Suspension System
Tire Pressure Monitoring System (TPMS)
In this manual: Suspension System
35steps
~210min
4/5difficulty
Done 0 of 35
Contents:
Components and Components Location
Component Location
| 1. Body Domain Control Unit | 2. TPMS Sensor |
Description and Operation
Description
The tire pressure monitoring system continuously monitors the pressure and temperature inside the tire to warn of changes in the pressure inside the tire that may affect the driving conditions of the vehicle. The TPMS control module analyzes information from the Wheel Electronic (WE) sensor mounted inside the wheel, determines the tire condition, and outputs a signal necessary for controlling the warning lamp. Tire Low Pressure Light TPMS light ON/OFF conditions- Lamp ON Conditions
- The lamp turns ON when the tire pressure decreases below the standard level.
- Lamp OFF
- Low pneumatic pressure: The warning lamp turns OFF when the tire pressure exceeds the pressure required to turn off the lamp.
- Lamp ON Conditions
- It on simultaneously with the tread lamp.
- It Indicates the position of tires with low pressure and air leaks.
- Lamp OFF
- OFF simultaneously with the tread lamp.
If the wheel position changes while driving, the system assumes the previous state, but the warning light illuminates correctly when the current driving position is determined. - Tread warning lights and wheel position warning lights may light up due to sudden changes in the outside temperature (especially in winter) and influences from driving.
- When the warning lamp turns on, check the inflation pressure and then inflate it to the specified tire pressure.
- Warning Conditions and Display
- When the system detects a fault outside the receiver or sensor, it blinks for about 1 minute and then turns on.
- When the system detects a receiver fault, it blinks for about 1 minute and then turns on.
- When the system detects a sensor fault, it blinks for about 1 minute and then turns on.
- Lamp OFF
- When the DTC is resolved, the warning light turns off, and the DTC is saved as a past fault.
- If this happens while driving, even if the DTC has been resolved, it should be checked again. (IG OFF and ON, then check the warning light again)
- The warning lamp turns off once the DTC is resolved. The warning lamp stays on until you complete the check necessary to resolve the DTC.
- If the DTC is resolved, the warning lamp turns OFF during the same ignition cycle.
If the vehicle starts within 19 minutes after the replacement of the wheel of the stopped vehicle, the TPMS Malfunction Indicator on the instrument cluster illuminates. - The above symptom is due to communication failure between the BCM and the replaced TPMS ID.
- This communication failure indicator turns off in 19 minutes after the vehicle stops through the BCM’s automatic learning process of TPMS ID. (When driving the vehicle after stopping for over 19 minutes, the indicator turns off automatically.)
- General Function
- The system detects many input elements to identify potential defects.
- The priority of a defect depends on its cause.
- Certain defects are not diagnosed as DTCs.
a. In order to diagnose more symptoms of the fault when the ignition line malfunctions, you must check the warning lamp when you turn the ignition on. b. Check whether the warning lamp turns on and then off.
TPMS Sensor Description and Operation
Description
- Function
- TPMS sensor (Transmitter) detects the motion and sends the pressure, temperature data via RF signal to ECU.
- By comparing ABS wheel pulses with sensor RF signal transmission locations, wheel automatic position learning is conducted to recognize the corresponding wheel position.
- Configurations and Features
- There are four (4) TPMS sensors mounted in each wheel of the vehicle.
- The frequency conversion type is FSK, and the carrier frequency is 433.92 MHz.
- Mode It consists of off mode, stop mode, rotation mode, and learning mode.
Illustration Function Valve type Snap-in type [rubber valve] Screw Screw T10 [Continental Certified Parts] ASIC Gen 6 Battery type CR2032 HR type
- Wheel angular velocity of wheels are different from each other in the following cases:
- Slip for each axis occurs differently.
- Rotation radius (the radius of curve) for each wheel is different.
- Tire wear, internal pressure, tire specifications, etc. for each tire are different.
- TPMS sensor is transmitted to RF signal at only specific phase (the angle of the tire) in the learning mode.
- TPMS receiver checks each tire phase (tire angle) information on receiving RF signals from the sensor.
- Every time RF signals from sensor IDs 1, 2, 3, and 4 are received, the ID with the highest correlation among the phase of each collected wheel is transmitted. (In other words, each time RF signal is received, the phase of the tire is transmitted to the most constant wheel.)
