Parking Brake

Electric parking brake does not operate

~4min read

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

  • Check the fuses for the circuits related to this system before performing the following inspection procedure.
  • The electric parking brake may still operate for 20 seconds after the ignition switch is turned OFF. Before disconnecting connectors or fuses, turn the ignition switch OFF and wait at least 20 seconds.
  • When replacing the skid control ECU (brake actuator assembly), operate the electric parking brake switch assembly while the parking brake indicator flashes (red) when the ignition switch is first turned to ON.

HINT:

Even if the electric parking brake operates normally, the parking brake indicator (red) on the combination meter may malfunction.

PROCEDURE

  1. INSPECT CAN COMMUNICATION SYSTEM

(a) Check whether CAN communication system DTCs are output.

Click here

Chassis > Electric Parking Brake > Trouble Codes

Result:

Result

Proceed to

No DTCs are output

A

DTCs are output

B

B

GO TO CAN COMMUNICATION SYSTEM

A
  1. VEHICLE OPERATION CHECK

(a) When the vehicle tires are lifted off the ground and Techstream is used to operate the electric parking brake, check the rear tires.

Click here

Result:

Result

Proceed to

Lock and unlock operation is normal and the parking brake indicator turns off or flashes (red)

A

Lock and unlock operation is malfunctioning and the parking brake indicator turns on (red) or turns on and off depending on switch operation

B

Lock and unlock operation is malfunctioning and the parking brake indicator turns off or flashes (red)

C

B

CHECK REAR BRAKE

C

GO TO STEP 5

A
  1. PERFORM ACTIVE TEST USING TECHSTREAM (PARKING BRAKE LIGHT)

(a) Turn the ignition switch OFF.

(b) Connect the Techstream to the DLC3.

(c) Turn the ignition switch to ON.

(d) Turn on the Techstream.

(e) Select the following menu items: Chassis / Electric Parking Brake / Data List.

(f) Read the Data List by following the Techstream instructions.

Click here

Chassis > ABS/VSC/TRAC/EPB > Active Test

Tester display

Item

Control Range

Diagnostic Note

PKB Light

Parking brake warning light (red)

ON or OFF

  • Vehicle stopped
  • Ignition Switch in ON position
  • Parking brake released
Chassis > ABS/VSC/TRAC/EPB > Active Test

PKB Light

(g) Select the Data List on Techstream.

Click here

Chassis > ABS/VSC/TRAC/EPB > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

Parking Brake Light

Parking Brake Warning Light Output Signal (red)

OFF, Light or Blink

OFF: Parking brake (red) warning light turns off

Light: Parking brake (red) warning light turns on

Blink: Parking brake (red) warning light flashes

-

Chassis > ABS/VSC/TRAC/EPB > Data List

Parking Brake Light

(h) Check the parking brake indicator (red) operation when activated using Techstream.

Result:

Result

Proceed to

The parking brake indicator (red) in the data list does not change with the Active Test.

A

The parking brake indicator (red) in the data list is turned on/off with the Active Test.

B

A

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

B
  1. CHECK COMBINATION METER ASSEMBLY

(a) Perform the Active Test of the combination meter assembly using the Techstream.

Click here

Body Electrical > Combination Meter > Active Test

Park Indicator

(b) Check the combination meter assembly.

OK:

The parking brake indicator (red) turns on or off depending on Techstream operation.

OK

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

NG

GO TO METER/GAUGE SYSTEM

  1. CHECK HARNESS AND CONNECTOR (BATTERY - SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY))

(a) Turn the ignition switch OFF.

(b) Disconnect the A42 connector from the Skid Control ECU (Brake Actuator Assembly).

*a

Front view of wire harness side connector

(to Skid Control ECU (Brake Actuator Assembly))

(c) Measure the voltage according to the value(s) shown in the table below.

Standard voltage:

Tester Connection

Ignition switch position

Specified Condition

A42-36 (IG1) - Body ground

Ignition Switch in ON position

11 à 14 V

OK

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR