Parking Brake

Open or short in electric motor circuit (C13A6)

~5min read

DESCRIPTION

DTC No.

Detection Item

DTC Detection Condition

Suspected Area

Memory

Note

C13A6

Open or short in electric motor circuit

An open or short circuit in the parking brake actuator assembly is detected for at least 0.015 seconds.

  • Parking brake actuator assembly
  • Wire harness or connector
  • Skid control ECU (brake actuator assembly)

DTC recorded

A malfunction in the electric parking brake system is displayed on the multi-information display.

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

  • The electric parking brake may still operate for 20 seconds after the ignition switch is turned OFF. Before disconnecting connectors or fuses, turn the ignition switch OFF and wait at least 20 seconds.
  • When replacing the skid control ECU (brake actuator assembly), operate the electric parking brake switch assembly while the parking brake indicator flashes (red) if the ignition switch is turned to ON for the first time.

PROCEDURE

  1. READ VALUE USING TECHSTREAM (PERMISSION OF RH INTERLOCKING PKB LOCK / PERMISSION OF LH INTERLOCKING PKB LOCK)

(a) Turn the ignition switch OFF.

(b) Connect the Techstream to the DLC3.

(c) Turn the ignition switch to ON.

(d) Turn on the Techstream.

(e) Select the following menu items: Chassis / Electric Parking Brake / Data List.

(f) Read the Data List by following the Techstream instructions.

Chassis > ABS/VSC/TRAC/EPB > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

RH Interlocking PKB Lock Permission

RH Parking Brake Actuator Assembly PKB Lock Control Permission Status

OK or NG

-

-

LH Interlocking PKB Lock Permission

Left Parking Brake Actuator Assembly Parking Brake Lock Control Permission Status

OK or NG

-

-

Chassis > ABS/VSC/TRAC/EPB > Data List

Tester display

RH Interlocking PKB Lock Permission

LH Interlocking PKB Lock Permission

NEXT
  1. INSPECT PARKING BRAKE CABLE ASSEMBLY

*a

Front view of parking brake cable assembly

*b

(to wire harness connector)

*c

(to parking brake actuator assembly)

*d

for right side

*e

for left side

-

-

(a) Remove the parking brake cable assembly.

Click here

(b) Check that the parking brake cable assembly is not damaged.

OK:

No damage.

HINT:

If damaged, a short in the wire harness or a short to ground may be present.

(c) Inspect the parking brake cable assembly.

Standard resistance:

for right side

Tester Connection

Condition

Specified Condition

dM3-2 (MRR-) - d2-1 (MRR-)

Always

Below 1 Ω

dM3-2 (MRR-) - d2-2 (MRR+)

Always

10 kΩ minimum

dM3-2 (MRR-) or d2-1 (MRR-) - Body ground

Always

10 kΩ minimum

dM3-1 (MRR+) - d2-2 (MRR+)

Always

Below 1 Ω

dM3-1 (MRR+) - d2-1 (MRR-)

Always

10 kΩ minimum

dM3-1 (MRR+) or d2-2 (MRR+) - Body ground

Always

10 kΩ minimum

for left side

Tester Connection

Condition

Specified Condition

eM3-2 (MRL-) - e2-1 (MRL-)

Always

Below 1 Ω

eM3-2 (MRL-) - e2-2 (MRL+)

Always

10 kΩ minimum

e2-1 (MRL-) or e3-2 (MRL-) - Body Ground

Always

10 kΩ minimum

e3-1 (MRL+) - e2-2 (MRL+)

Always

Below 1 Ω

e3-1 (MRL+) - e2-1 (MRL-)

Always

10 kΩ minimum

e3-1 (MRL+) or e2-2 (MRL+) - Body Ground

Always

10 kΩ minimum

NG

REPLACE PARKING BRAKE CABLE ASSEMBLY

OK
  1. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - PARKING BRAKE ACTUATOR ASSEMBLY)

(a) Turn the ignition switch OFF.

(b) Make sure the parking brake cable assembly is correctly seated.

(c) Disconnect connector A42 from the skid control ECU (brake actuator assembly).

(d) Disconnect parking brake actuator assembly connector d2*1 or e2*2.

  • *1: for RH side
  • *2: for LH side

(e) Measure the resistance according to the value(s) in the table below.

Standard resistance:

for right side

Tester Connection

Condition

Specified Condition

A42-2 (MRR+) - d2-2 (MRR+)

Always

Below 1 Ω

A42-3 (MRR-) - d2-1 (MRR-)

Always

Below 1 Ω

A42-2 (MRR+) or d2-2 (MRR+) - Body Ground

Always

10 kΩ minimum

A42-3 (MRR-) or d2-1 (MRR-) - Body Ground

Always

10 kΩ minimum

for left side

Tester Connection

Condition

Specified Condition

A42-13 (MRL+) - e2-2 (MRL+)

Always

Below 1 Ω

A42-12 (MRL-) - e2-1 (MRL-)

Always

Below 1 Ω

A42-13 (MRL+) or e2-2 (MRL+) - Body Ground

Always

10 kΩ minimum

A42-12 (MRL-) or e2-1 (MRL-) - Body Ground

Always

10 kΩ minimum

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK PARKING BRAKE ACTUATOR ASSEMBLY

(a) Check the parking brake actuator assembly.

Click here

OK

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

NG

REPLACE PARKING BRAKE ACTUATOR ASSEMBLY