Cruise Control & Driver Assistance

C1a42-23 Operation Sw Circ

16steps
~96min
4/5difficulty
Done 0 of 16
DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content)
DTC detection condition
C1A42-23

SYSTEM SW CIRC

(ICC switch circuit)
Diagnosis condition When engine is running
Signal (terminal) —
Threshold ICC steering switch ON status is detected continuously.
Diagnosis delay time 10 minutes or more

POSSIBLE CAUSE

  • ICC steering switch circuit

  • ICC steering switch

  • ECM

  • ADAS control unit

FAIL-SAFE

The following systems are canceled:

  • Vehicle-to-vehicle distance control mode

  • Conventional (fixed speed) cruise control mode

  • Automatic Emergency Braking (AEB) with pedestrian detection

  • Automatic Emergency Braking (AEB)

  • Intelligent Forward Collision Warning (I-FCW)

  • Intelligent Lane Intervention (I-LI)

Confirmation Procedure

CHECK DTC PRIORITY

CONSULT

If DTC “C1A42-23” is displayed with DTC “U1000-01”, first diagnose the DTC “U1000-01”.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Description.

NO>>

GO TO 2 .

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Turn the MAIN switch of ICC system ON.

  3. Perform “All DTC Reading”.

  4. Check if “C1A42-23” is detected as the current malfunction in the “Self Diagnostic Result” of “ICC/ADAS”.

Is “C1A42-23” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC “C1A42–23” is displayed with DTC “U1000–01”, first diagnose the DTC “U1000–01”.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Description.

NO>>

GO TO 2.

CHECK ICC STEERING SWITCH

  1. Turn the ignition switch OFF.

  2. Check the ICC steering switch. Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Replace the ICC steering switch. Refer to Removal and Installation.

CHECK HARNESS BETWEEN COMBINATION SWITCH (SPIRAL CABLE) AND ECM

  1. Disconnect the combination switch (spiral cable) connector M41 (with I-LI) or M30 (without I-LI)

  2. Disconnect the ECM connector E32.

  3. Check for continuity between the combination switch (spiral cable) harness connector and ECM harness connector.

    With I-LI
    Combination switch (spiral cable) ECM Continuity
    Connector Terminal Connector Terminal
    M41 14 E32 134 Yes
    15 135
    Without I-LI
    Combination switch (spiral cable) ECM Continuity
    Connector Terminal Connector Terminal
    M30 10 E32 134 Yes
    7 135
  4. Check for continuity between combination switch (spiral cable) harness connector and ground.

    With I-LI
    Combination switch (spiral cable) Ground Continuity
    Connector Terminal
    M41 14 No
    15
    Without I-LI
    Combination switch (spiral cable) Ground Continuity
    Connector Terminal
    M30 10 No
    7

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair the harnesses or connectors.

CHECK COMBINATION SWITCH (SPIRAL CABLE)

  1. Disconnect combination switch (spiral cable) connector M143 (with I-LI) or M149 (without I-LI).

  2. Check for continuity between combination switch (spiral cable) connector terminals.

With I-LI
Combination switch (spiral cable) Continuity
Connector Terminal Connector Terminal
M41 14 M143 34 Yes
15 35
Without I-LI
Combination switch (spiral cable) Continuity
Connector Terminal Connector Terminal
M30 10 M149 15 Yes
7 18

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Replace the combination switch (spiral cable). Refer to Removal and Installation.

PERFORM SELF-DIAGNOSIS OF ECM

  1. Connect the connectors of Combination switch (spiral cable) and ECM.

  2. Turn the ignition switch ON.

  3. Perform “All DTC Reading”.

  4. Check if any DTC is detected in “Self Diagnostic Result” of “ENGINE”.

Is any DTC detected?

YES>>

Perform self-diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to DTC Index.

NO>>

Replace the ADAS control unit. Refer to Removal and Installation.

Component Inspection

CHECK ICC STEERING SWITCH

Check resistance between combination switch (spiral cable) terminals.

With Intelligent Lane Intervention
TerminalSwitch operationResistance [Ω]
34 35 When pressing MAIN switch Approx. 1
When pressing CANCEL switch Approx. 309
When pressing DISTANCE switch Approx. 741
When pressing SET/COAST switch Approx. 1406
When pressing RESUME/ACCELERATE switch Approx. 2586
When all switches are not pressed Approx. 5456
Without Intelligent Lane Intervention
TerminalSwitch operationResistance [Ω]
15 18 When pressing MAIN switch Approx. 1
When pressing CANCEL switch Approx. 309
When pressing DISTANCE switch Approx. 741
When pressing SET/COAST switch Approx. 1406
When pressing RESUME/ACCELERATE switch Approx. 2586
When all switches are not pressed Approx. 5456

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace the ICC steering switch. Refer to Removal and Installation.