Transmission & Driveline

Precautions

11steps
~66min
5/5difficulty
Done 0 of 11

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER"

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision.

Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this Service Manual.

  • To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision that would result in air bag inflation, it is recommended that all maintenance and repair be performed by an authorized NISSAN/INFINITI dealer.

  • Improper repair, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag Module, see “SRS AIR BAG”.

  • Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors.

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

  • When using air or electric power tools or hammers, always switch the ignition/power switch OFF, disconnect the 12V battery or batteries, and wait at least 3 minutes before performing any service.

Precaution for Procedure without Cowl Top Cover

When performing the procedure after removing cowl top cover, cover the lower end of windshield with urethane, etc to prevent damage to windshield.

Precautions for Removing Battery Terminal

  • When disconnecting the 12V battery terminal, turn off the ACC power before disconnecting the 12V battery terminal, observing “How to disconnect 12V battery terminal” described below.

  • For Nissan Armada vehicles with the 2-batteries, be sure to connect the main battery and the sub battery before turning ON the ignition switch.

  • After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.

HOW TO DISCONNECT 12V BATTERY TERMINAL

Disconnect 12V battery terminal according to instruction described below.

  1. Open the hood.

  2. Turn ignition switch to the ON position.

  3. Turn ignition switch to the OFF position with the driver side door opened.

  4. Get out of the vehicle and close the driver side door.

  5. Wait at least 3 minutes. For vehicle with the engine listed below, remove the battery terminal after a lapse of the specified time.

    BR08DE : 4 minutes R9N engine : 12 minutes
    BR10DE : 12 minutes V9X engine : 4 minutes
    D4D engine : 20 minutes YD25DDTi : 2 minutes
    HR09DET : 12 minutes YS23DDT : 4 minutes
    HR10DDT : 12 minutes YS23DDTT : 4 minutes
    HR10DET : 12 minutes ZD30DDTi : 60 seconds
    HR13DDT : 12 minutes ZD30DDTT : 60 seconds
    HRA2DDT : 12 minutes K9K engine : 4 minutes
    M9R engine : 4 minutes R9M engine : 4 minutes
  6. Remove 12V battery terminal.

On Board Diagnostic (OBD) System of Engine and A/T

The ECM and TCM have an on board diagnostic system. It will illuminate the malfunction indicator lamp (MIL) to warn the driver of a malfunction causing emission deterioration.

General Precautions

  • Ignition switch OFF and disconnect the battery cable from the negative terminal before connecting or disconnecting the A/T assembly connector. Because battery voltage is applied to TCM even if ignition switch is switched OFF.

  • Perform “DTC (Diagnostic Trouble Code) CONFIRMATION PROCEDURE” after performing each TROUBLE DIAGNOSIS.

    If the repair is completed DTC should not be displayed in the “DTC CONFIRMATION PROCEDURE”.

  • Always use the specified brand of ATF.

  • Use lint-free paper not cloth rags during work.

  • Dispose of the waste oil using the methods prescribed by law, ordinance, etc. after replacing the ATF.

  • Before proceeding with disassembly, thoroughly clean the outside of the transmission. It is important to prevent the internal parts from becoming contaminated by dirt or other foreign matter.

  • Disassembly should be done in a clean work area.

  • Use lint-free paper or towels for wiping parts clean. Common shop rags can leave fibers that could interfere with the operation of the transmission.

  • Place disassembled parts in order for easier and proper assembly.

  • All parts should be carefully cleaned with a general purpose, non-flammable solvent before inspection or reassembly.

  • Gaskets, seals and O-rings should be replaced any time the A/T is disassembled.

  • It is very important to perform functional tests whenever they are indicated.

  • Properly installed valves, sleeves, plugs, etc. will slide along bores in valve body under their own weight.

  • Before assembly, apply a coat of recommended ATF to all parts. Apply petroleum jelly to protect O-rings and seals, or hold bearings and washers in place during assembly. Never use grease.

  • Extreme care should be taken to avoid damage to O-rings, seals and gaskets when assembling.

  • Occasionally, the parking gear may be locked with the torque insufficiently released, when stopping the vehicle by switching the shift position from “D” or “R” to “P” position with the brake pedal depressed.

    In this case, the shock with a thud caused by the abrupt release of torque may occur when switching the shift position “P” position to other positions.

    However, this symptom is not a malfunction which results in the damage of parts.

  • To avoid the risk of minor injury or property damage: If the 12-volt battery has low or no voltage, the transmission cannot be shifted. Replace the battery or repair the damaged power supply system. If towing the vehicle, follow the tow procedure, refer to Tow Truck Towing.

Service Notice or Precaution

ATF COOLER SERVICE

If ATF contains frictional material (clutches, bands, etc.), or if an A/T is repaired, overhauled, or replaced, inspect and clean the A/T fluid cooler mounted in the radiator or replace the radiator. Flush cooler lines using cleaning solvent and compressed air after repair. For A/T fluid cooler cleaning procedure, refer to Cleaning. For radiator replacement, refer to RADIATOR : Exploded View.

Precaution for when Jacking and Lifting Up the Vehicle with Electronic Air Suspension System

OPERATION PROCEDURE

Jacking up or lift up using the following steps.

  1. Start engine.

  2. Turn auto height mode control switch to ON, shift the shift position to N and set to normal height.

  3. Turn OFF the electronic air suspension function. Refer to Operation.

  4. Stop engine.

  5. Jacking up or lift up.

Precaution for Electronic Air Suspension System