Battery Control System (Standard)

Electric Power Conversion System

56steps
~336min
4/5difficulty
010203040509.87N·mlb·ft
Tightening torque found on this page
Done 0 of 56

Contents:

Components and Components Location

Component

[2WD]

1. Integrated Charging Control Unit (ICCU) 2. Multi Inverter Assembly

[4WD]

1. Integrated Charging Control Unit (ICCU)
2. Multi Inverter Assembly
3. Inverter Assembly

Description and Operation

Description

Definition
  • The electric power conversion system is a system that converts power, whether external or internal, from the vehicle depending on the purpose for which it is used.
  • The electric power conversion system converts to power for driving a motor by using the battery power from the vehicle. It also representatively consists of inverter and converter.
  • It converts more than one of the voltage, current frequency or phrase without loss of power.
Composition Inverter
  • The inverter converts the DC power of the high voltage battery in the vehicle to the AC power for driving the motor.
  • The power is converted by MOSFET power module installed into the inverter, the MOSFET module is switching by control signal.
  • The single phase power is converted to 3 phases and supplies the power for rotating a motor.
  • Both EV and HEV is applied the voltage to the driving motor through the reverse conversion in the case of driving in EV mode through power conversion. (A reverse conversion device : it is to convert the DC power of the high voltage to the AC power for driving the motor.)
  • The inverter can both funcion for forward and reverse.
[Inverter power conversion flow chart] Converter

AC/DC Converter

  • When the vehicle decelerates or brakes, the drive motor becomes a generator and generates power. The generated power is converted to power for charging the high voltage battery again.
  • The AC/DC converter is also used to charge the vehicle. When the vehicle charges outside, the high voltage battery is charged by the converted voltage by converting the On-Board Charger (OBC) installed into the Integrated Charging Control Unit (ICCU) converts the AC to DC.

DC/DC converter inside the Low Voltage DC Converter (LDC)

  • The Low DC/DC Converter (LDC) charges the low voltage (12 V) battery by converting the voltage to a low voltage. It also supplies the auxiliary power by reducing the voltage to 12 V supplied by the high voltage battery.
  • The LDC consists of a switching part, a transform part for transforming the power, and a rectifier part. The switching part converts power, and the transform part reduces the voltage. After this, the rectifier rectifies the voltage and output 12 V to the battery.
    Switching : the input power, whether AC or DC, converts to the output power that is required through switching.

DC/DC converter inside the On-Board Charger(OBC)

  • The OBC consists of the AC/DC and DC/DC converters; the AC/DC converter is made of an EMI filter and a PFC converter.
    • EMI Filter : It is a filter for remove the high frequency noise caused by input voltage.
    • PFC Converter : It is a converter used to compensate for power factor when converting AC voltage to DC voltage.
  • The DC/DC converter in the OBC is converted to DC by the AC/DC converter when charging the battery, and it controls the output voltage of the high voltage battery through the DC/DC converter in the OBC.
  • When using the 220 V installing the V2L connector to the charging port or through the interior V2L connector, the AC/DC converter and DC/DC converter in OBC can convert power to bidirectional.

Battery (12 V) Specification

Specification

Item Specification
Type eAGM60L-DIN
Capacity [20HR/5HR] (AH) 60 / 48
Cold cranking amperage (A) 500
Reserve capacity (Min) 100
Specific gravity 1.30 - 1.32 [25 °C]
Voltage (V) 12

Battery Size
Type Width Length Height Total Height
mm (in.)
eAGM60L-DIN 239 - 243 (9.40 - 9.56) 173 - 175 (6.81 - 6.89) 164.5 - 167.5 (6.48 - 6.60) 187 - 190 (7.36 - 7.48)

Battery (12 V) Components and Components Location

Component

1. Low Voltage (12 V) Battery Negative ( - ) Cable
1-a. 7.8 - 9,8 N·m
2. Low Voltage (12 V) Battery Positive ( + ) Cable
2-a. 7.8 - 9,8 N·m
3. Battery Clamp
3-a. 9.8 - 13,7 N·m
4. Low Voltage (12 V) Battery
5. Vehicle Control Unit (VCU)
5-a. 9.8 - 11,8 N·m
6. Battery Tray
6-a. 9.8 - 13,7 N·m

Battery (12 V) Description and Operation

Description

  • The low voltage (12 V) battery supplies power to electronic components excluding high voltage components.
  • The high voltage of a high voltage battery is converted into a low voltage (DC 12 V) through the LDC to charge the low voltage (12 V) battery.

