Parking Brake

Actuator malfunction (C13A7)

~6min read

DESCRIPTION

DTC No.

Detection Item

DTC Detection Condition

Suspected Area

Memory

Note

C13A7

Actuator malfunction

When the electric parking brake is operating, motor lock, pinion lock, motor slip or repeated slipping occurs.

  • Parking brake actuator assembly
  • Rear brake
  • Wire harness or connector

DTC recorded

A malfunction in the electric parking brake system is displayed on the multi-information display.

WIRING DIAGRAM

Click here

PRECAUTION / NOTICE / HINT

NOTICE:

  • This DTC may be stored when the system enters pad replacement mode, but it is not a malfunction.
  • This DTC may be stored when the parking brake is forcibly released, but it is not a malfunction.
  • The electric parking brake may still operate for 20 seconds after the ignition switch is turned OFF. Before disconnecting connectors or fuses, turn the ignition switch OFF and wait at least 20 seconds.
  • When replacing the skid control ECU (brake actuator assembly), operate the electric parking brake switch (electric parking brake switch assembly) when the parking brake indicator (red) flashes after the ignition switch is turned ON for the first time.

PROCEDURE

  1. CHECK DTCs

(a) Check the DTCs.

Click here

Chassis > ABS/VSC/TRAC/EPB > Trouble Codes

Result:

Result

Proceed to

Only DTC C13A7 is output

A

DTCs other than C13A7 are output

B

B

GO TO DIAGNOSTIC TROUBLE CODE CHART

A
  1. READ VALUE USING TECHSTREAM (PERMISSION OF RH INTERLOCKING PKB LOCK / PERMISSION OF LH INTERLOCKING PKB LOCK)

(a) Turn the ignition switch OFF.

(b) Connect the Techstream to the DLC3.

(c) Turn the ignition switch to ON.

(d) Turn on the Techstream.

(e) Select the following menu items: Chassis / Electric Parking Brake / Data List.

(f) Read the Data List by following the Techstream instructions.

Chassis > ABS/VSC/TRAC/EPB > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

RH Interlocking PKB Lock Permission

RH Parking Brake Actuator Assembly PKB Lock Control Permission Status

OK or NG

-

-

LH Interlocking PKB Lock Permission

Left Parking Brake Actuator Assembly Parking Brake Lock Control Permission Status

OK or NG

-

-

Chassis > ABS/VSC/TRAC/EPB > Data List

Tester display

RH Interlocking PKB Lock Permission

LH Interlocking PKB Lock Permission

NEXT
  1. INSPECT PARKING BRAKE CABLE ASSEMBLY

*a

Front view of parking brake cable assembly

*b

(to wire harness connector)

*c

(to parking brake actuator assembly)

*d

for right side

*e

for left side

-

-

(a) Remove the parking brake cable assembly.

Click here

(b) Check that the parking brake cable assembly is not damaged.

OK:

No damage.

HINT:

If damaged, a short in the wire harness or a short to ground may be present.

(c) Inspect the parking brake cable assembly.

Standard resistance:

for right side

Tester Connection

Condition

Specified Condition

dM3-2 (MRR-) - d2-1 (MRR-)

Always

Below 1 Ω

dM3-2 (MRR-) - d2-2 (MRR+)

Always

10 kΩ minimum

dM3-2 (MRR-) or d2-1 (MRR-) - Body ground

Always

10 kΩ minimum

dM3-1 (MRR+) - d2-2 (MRR+)

Always

Below 1 Ω

dM3-1 (MRR+) - d2-1 (MRR-)

Always

10 kΩ minimum

dM3-1 (MRR+) or d2-2 (MRR+) - Body ground

Always

10 kΩ minimum

for left side

Tester Connection

Condition

Specified Condition

eM3-2 (MRL-) - e2-1 (MRL-)

Always

Below 1 Ω

eM3-2 (MRL-) - e2-2 (MRL+)

Always

10 kΩ minimum

e2-1 (MRL-) or e3-2 (MRL-) - Body Ground

Always

10 kΩ minimum

e3-1 (MRL+) - e2-2 (MRL+)

Always

Below 1 Ω

e3-1 (MRL+) - e2-1 (MRL-)

Always

10 kΩ minimum

e3-1 (MRL+) or e2-2 (MRL+) - Body Ground

Always

10 kΩ minimum

NG

REPLACE PARKING BRAKE CABLE ASSEMBLY

OK
  1. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - PARKING BRAKE ACTUATOR ASSEMBLY)

(a) Turn the ignition switch OFF.

(b) Make sure the parking brake cable assembly is correctly seated.

(c) Disconnect connector A42 from the skid control ECU (brake actuator assembly).

(d) Disconnect parking brake actuator assembly connector d2*1 or e2*2.

  • *1: for RH side
  • *2: for LH side

(e) Measure the resistance according to the value(s) in the table below.

Standard resistance:

for right side

Tester Connection

Condition

Specified Condition

A42-2 (MRR+) - d2-2 (MRR+)

Always

Below 1 Ω

A42-3 (MRR-) - d2-1 (MRR-)

Always

Below 1 Ω

A42-2 (MRR+) or d2-2 (MRR+) - Body Ground

Always

10 kΩ minimum

A42-3 (MRR-) or d2-1 (MRR-) - Body Ground

Always

10 kΩ minimum

for left side

Tester Connection

Condition

Specified Condition

A42-13 (MRL+) - e2-2 (MRL+)

Always

Below 1 Ω

A42-12 (MRL-) - e2-1 (MRL-)

Always

Below 1 Ω

A42-13 (MRL+) or e2-2 (MRL+) - Body Ground

Always

10 kΩ minimum

A42-12 (MRL-) or e2-1 (MRL-) - Body Ground

Always

10 kΩ minimum

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK REAR BRAKE AND PARKING BRAKE ACTUATOR ASSEMBLY

(a) Enter the rear brake pad replacement mode.

Click here

(b) Turn the ignition switch OFF.

(c) Make sure the rotating parts are not seized and the actuator turns freely.

(1) Check that the parking brake actuator assembly is correctly seated on the rear brake caliper and turns freely.

For the parking brake actuator assembly removal procedure: Click here

(2) Make sure there is no damage to the rotating parts from the parking brake actuator assembly to the rear brake caliper.

(3) Check the parking brake actuator assembly to make sure it operates correctly.

Click here

(4) Make sure the threaded part of the rear brake caliper turns and the rear disc brake piston moves outward.

HINT:

For check procedures, refer to the parking brake forced release method without using Techstream.

  • TMC manufactured

    Click here

  • TMMT manufactured

    Click here

HINT:

Return to normal mode after the work is completed.

Click here

OK

REPLACE PARKING BRAKE ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE NECESSARY PARTS