Battery Control System (Standard)
High Voltage Distributing System
In this manual: Battery Control System (Standard)
56steps
~336min
4/5difficulty
Done 0 of 56
Contents:
Components and Components Location
Component
[2WD]
| 1. Front High Voltage Junction Box 1-a. 4.9 - 7,8 N·m (0.5 - 0.8 kgf·m, 3.6 - 5.8 lb·ft, 43.4 - 69.4 lb·ft) 2. High Voltage Junction Box Service Cover 2-a. 3.9 - 5,9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in) 2-b. 6.9 - 9,8 N·m |
3. Rear High Voltage Junction Box 3-a. 15.7 - 24 N·m 3-b. 17.7 - 26 N·m |
[4WD]
| 1. High Voltage Junction Box Service Cover 1-a. 3.9 - 5,9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in) 1-b. 6.9 - 9,8 N·m 2. Front High Voltage Junction Box 2-a. 6.9 - 9,8 N·m |
3. High Voltage Junction Box Service Cover 3-a. 3.9 - 5,9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in) 3-b. 6.9 - 9,8 N·m 4. Rear High Voltage Junction Box 4-a. 15.7 - 24 N·m 4-b. 17.7 - 26 N·m |
Front High Voltage Junction Box Description and Operation
Description
2WD- It works as the power distributor for connecting the high voltage battery power and high voltage components (A/C compressor, PTC heater, etc.).
- It is installed in front cross member and includes bus bar, fuse and PTC relay ( + ).
NO System Possible Cause 1 Battery signal - 2 Battery PTC relay BMU relay control 3 Battery PTC fuse 20 A 4 PTC heater fuse 30 A 5 A/C compressor fuse 30 A
- It is the role of power distributor for connecting the high voltage battery power and front high voltage components (Inverter, A/C compressor, PTC heater, etc.).
- It is installed in front inverter assembly and includes bus bar and quick charge relay (+, -).
NO System Possible Cause 1 Battery PTC relay BMU relay control 2 PTC heater fuse 30 A 3 Battery PTC fuse 20 A 4 A/C compressor fuse 30 A
Front High Voltage Junction Box Removal and Installation - 2WD
Removal
|
- Perform the high voltage shut off procedure. (Refer to Battery Control System - “High Voltage Shut-off Procedure”)
- Remove the front trunk. (Refer to Body - "Front Trunk")
- Remove the low voltage (12 V) battery tray. (Refer to Electric Power Conversion System - "low voltage (12 V) battery")
- Disconnect the front junction box connector (A).
- Disconnect the high voltage power cable (A) and battery heater connector (B).
- Disconnect the PTC heater connector (A).
- Disconnect the electric A/C compressor (A).
- Remove the front high voltage junction box (A) after removing the nuts.
Tightening torque : 6.9 - 9,8 N·m
Installation
|
- Install in the reverse order of removal.
- Install the front high voltage junction box to the specified torque.
- If front high voltage junction box is dropped, it may cause internal damage. (Do not reuse)
Front High Voltage Junction Box Removal and Installation - 4WD
Removal
|
- Perform the high voltage shut off procedure. (Refer to Battery Control System - “High Voltage Shut-off Procedure”)
- Separate the power cable fastener (A) from the body frame.
- Remove the front trunk. (Refer to Body - "Front Trunk")
- Disconnect the PTC heater connector (A) and battery heater connector (B).
- Disconnect the high voltage junction box signal connector (A, B).
- Separate the wiring protector (A) after removing the bolts.
Tightening torque : 6.9 - 9,8 N·m
- Remove the high voltage junction box service cover (A).
Tightening torque : 3.9 - 5,9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in) - Remove the high voltage junction box ground bolts (A).
Tightening torque : 6.9 - 9,8 N·m
- Separate the Electric A/C compressor connector (A) and fastener (B).
- Separate the power cable after separating the fasteners (A).
- Remove the front high voltage junction box (A).
Tightening torque : 6.9 - 9,8 N·m
Installation
|
- Perform the PE system leak test with the KDS. (Refer to Front High Voltage Junction Box - "Air Tightness")
- Install in the reverse order of removal.
- Install the front high voltage junction box to the specified torque.
- If front high voltage junction box is dropped, it may cause internal damage. (Do not reuse)
Front High Voltage Junction Box Air Tightness Inspection
Special Service Tool
| Tool Name | Illustration | Description |
| EV battery pack Inspecting for air tightness tool GIT air tightness test equipment |
Used for inspecting the air tightness of the Battery System Assembly (BSA) and PE system |
Air Tightness Inspection
|
- Disconnect the PTC heater connector (A) and battery heater connector (B).
- Install the battery heater sealing connector (P008) (A).
- Install the PTC heater sealing connector (P001) (A).
- Disconnect the high voltage junction box connector (A).