Battery Label Information

  1. Battery specifications
    • AGM : Absorbent Glass Material
    • CMF : Closed Maintenance Free
    • MF : Maintenance Free
  2. Battery capacity (20 Ah)
  3. Terminal location
    • L : battery positive ( + ) terminal on the left.
    • R : battery positive ( + ) terminal on the right.
  4. Battery type
    • BCI (Battery Council International) : Intruding terminal
    • DIN (Deutsche Industric Normen) : Recessed terminal
  5. Cold Cranking Ampere (CCA)
    CCA : The amount of current that can be supplied for 30 seconds while maintaining a voltage of more than 7.2 V at -18°C (-0.4°F).
  6. Part number
  7. Reserve Capacity (RC)
    RC : The amount of time that can be supplied 25 A while maintaining the minimum voltage of 10.5 V at 27 °C.

Battery (12 V) Removal and Installation - 2WD

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Low voltage (12 V) battery
  1. Open the front trunk (A).
  2. Open the service cover (A).
  3. Disconnect the low voltage (12 V) battery negative ( - ) terminal (A).

    Tightening torque : 7.8 - 9,8 N·m

  4. Disconnect the service interlock connector (A).
    Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
    The service interlock connector cannot be completely removed.
  5. Open the low voltage (12 V) battery positive ( + ) terminal cover (A).
  6. Disconnect the low voltage (12 V) battery positive ( + ) terminal (A).

    Tightening torque : 7.8 - 9,8 N·m

  7. Remove the low voltage (12 V) battery (A) after removing the clamp (B).

    Tightening torque : 9.8 - 13,7 N·m

  8. Remove the low voltage (12 V) battery. (Refer to low voltage (12 V) battery - "Removal and Installation - 2WD")
  9. Remove the Vehicle Control Unit (VCU). (Refer to Motor & Reduction Gear System - "Vehicle Control Unit (VCU)")
  10. Separate the wiring (A) from the tray.
  11. Remove the low voltage (12 V) battery tray (A).

    Tightening torque : 9.8 - 13,7 N·m

Low Voltage (12 V) Battery Tray

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.
    • Install the low voltage (12 V) battery and the tray to the specified torque.
    • If the low voltage (12 V) battery is dropped, it may cause internal damage. (Do not reuse)
    • When installing the low voltage (12 V) battery, install the clamp correctly.
    • When replacing the low voltage (12 V) battery, be sure to replace it with the same specification(capacity, manufacturer, etc.) as the battery installed originally. When the different specification is installed, it may be determined that the battery performance is abnormal by the battery sensor.

Battery (12 V) Removal and Installation - 4WD

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Low Voltage (12 V) Battery
  1. Open the front trunk (A).
  2. Open the service cover (A).
  3. Disconnect the low voltage (12 V) battery negative ( - ) terminal (A).

    Tightening torque : 7.8 - 9,8 N·m

  4. Disconnect the service interlock connector (A).
    Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
    The service interlock connector cannot be completely removed.
  5. Open the low voltage (12 V) battery positive ( + ) terminal cover (A).
  6. Disconnect the low voltage (12 V) battery positive ( + ) terminal (A).

    Tightening torque : 7.8 - 9,8 N·m

  7. Remove the low voltage (12 V) battery (A) after removing the clamp (B).

    Tightening torque : 9.8 - 13,7 N·m

  8. Remove the low voltage (12 V) battery. (Refer to low voltage (12 V) battery - "Removal and Installation - 4WD")
  9. Remove the Vehicle Control Unit (VCU). (Refer to Motor & Reduction Gear System - "Vehicle Control Unit (VCU)")
  10. Separate the wiring (A, B) from the tray.
  11. Remove the auxiliary 12 V battery tray (A).

