Parking Brake

Test Mode Procedure

11steps
~66min
3/5difficulty
Done 0 of 11

TEST MODE PROCEDURE

REAR BRAKE PAD REPLACEMENT MODE

*1

Rear Disc Brake Piston

*2

Nut

*a

Nut Moves Inward in Pad Replacement Mode

HINT:

When replacing the rear disc brake pads and rear disc, the nut inside the rear disc brake cylinder assembly is in an advanced position, so it is necessary to move the nut back inside the cylinder. The nut can be moved back using the pad replacement mode.

(a) Pad Replacement Mode

When using the Techstream:
  1. Turn the ignition switch OFF.
  2. Connect the Techstream to the DLC3.
  3. Turn the ignition switch ON.
  4. Turn on the Techstream.
  5. Select the following menus: Chassis / ABS/VSC/TRAC/EPB / Utility / Check Mode
  6. Follow the Techstream display and select "Next".
  7. Hold the Electric Parking Brake Switch (Electric Parking Brake Switch Assembly) in the released position for at least 5 seconds.

    NOTICE:

    • Be sure to perform this procedure with the ignition switch in the ON position.
    • Make sure the brake pedal is not depressed when performing this procedure.
    • When the system enters brake pad replacement mode, DTC C13A7/43 may be stored. If the DTC is stored, clear the DTCs after the procedure (rear disc brake pad replacement, etc.) is completed.

    HINT:

    The parking brake indicator light flashes (red) at 0.25-second intervals. After a short time, the parking brake actuator assembly operates (when the parking brake is applied, the electric motor operates to release the parking brake, and then it may operate again). Once the parking brake actuator assembly is in the pad replacement position, the parking brake indicator light flashes (red) at 1-second intervals.

Chassis > ABS/VSC/TRAC/EPB > Utility

Check Mode

When not using the Techstream:
  1. Turn the ignition switch OFF.
  2. Turn the ignition switch ON.
  3. Within 8 seconds, operate the electric parking brake switch (electric parking brake switch assembly) 3 times in the ON position on the lock side (from OFF (released) to ON (pulled)), then 3 times in the ON position on the release side (from OFF (released) to ON (pressed)).

    NOTICE:

    • If the operation is performed too quickly, the system may not respond. If the system does not respond, perform the operation again more slowly.
    • The parking brake must be released.

    HINT:

    The parking brake indicator light (red) flashes at 0.25-second intervals.

  4. Hold the Electric Parking Brake Switch (Electric Parking Brake Switch Assembly) in the released position for at least 5 seconds.

    NOTICE:

    • Be sure to perform this procedure with the ignition switch in the ON position.
    • Make sure the brake pedal is not depressed when performing this procedure.
    • When the system enters brake pad replacement mode, DTC C13A7 may be stored. If the DTC is stored, clear the DTCs after the procedure (rear disc brake pad replacement, etc.) is completed.

    HINT:

    After a short delay, the parking brake actuator assembly operates (if it is operated by the parking brake in the locked position, the parking brake actuator assembly motor temporarily stops after being activated, then operation resumes). Once the assembly has finished operating, the parking brake indicator light (red) flashes slowly at 1-second intervals. (The nut returns inside the cylinder and the system enters brake pad replacement mode.)

(b) Turn the ignition switch OFF.

NOTICE:

Do not operate the electric parking brake switch (electric parking brake switch assembly) before the procedure is completed. If it is operated, the system returns to normal condition.

When using the Techstream:
  1. Disconnect the Techstream from the DLC3.

(c) Return to Normal Conditions

(1) After the procedure (rear disc brake pad replacement, etc.) is completed, turn the ignition switch to ON and pull the electric parking brake switch (electric parking brake switch assembly) toward the lock side for at least 5 seconds.

NOTICE:

  • When performing this task (rear disc brake pad replacement, etc.), do not operate the electric parking brake switch (electric parking brake switch assembly), or turn the ignition switch to ON and operate the shift lever. If the electric parking brake switch (electric parking brake switch assembly) or the shift lever is operated, the parking brake may operate and the rear disc brake piston may fall out. Also be sure to disconnect the connector of the parking brake actuator assembly or disconnect the cable from the negative (-) battery terminal.
  • If DTC C13A7 is stored, clear the DTCs.