- TPMS sensor transmits the RF signal at intervals of 16 seconds in the learning mode.
- After stopping or parking for more than 19 minutes, automatic learning function in every driving position is performed.
- The sensor is converted to Parking Mode when stopped or parked for more than 15 minutes. When acceleration of over 4g (15-20 ㎞/h) is detected in Parking Mode, it is converted to First Block Mode.
TPMS Sensor Inspection
Inspection
How to inspect the tire pressure sensor after installation After installation, the TPMS sensor installation normal and fault conditions are determined by the following conditions: [Normal]- The valve stem is securely installed on the wheel.
- The transmitter evenly spaced without touching the wheel.
- The entire valve stem is pulled into the wheel.
- The valve and rim holes forming the same axis.
- The entire valve stem not fully seated on wheel.
- The valve stem is not securely installed on the wheel.
- The valve and rim holes are not forming the same axis.
TPMS Sensor Replacement
Replacement
- Remove the tire. (Refer to Wheel and Tire - "Tire")
- Remove the TPMS sensor mounting screw (A).
- When installing the tire bead, make sure that it does not come in contact with the TPMS sensor.
- Be careful not to damage the TPMS sensor when installing the tire bead near the TPMS sensor.
- Using a valve mounting tool, pull the sensor housing through the valve stem hole.
- Apply the surface of the new valve with lubricant and install it in the valve hole of the wheel.
Lubricant : Soapy water or YH 100 (Tire Lubricants)
- If the lower part of the TPMS sensor valve is not properly mounted on the wheel as shown below, sealing will not work properly.
- The groove of the valve stem body must be pulled through the hole.
- After applying lubricant, install the valve within 5 minutes. (After 5 minutes, relubricate)
- Install the wheel and tires. (Refer to Wheel and Tire - "Wheel")
- Drive the vehicle for automatic TPMS sensor learning.
- If automatic learning is not possible, perform the below procedure with KDS. (S/W management → BDC-TPMS → Wheel Sensor ID writing)
Refer to the KDS screen for operating conditions and details
TPMS Receiver Description and Operation
Description
TPMS monitors the pressure and temperature of tires to warn of pressure changes that may affect driving conditions. The messages calculated from the processed data are shown in the cluster through one warning lamp. Also, checking the ECU input and output signals by ERROR. And receive pressure data sensored while parking. The ECU processes the data received from the wheel sensors, determines the condition of the tires, and delivers the required warning messages to the driver via the CAN line or hardwire control line. TPMS Receiver : Integrated with BDC (Body Domain Control) Unit.- Initial state
- Platform information and sensor ID are not entered.
- Normal operation state
- In order to detect tire pressure and DTC, the receiver must be in normal operation.
- The receiver can check the sensor location and data.
Operation
- General Function
- Auto-learn takes place only once per ignition cycle.
- On successful completion, 4 road wheel sensor ID's are stored into memory for monitoring.
- Until auto-learn completes, previously learned sensors are monitored for under inflation / leak warnings.
- General Conditions to learn new sensors :
- Receiver must determine that it is confident that sensor is not temporary : a. Uses vehicle speed. b. Uses confidence reduction of previously learned sensors.
- Typical time for continuous driving over 15,5 mph to learn a new sensor is up to 10 minutes.
- General Conditions to un-learn a sensor that is removed :
- It takes less than 10 minutes at 12.4 - 18,6 mph.
- It depends on the vehicle's speed and the number of sensors input to the receiver.
TPMS Receiver On Vehicle Inspection. TPMS Receiver Removal and Installation
TPMS Receiver On Vehicle Inspection
Inspection
- Save the vehicle code, VIN, and sensor ID in the receiver and check whether it is properly stored.
- Check that the status of the TPMS receiver (BDC, Integrated Body Domain Control Unit) is in normal operation.
- Check whether the TPMS warning light is off and DTC code.
TPMS Receiver Removal and Installation
Removal and Installation
| The TPMS receiver is integrated with the Body Domain Control (BDC) unit, so replace the BDC unit. |
- Replace the Body Domain Control (BDC) unit. (Refer to Body - "Body Domain Control Unit")
Was this page helpful?