    Tightening torque : 9.8 - 13,7 N·m

Low Voltage (12 V) Battery Tray

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.
    • Install the low voltage (12 V) battery and the tray to the specified torque.
    • If the low voltage (12 V) battery is dropped, it may cause internal damage. (Do not reuse)
    • When installing the low voltage (12 V) battery, install the clamp correctly.
    • When replacing the low voltage (12 V) battery, be sure to replace it with the same specification(capacity, manufacturer, etc.) as the battery installed originally. When the different specification is installed, it may be determined that the battery performance is abnormal by the battery sensor.

Battery Sensor Specification. Battery Sensor Components and Components Location

Battery Sensor Specification

Specification

Item Specification
Rated voltage (V) 12 - 14
Operating voltage (V) 6 - 18
Operating temperature [°C (°F)] -40 to 105 (-40 to 221)
Parasitic current (uA) Maximum 300

Battery Sensor Components and Components Location

Component

1. Battery Sensor Connector 2. Battery Sensor
2-a. 7.8 - 9,8 N·m
2-b. 26.5 - 32 N·m

Battery Sensor Description and Operation

Description

  • The battery sensor is installed on the low voltage (12 V) battery negative ( - ) terminal and is also known as Intelligent Battery Sensor (IBS).
  • The IBS continuously monitors the State of Charge (SOC) of the battery to maintain a consistent level of charge.
  • It manages the battery system to use the battery in optimal condition, predicts battery replacement, and detects troubled batteries in advance.
  • It detects the voltage change supplied to the electric actuator and the input and output currents of the low voltage (12 V) battery.
  • If the battery voltage is more than reference by checking the SOC after 30 minutes after POWER OFF when the air conditioning system is turned on for more than 5 minutes during the driving, the data is used as a reference signal provided to DATC for activating the after-blow function.
  • It operates in whole Network (CAN) Sleep Mode by the signal detected by the IBS, for cutting the power in the vehicle and preventing the discharging the battery due to the parasitics current blocking system in the power domain controller.
  • It is used as a signal to send the battery voltage to the Vehicle Control Unit (VCU) through the power domain controller. After judging the possibility of charging in VCU, the low voltage (12 V) battery is charged by LDC.

Battery Sensor Removal and Installation - 2WD

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Disconnect the service interlock connector (A).
    Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
    The service interlock connector cannot be completely removed.
  2. Remove the front trunk. (Refer to Body - "Front Trunk")
  3. Disconnect the low voltage (12 V) battery negative ( - ) terminal (A).

    Tightening torque : 7.8 - 9,8 N·m

  4. Disconnect the battery sensor connector (A).
  5. Remove the battery sensor (A) after removing the bolt.

    Tightening torque : 26.5 - 32 N·m

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.
    • Install the battery sensor to the specified torque.
    • If the battery sensor is dropped, it may cause internal damage. (Do not reuse)

Battery Sensor Removal and Installation - 4WD

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Disconnect the service interlock connector (A).
    Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
    The service interlock connector cannot be completely removed.
  2. Remove the front trunk. (Refer to Body - "Front Trunk")
  3. Disconnect the low voltage (12 V) battery negative ( - ) terminal (A).

    Tightening torque : 7.8 - 9,8 N·m

  4. Disconnect the battery sensor connector (A).
  5. Remove the battery sensor (A) after removing the bolt.

    Tightening torque : 26.5 - 32 N·m

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.
    • Install the battery sensor to the specified torque.
    • If the battery sensor is dropped, it may cause internal damage. (Do not reuse)

Inverter Assembly (4WD) Specification. Inverter Assembly (4WD) Components and Components Location

Inverter Assembly (4WD) Specification

Specification

Item Specification
Input voltage (V) 452.5 - 778.3
Operating voltage (V) 9 - 16
Continuous current (A) 75 (@20 min.)
Maximum ampere (A) 190 (@15 sec.)

