closed
    5. Sensor Ground
    6. Feedback Signal
    7. Sensor Power (+5 V)

    [Rear Heating]
    1. -
    2. -
    3. Heating Open
    4. Heating Closed
    5. Sensor Ground
    6. Feedback Signal
    7. Sensor Power (+5 V)
  4. Connect the temperature control actuator connector.
  5. Turn POWER ON.
  6. Measure the terminal voltage. [Driver's seat] : between 6 and 5. [Passenger's seat], [Rear cooling], [Rear heating] : between 7 and 6.
    Door Position Voltage (V) Error Detection
    Maximum cooling 0.5 ± 0.15 Low voltage : less than 0.1 V
    High voltage : more than 4.9 V
    Maximum heating 4.5 ± 0.15

    * Feedback the current position of the actuator to the control.
  7. If the measured voltage does not match with the specifications, replace it with a new temperature control actuator.