Parking Brake

EPB switch malfunction (C13B4)

~4min read

DESCRIPTION

When the electric parking brake switch is pulled, the skid control ECU (brake actuator assembly) sends a lock request signal to the parking brake actuator assembly. When the electric parking brake switch is pushed, the skid control ECU (brake actuator assembly) sends an unlock request signal to the parking brake actuator assembly.

DTC No.

Detection Item

DTC Detection Condition

Suspected Area

Memory

Note

C13B4

EPB switch malfunction

  • Parking brake switch power supply voltage at +BS terminal below 7 V for 1 second or more
  • Open or short in parking brake switch detected for 0.3 second or more
  • Parking brake switch lock malfunction
  • Electric parking brake switch (electric parking brake switch assembly)
  • Wire harness or connector
  • Skid control ECU (brake actuator assembly)

DTC recorded

A malfunction in the electric parking brake system is displayed on the multi-information display.

DTC Detection Conditions

Vehicle Operating Conditions

Sequence 1

Sequence 2

Sequence 3

Sequence 4

Diagnostic Condition

-

-

-

-

-

Malfunction Status

Parking brake switch power supply voltage at +BS terminal below 7 V

○

-

-

-

Open in parking brake switch circuit detected

-

○

-

-

Short in parking brake switch detected

-

-

○

-

Parking brake switch lock malfunction

-

-

-

○

Detection Duration

at least 1 second

0.3 seconds minimum

0.3 seconds minimum

-

Number of Trips

1 trip(s)

1 trip(s)

1 trip(s)

1 trip(s)

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

  • The electric parking brake may still operate for 20 seconds after the ignition switch is turned OFF. Before disconnecting connectors or fuses, turn the ignition switch OFF and wait at least 20 seconds.
  • When replacing the skid control ECU (brake actuator assembly), operate the electric parking brake switch (electric parking brake switch assembly) when the parking brake indicator (red) flashes after the ignition switch is turned ON for the first time.

PROCEDURE

  1. INSPECT ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)

(a) Inspect the electric parking brake switch (electric parking brake switch assembly).

Click here

NG

REPLACE ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)

OK
  1. INSPECT WIRE HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY))

(a) Disconnect connector F67 from the electric parking brake switch (electric parking brake switch assembly).

(b) Disconnect the A42 connector from the Skid Control ECU (Brake Actuator Assembly).

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

A42-31 (SWI1) - F67-6 (SWI1)

Always

Below 5 Ω

A42-32 (SWO1) - F67-5 (SWO1)

Always

Below 5 Ω

A42-15 (SWI2) - F67-4 (SWI2)

Always

Below 5 Ω

A42-16 (SWO2) - F67-3 (SWO2)

Always

Below 5 Ω

A42-31 (SWI1) or F67-6 (SWI1) - Body ground

Always

10 kΩ minimum

A42-32 (SWO1) or F67-5 (SWO1) - Body ground

Always

10 kΩ minimum

A42-15 (SWI2) or F67-4 (SWI2) - Body ground

Always

10 kΩ minimum

A42-16 (SWO2) or F67-3 (SWO2) - Body ground

Always

10 kΩ minimum

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK DTCs

(a) Clear the DTCs.

Click here

Chassis > ABS/VSC/TRAC/EPB > Clear DTCs

(b) Turn the ignition switch OFF.

(c) Turn the ignition switch to ON.

(d) Check the DTCs.

Click here

Chassis > ABS/VSC/TRAC/EPB > Trouble Codes

Result:

Result

Proceed to

DTCs are output

A

No DTCs are output

B

A

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

B

USE SIMULATION METHOD TO CHECK