Inverter Assembly (4WD) Components and Components Location

Component

1. High Voltage Junction Box Service Cover
1-a. 3.9 - 5,9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in)
2. Front High Voltage Junction Box
2-a. 6.9 - 9,8 N·m
2-b. 6.9 - 9,8 N·m
3. Inverter Assembly
3-a. 3.9 - 5,9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in)

Inverter Assembly (4WD) Description and Operation

Description

  • The inverter assembly is installed in the front motor and converts the DC power to AC power (variable frequency, variable voltage).
  • It controls the rotational speed and torque of the motor through the power control.
  • In the PE (Power Electric) system based on the E-GMP platform, the front motor is configured with an integrated inverter and reducer.
  • It controls to maximize both the rotation speed of the drive motor by power module in the inverter and the charge amount of high voltage while the regenerative braking.

Inverter Assembly (4WD) Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Drain the motor coolant. (Refer to Cooling System - "Motor Coolant")
  2. Remove the front high voltage junction box. (Refer to High Voltage Distributing System - "Front High Voltage Junction Box")
  3. Separate the inverter cooling quick connector hose (A).
  4. Remove the inverter assembly (A) after removing the bolts.
    Tightening torque : 3.9 - 5,9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in)

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.
    • Install the inverter assembly to the specified torque.
    • If inverter assembly is dropped, it may cause internal damage. (Do not reuse)
    • Replace the gasket (A) and check the installation before installing the inverter assembly.
  2. Perform the PE system leak test with the KDS. (Refer to High Voltage Distributing System - "Front High Voltage Junction Box")
  3. Fill the motor coolant. (Refer to Cooling System - "Coolant")
  4. Perform the Initialization of Automatic Resolver Offset Calibration procedures with the KDS. (S/W Management → Front Motor Control Unit (MCU) → Initialization of Automatic Resolver Offset Calibration)
    Refer to the KDS screen for operating conditions and details.

Low Voltage DC/DC Converter (LDC) Description and Operation

Description

  • There are the high voltage and low voltage (12 V) battery to supply and store the power related with driving an EV. The low voltage (12 V) battery that is as to power device supplied to electric devices and control units in the vehicle is required to extra charging device.
  • If the battery state of charge (SOC) is detected by the battery sensor, it is input into the Vehicle Control Unit (VCU) through the power domain controller. The VCU judges the charging possibility and charges the low voltage (12 V) battery through the cooperative control Battery Management Unit (BMU) and Integrated Charge Control Unit (ICCU) by operating the IG3 relay when charging is necessary. In addition, the related control units are activated.
  • If the low voltage (12 V) battery's voltage does not exceed the reference, the Low DC/DC Converter (LDC) lowers the high voltage to the voltage for charging the low voltage (12 V) battery and charges it. (High voltage DC → Low voltage DC)
  • The low voltage (12 V) battery charging stops when it exceeds the reference value by operating the burst mode on LDC to improve battery efficiency.
  • It has to monitoring the SOC of the low voltage (12 V) battery to control the LDC through the battery sensor. If the SOC is less than the reference value, the charging starts and maximum 90%.
  • The LDC is integrated with the On-Board Charger (OBC) in the Integrated Charge Control Unit (ICCU). [The flowchart when charge the low voltage (12 V) battery by Low DC/DC Converter (LDC)]
    When the low voltage (12 V) battery is not charged
    • When the lever is not P
    • When the trunk is open
    • When the SOC of a high voltage battery is less than 35%
    • When the battery sensor or electric devices has trouble

Low Voltage DC/DC Converter (LDC) Troubleshooting

Troubleshooting

How to remedy when the fault code occurs

Item Major Fault Code Suspected Cause Inspection
Low Voltage DC/DC Converter (LDC) inspection • Output overvoltage fault • LDC • Replace the Integrated Charge Control Unit (ICCU) when the same problem occurs after the vehicle restarts
• LDC voltage control fault
• Sensors fault
- Current sensor offset calibration abnormality
- Temperature sensor open circuit/short circuit/performance abnormality fault
- Input / Output voltage sensor fault
• PWM output fault
Vehicle inspection • Output terminal path fault • Wiring and connectors between the LDC output terminal and the high voltage junction box • Check the LDC output circuit and cable connection condition
Coolant system fault • Coolant system
• Low coolant
• Electric Water Pump (EWP)
• Inspect the EWP
• Input over current fault • low voltage (12 V) battery discharged
• 12 V electric component overload
• Check the low voltage (12 V) battery discharge condition
• Check abnormal operation or short circuit conditions of 12 V electric components

