Exterior Lighting

Adjustment

~8min read

ADJUSTMENT

PROCEDURE

1. PREPARE VEHICLE FOR HEADLIGHT AIM ADJUSTMENT

(a) Prepare the vehicle:

  • Make sure the vehicle body is not damaged or deformed around the headlights.
  • Fill the fuel tank.
  • Make sure that the oil is at the specified level.
  • Make sure that the engine coolant is at the specified level.
  • Inflate the tires to the specified pressure.
  • Unload the luggage compartment and the vehicle, and check that the spare tire, tools and jack are in their original positions.
  • Bounce the vehicle at each corner to stabilize the suspension.
  • Have a person of average weight (75 kg, 165 lb.) sit in the driver's seat.

2. PREPARE VEHICLE FOR HEADLIGHT AIM ADJUSTMENT (using a screen)

(a) Prepare the vehicle:

*a

Center mark

  • Park the vehicle in a location dark enough to clearly see the cutoff line. The cutoff line is a distinct line below which the headlight light is perceived and above which it is not.
  • Position the vehicle at a 90° angle to the wall.
  • Keep a distance of 7.62 m (25 ft) between the vehicle (headlight center marks) and the wall.
  • Make sure that the vehicle is parked on a level surface.
  • Align the front wheels with the vehicle's centerline.
  • Shake the vehicle to stabilize the suspension.

NOTICE:

A distance of 7.62 m (25 ft) between the vehicle (headlight center marks) and the wall is required to correctly adjust the headlight aim. If this distance cannot be obtained, use a distance of exactly 3 m (9.84 ft) for checking and adjusting the headlight aim. (the target area size will change depending on the distance, so follow the illustration).

(b) Prepare a thick sheet of white paper (approximately 2 m (6.56 ft) (height) x 4 m (13.1 ft) (width)) to use as a screen.

(c) Draw a vertical line from top to bottom at the center of the screen (V line).

(d) Position the screen as shown in the illustration:

HINT:

  • Position the screen perpendicular to the floor.
  • Align the V line of the screen with the center of the vehicle.

(e) Draw the reference lines (H line, left V line and right V line) on the screen as shown in the illustration.

*a

Left V line

*b

V line

*c

Right V line

*d

H line

*e

Ground

HINT:

Mark the headlight bulb center points on the screen.

*a

Center mark

(1) H line (headlight height):

Draw a horizontal line across the screen passing through the center marks. The H line should be at the same height as the headlight center marks.

(2) Left V line, right V line (left and right headlight center mark positions):

Draw 2 vertical lines crossing the H line at each of the center marks (aligned with the headlight center marks).

3. INSPECT HEADLIGHT AIM

(a) Cover the headlight on the opposite side to prevent light from the headlight not being inspected from affecting the headlight aim check.

NOTICE:

Do not leave the headlight covered for more than 3 minutes. The headlight lens is made of synthetic resin and can easily melt or be damaged by heat.

(b) Start the engine.

(c) Turn on the headlights and check whether the cutoff line of each low beam matches the prescribed cutoff line, as shown in the illustration.

HINT:

  • Since the low beams and high beams form one unit, if the low beam aim is correct, the high beam aim is also correct. However, check both sides to be certain.
  • If the aiming distance is 25 m (82 ft):

    The low beam cutoff line must be between 48 mm (1.89 in) and 698 mm (2.29 ft) below the H line, and no more than 248 mm (9.79 in) to the left or right of the left or right V line.

  • If the aiming distance is 3 m (9.84 ft):

    The low beam cutoff line must be between 6 mm (0.227 in) and 83 mm (3.29 in) below the H line, and no more than 29 mm (1.17 in) to the left or right of the left or right V line.

  • If the aiming distance is 25 m (82 ft):

    The specified low beam target horizontal cutoff line must be 249 mm (9.79 in) below the H line, and point A of the specified low beam target cutoff line must be on the left or right V line.

  • If the aiming distance is 3 m (9.84 ft):

    The specified low beam target horizontal cutoff line must be 30 mm (1.18 in) below the H line, and point A of the specified low beam target cutoff line must be on the left or right V line.

(d) Turn on the high beams and check whether the center of intensity of each high beam matches the prescribed center of intensity shown in the illustration.

HINT:

  • Since the low beams and high beams form one unit, if the low beam aim is correct, the high beam aim is also correct. However, check both sides to be certain.
  • If the aiming distance is 25 m (82 ft):

    The high beam center of intensity must be no more than 174 mm (6.87 in) above and 248 mm (9.79 in) below the H line, and no more than 497 mm (1.63 ft) to the left or right of the left or right V line.

  • If the aiming distance is 3 m (9.84 ft):

    The high beam center of intensity must be no more than 20 mm (0.824 in) above and 29 mm (1.17 in) below the H line, and no more than 59 mm (2.35 in) to the left or right of the left or right V line.

4. ADJUST HEADLIGHT AIM

(a) Adjust the headlight aim vertically:

(1) Using a screwdriver, adjust the aim of each headlight within the specified range by turning the adjusting screw (A).

NOTICE:

The final turn of the adjusting screw must be made clockwise. If the screw is overtightened, loosen it and then retighten it so that the final turn of the screw is clockwise.

HINT:

  • Since the low beams and high beams form one unit, if the low beam aim is correct, the high beam aim is also correct. However, check both sides to be certain.
  • When adjusting the vertical aim of the headlight, the horizontal aim also changes. First adjust the vertical position, then correct the horizontal position.
  • If the headlight aim cannot be adjusted correctly, check the installation of the headlight unit and the headlight unit lens.
  • Check the direction of rotation of the adjusting screw by observing it while tightening. Depending on the screwdriver position, the direction of rotation of the adjusting screw may differ from the direction of rotation of the screwdriver used to tighten it.

*a

Adjusting screw (B)

(b) Adjust headlight aim horizontally:

(1) Using a screwdriver, adjust the aim of each headlight within the specified range by turning the adjusting screw (B).

NOTICE:

The final turn of the adjusting screw must be made clockwise. If the screw is overtightened, loosen it and then retighten it so that the final turn of the screw is clockwise.

HINT:

  • Since the low beams and high beams form one unit, if the low beam aim is correct, the high beam aim is also correct. However, check both sides to be certain.
  • If the headlight aim cannot be adjusted correctly, check the installation of the headlight unit and the headlight unit lens.
  • Check the direction of rotation of the adjusting screw by observing it while tightening. Depending on the screwdriver position, the direction of rotation of the adjusting screw may differ from the direction of rotation of the screwdriver used to tighten it.

*a

Adjusting screw (A)