- Install the high voltage junction box sealing connector (P006) (A).
- Disconnect the electric A/C compressor (A).
- Install the Electric A/C compressor sealing connector (P007) (A).
- Remove the front rear under cover. (Refer to Motor and Reduction Gear System - "Front Under Cover")
- Install the sealing connector (P003) (A) in the high voltage cable.
- Install the pressure regulator adapters (A) in the pressure regulator.
- Maintain the pressure by pushing the adapter with hands until starting to inspect, when installing the pressure regulator adapter.
- Be careful not to bend the EV battery pack inspection tool hose and the pressure regulator adapter hose.
- Perform the PE system leak test with the KDS. (S/W Management → Motor Control Unit → PE System leak test)
Refer to the KDS screen for operating conditions and details. - Check the PE system leakage.
Judgment standard for PE system leakage PASS FAIL
Power Cable Components and Components Location
Component Location
2WD
| 1. Power Cable [front high voltage junction box ↔ Battery System Assembly (BSA)] 3. Charger Inlet Assembly |
2. Power Cable [Integrated Charging Control Unit (ICCU) ↔ BSA] |
4WD
| 1. Power Cable [front high voltage junction box ↔ Battery System Assembly (BSA)] 3. Charger Inlet Assembly |
2. Power Cable [Integrated Charging Control Unit (ICCU) ↔ BSA] |
Power Cable Removal and Installation - 2WD
Removal
|
- Perform the high voltage shut off procedure. (Refer to Battery Control System - “High Voltage Shut-off Procedure”)
- Remove the front under cover. (Refer to Motor and Reduction Gear System - "Front Under Cover")
- Disconnect the power cable connector (A) on the front high voltage junction box side.
- Perform the high voltage shut off procedure. (Refer to Battery Control System - “High Voltage Shut-off Procedure”)
- Remove the rear seat assembly. (Refer to Body - "Rear Seat Assembly")
- Disconnect the Integrated Charge Control Unit (ICCU) connector (A).
- Remove the rear under cover. (Refer to Motor and Reduction Gear System - "Rear Under Cover")
- Separate the cable (A) from the body by disconnecting the ICCU connector.
Installation
|
- Install in the reverse order of removal.
If power cable is dropped, it may cause internal damage. (Do not reuse)
Power Cable Removal and Installation - 4WD
Removal
|
- Remove the front high voltage junction box. (Refer to High Voltage Distributing System - "Front High Voltage Junction Box")
It cannot separate the power cable individually due to integrated with the front high voltage junction box. - Perform the high voltage shut off procedure. (Refer to Battery Control System - “High Voltage Shut-off Procedure”)
- Remove the rear seat assembly. (Refer to Body - "Rear Seat Assembly")
- Disconnect the Integrated Charge Control Unit (ICCU) connector (A).
- Remove the rear under cover. (Refer to Motor and Reduction Gear System - "Rear Under Cover")
- Separate the cable (A) from the body by disconnecting the ICCU connector.
Installation
|
- Install in the reverse order of removal.
If power cable is dropped, it may cause internal damage. (Do not reuse)
Rear High Voltage Junction Box Description and Operation
Description
- It works as the power distributor that connects high voltage battery power to rear high voltage components.
- It is installed on the top of the rear wheel motor and the front of the multi-inverter assembly, and has a built-in bus bar and fast charging relays (+, -).
NO System Possible Cause 1 Quick Charge Relay ( + ) BMU relay control 2 Quick Charge Relay ( - )
Rear High Voltage Junction Box Removal and Installation
Removal
|
- Perform the high voltage shut off procedure. (Refer to Battery Control System - “High Voltage Shut-off Procedure”)
- Remove the rear cross member under cover. (Refer to Motor and Reduction Gear System - "Rear Under Cover")
- Remove the rear high voltage junction box bolt (A).
Tightening torque : 15.7 - 24 N·m
- Remove the rear motor and reduction gear assembly. (Refer to Motor and Reduction Gear System - "Rear Motor and Reduction Gear Assembly")
- Disconnect the rear high voltage junction box connector (A).
- Separate the high voltage cable (A) from the body after removing the bolts.
Tightening torque : 15.7 - 24 N·m
- Remove the high voltage junction box service cover (A).
Tightening torque : 3.9 - 5,9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in) - Remove the rear high voltage junction box and inverter bolts (A).
Tightening torque : 6.9 - 9,8 N·m
- Remove the rear high voltage junction box (A) after removing the bolts and nut.
Tightening torque Bolt : 15.7 - 24 N·m Nut : 17.7 - 26 N·m
Installation
|
- Install in the reverse order of removal.
- Install the rear high voltage junction box to the specified torque.
- If rear high voltage junction box is dropped, it may cause internal damage. (Do not reuse)
Was this page helpful?