Low Voltage DC/DC Converter (LDC) Replacement. Multi Inverter Assembly Specification

Low Voltage DC/DC Converter (LDC) Replacement

Replacement

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
The Low Voltage DC/DC Converter (LDC) cannot be replaced individually due to included in the Integrated Charging Control Unit (ICCU). If necessary, replace the ICCU.
  1. Replace the Integrated Charge Control Unit (ICCU). (Refer to High Voltage Charging System - "Integrated Charger and Converter Unit (ICCU)")

Multi Inverter Assembly Specification

Specification

Item Specification
Input voltage (V) 452.5 - 778.3
Operating voltage (V) 9 - 16
Continuous current (A) 180 (@20 min.)
Maximum ampere (A) 245 (@15 sec.)

Multi Inverter Assembly Components and Components Location

Component

1. High Voltage Junction Box Service Cover
1-a. 3.9 - 5,9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in)
2. Rear High Voltage Junction Box
2-a. 6.9 - 9,8 N·m
2-b. 15.7 - 24 N·m
2-c. 19.6 - 24 N·m
3. Multi Inverter Assembly
3-a. 3.9 - 5,9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in)

Multi Inverter Assembly Description and Operation

Description

  • The PE (Power Electric System) based on the E-GMP is composed of a motor, gearbox, inverter, and battery.
  • Unlike conventional electric vehicles, electric cars based on the E-GMP platform connect the motor and inverter internally, reducing weight caused by cables and decrease volume through integration.
  • It improves the driving distance of electric vehicles and maximizes driving efficiency.
  • The multi inverter assembly is installed on the rear-wheel drive motor and converts DC power to AC power (variable frequency, variable voltage).
  • In the case of driving and boost control for charging, it increases the voltage applied to the drive motor to obtain the appropriate driving force for the driving situation.
  • Inside the multi inverter assembly, it is divided into Inverter 1 and 2. During driving and charging, it maintains optimal conditions for both states through different controls (high-efficiency mode and high-power mode) suitable for each situation.
    The driving mode is determined by the motor system's torque or speed and the battery's available charge, but it can be changed based on the driver's acceleration intent.
    • High-Efficiency Mode: In typical driving situations, Inverter 1 operates to drive the vehicle at low or moderate speeds.
    • High-Power Mode: Both Inverter 1 and 2 operate simultaneously to drive the vehicle in situations requiring high speed or high torque.
  • By appropriately controlling inverters 1 and 2 during charging, the 800v high-voltage battery can be charged with the existing 400 V quick charger, improving efficiency in this case.
  • The 400 V boosts to 800 V when quick charge.
  • It is a next generation charging system for 400 V and 800 V multi-charging. In 400 V charging infrastructure, a motor and inverter are used to charge the 800 V battery and in the 800 V charging infrastructure, the battery is charged by the high voltage input from the charger.

Multi Inverter Assembly Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Remove the rear high voltage junction box. (Refer to High Voltage Distributing System - "Rear High Voltage Junction Box")
  2. Separate the multi inverter cooling quick connector hoses (A).
  3. Disconnect the multi inverter assembly connector (A).
  4. Separate the wiring protector (A) from multi inverter assembly.

    Tightening torque : 6.9 - 9,8 N·m

  5. Remove the ground cable (A) after removing the bolt from the motor.

    Tightening torque : 7.8 - 9,8 N·m

  6. Remove the multi inverter assembly cover (A) after removing the fasteners.
  7. Remove the multi inverter assembly (A) after removing the bolts.
    Tightening torque : 3.9 - 5,9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in)

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.
    • Install the multi inverter assembly to the specified torque.
    • If multi inverter assembly is dropped, it may cause internal damage. (Do not reuse)
    • Replace the gasket (A) and check the installation before installing the multi inverter assembly.
    • Perform the PE system leak test procedure before installing the multi-inverter assembly in the vehicle.
  2. Perform the Initialization of Automatic Resolver Offset Calibration procedures with the KDS. (S/W Management → Rear Motor Control Unit (MCU) → Initialization of Automatic Resolver Offset Calibration)
    Refer to the KDS screen for operating conditions and details.