Parking Brake

Electric Parking Brake AUTO Indicator Circuit

~6min read

DESCRIPTION

Pulling the electric parking brake switch toward the lock side for at least 5 seconds turns the AUTO function (function linked to gear shifting) ON, and an AUTO ON mode message is displayed on the multi-information display of the combination meter.

Pushing the electric parking brake switch toward the unlock side for at least 5 seconds turns the AUTO function (function linked to gear shifting) OFF, and an AUTO OFF mode message is displayed on the multi-information display of the combination meter.

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

  • Check the fuses for the circuits related to this system before performing the following inspection procedure.
  • The electric parking brake may still operate for 20 seconds after the ignition switch is turned OFF. Before disconnecting connectors or fuses, turn the ignition switch OFF and wait at least 20 seconds.
  • When replacing the skid control ECU (brake actuator assembly), operate the electric parking brake switch (electric parking brake switch assembly) when the parking brake indicator (red) flashes after the ignition switch is turned ON for the first time.

PROCEDURE

  1. INSPECT CAN COMMUNICATION SYSTEM

(a) Check whether CAN communication system DTCs are output.

Click here

Result:

Result

Proceed to

No DTCs are output

A

DTCs are output

B

B

GO TO CAN COMMUNICATION SYSTEM

A
  1. READ VALUE USING TECHSTREAM (AUTO MODE)

(a) Turn the ignition switch OFF.

(b) Connect the Techstream to the DLC3.

(c) Turn the ignition switch to ON and turn on Techstream.

(d) Select the following menus: Chassis / Electric Parking Brake / Data List.

(e) Check the values by referring to the table below.

Chassis > ABS/VSC/TRAC/EPB > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

Auto Mode

AUTO mode permission display (linked to gear shifting)

OFF or ON

OFF: Manual mode

ON: AUTO mode (linked to shift operation)

-

Chassis > ABS/VSC/TRAC/EPB > Data List

Auto Mode

(f) When switching the mode, check that the Data List screen turns on and off.

Result:

Result

Proceed to

The AUTO indicator does not turn on and off when the Active Test is set to ON and OFF.

A

The AUTO indicator turns on and off when the Active Test is set to ON and OFF.

B

B

GO TO STEP 6

A
  1. CHECK DTCs

(a) Check the DTCs.

Click here

Chassis > ABS/VSC/TRAC/EPB > Trouble Codes

Result:

Result

Proceed to

DTC is not output

A

DTC DTC is output

B

B

GO TO DIAGNOSTIC TROUBLE CODE CHART

A
  1. INSPECT ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)

(a) Inspect the electric parking brake switch (electric parking brake switch assembly).

Click here

NG

REPLACE ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)

OK
  1. INSPECT WIRE HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY))

(a) Disconnect connector F67 from the electric parking brake switch (electric parking brake switch assembly).

(b) Disconnect the A42 connector from the Skid Control ECU (Brake Actuator Assembly).

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

A42-31 (SWI1) - F67-6 (SWI1)

Always

Below 5 Ω

A42-32 (SWO1) - F67-5 (SWO1)

Always

Below 5 Ω

A42-15 (SWI2) - F67-4 (SWI2)

Always

Below 5 Ω

A42-16 (SWO2) - F67-3 (SWO2)

Always

Below 5 Ω

A42-31 (SWI1) or F67-6 (SWI1) - Body ground

Always

10 kΩ minimum

A42-32 (SWO1) or F67-5 (SWO1) - Body ground

Always

10 kΩ minimum

A42-15 (SWI2) or F67-4 (SWI2) - Body ground

Always

10 kΩ minimum

A42-16 (SWO2) or F67-3 (SWO2) - Body ground

Always

10 kΩ minimum

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. PERFORM ACTIVE TEST USING TECHSTREAM (AUTO MODE)

(a) Turn the ignition switch OFF.

(b) Connect the Techstream to the DLC3.

(c) Turn the ignition switch to ON.

(d) Turn on the Techstream.

(e) Select the following menu items: Chassis / Electric Parking Brake / Data List.

(f) Read the Data List by following the Techstream instructions.

Click here

Chassis > ABS/VSC/TRAC/EPB > Active Test

Tester display

Item

Control Range

Diagnostic Note

Auto Mode

AUTO mode (linked to gear change)

ON or OFF

  • Vehicle stopped
  • Ignition Switch in ON position
Chassis > ABS/VSC/TRAC/EPB > Active Test

Auto Mode

(g) Select the Data List on Techstream.

Chassis > ABS/VSC/TRAC/EPB > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

Auto Mode

AUTO mode permission display (linked to gear shifting)

ON or OFF

ON: AUTO mode (linked to shift operation)

OFF: Manual mode

-

Chassis > ABS/VSC/TRAC/EPB > Data List

Auto Mode

(h) Perform the Active Test Auto Mode, then check whether the Data List screen changes.

Result:

Result

Proceed to

Check the operating condition of the "Auto Mode" when it is activated using the Techstream.

A

"Auto Mode" in the Data List is enabled/disabled using the Active Test.

B

A

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

B
  1. CHECK COMBINATION METER ASSEMBLY

(a) Perform the Active Test of the combination meter assembly using the Techstream. (for CVT)

Click here

Body Electrical > Combination Meter > Active Test

Meter Display 1

(b) Check whether the multi-information display of the combination meter assembly turns on or off according to the Techstream operation.

OK:

The message on the multi-information display appears and disappears according to the Active Test operation.

OK

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

NG

GO TO METER/GAUGE SYSTEM