Maintenance

Replacement

4steps
~24min
2/5difficulty
0102030405011N·mlb·ft
Tightening torque found on this page
Done 0 of 4

REPLACEMENT

PROCEDURE

1. REMOVE NO. 1 ENGINE UNDER COVER

Click here

2. DRAIN ENGINE COOLANT

CAUTION:

  • When the engine coolant is hot, do not remove the reservoir cap, air bleed valve or radiator drain cock plug.
  • Coolant and steam may spray out due to high pressure, causing burns.

    *1

    Reservoir cap

    *2

    Radiator drain cock plug

    *3

    Air bleed valve

    -

    -

(a) Connect a 9 mm (0.354 in.) inside diameter hose to the radiator drain cock, as shown in the illustration.

*a

Hose

(b) Loosen the radiator drain cock plug.

(c) Remove the reservoir cap. Then drain the engine coolant.

*1

Reservoir cap

*2

Radiator drain cock plug

*3

Air bleed plug

*4

Air bleed valve

HINT:

Collect the engine coolant in a container and dispose of it in accordance with local regulations.

(d) Disconnect the hose from the radiator drain cock.

3. ADD ENGINE COOLANT

(a) Using a 6 mm hexagon socket wrench, remove the air bleed valve from the radiator reservoir tank assembly.

*a

Air bleed valve

(b) Connect a 7 mm (0.276 in.) inside diameter hose to the air bleed plug, as shown in the illustration.

HINT:

Use a suitable container to collect the engine coolant.

*1

Air bleed plug

*a

Hose

*b

Container

(c) Loosen the air bleed plug.

(d) Add engine coolant to the reservoir tank assembly until coolant overflows from the air bleed plug hole. Then tighten the air bleed plug.

Torque:

1 N·m {10 kgf·cm, 9 in·lbf}

(e) Squeeze the No. 1 and No. 2 radiator hoses by hand several times, then check the engine coolant level.

If the engine coolant level is low, add engine coolant.

(f) Add engine coolant up to the level shown in the illustration.

Standard capacity:

5.7 liters (6.1 US qts, 5.1 Imp. qts)

NOTICE:

Do not replace the engine coolant with plain water.

HINT:

TOYOTA vehicles are filled with TOYOTA SLLC coolant at the factory. To avoid damage to the engine cooling system and other technical problems, use only TOYOTA SLLC coolant or a similar high-quality ethylene glycol coolant that contains no silicates, amines, nitrites or borates, and that meets the long-life hybrid organic acid technology (HOAT) standard, which combines low phosphate content with low organic acid content.

(g) Using a 6 mm hexagon socket wrench, reinstall the air bleed valve on the radiator reservoir tank assembly.

Torque:

2 N·m {20 kgf·cm, 18 in·lbf}

(h) Reinstall the reservoir cap.

NOTICE:

Tighten the reservoir cap as tightly as possible.

(i) Bleed air from the cooling system.

NOTICE:

  • Before starting the engine, set the A/C switch to OFF.
  • Set the heater control to the maximum position.
  • Set the blower speed to the lowest position.

(1) Warm up the engine until the thermostat opens. Once the thermostat is open, circulate the engine coolant for several minutes.

HINT:

Thermostat opening can be confirmed by squeezing the No. 2 radiator hose by hand and feeling for vibration when the engine coolant begins to flow into the No. 2 radiator hose.

(2) After warming up the engine, run it according to the following cycle for 7 minutes: at 3,000 rpm for 5 seconds, then at idle for 45 seconds (repeat this cycle at least 8 times).

(3) Squeeze the No. 1 and No. 2 radiator hoses by hand several times to bleed air from the system.

Squeeze the No. 1 radiator hose and No. 2 radiator hose:
  • Wear protective gloves.
  • Be careful, as the No. 1 and No. 2 radiator hoses are hot.
  • Keep hands away from the fan.

NOTICE:

  • If the coolant temperature gauge indicates excessive temperature, stop the engine and let it cool down.
  • Make sure the intercooler reservoir tank assembly still contains engine coolant.
  • If the reservoir tank assembly does not have enough engine coolant, the engine may overheat or be severely damaged.
  • If the reservoir tank assembly does not have enough engine coolant, do the following: 1) stop the engine, 2) wait until the engine coolant has cooled, and 3) add engine coolant up to the FULL line of the reservoir tank assembly.

HINT:

If the sound of engine coolant flowing can still be heard after bleeding air, perform the following air bleeding procedure again.

  1. Warm up the engine. (While the engine is idling, make sure engine coolant flows into the reservoir tank assembly.)
  2. Run the engine at 2,000 rpm for at least 2 minutes. (A)
  3. Let the engine idle for at least 2 minutes. (B)
  4. Repeat steps (A) and (B) at least 4 times.

(j) Once the engine has cooled, check that the coolant level is between the FULL and LOW lines.

NOTICE:

The coolant levels in the compartments inside the radiator reserve tank assembly may differ. This is not a malfunction.

If the engine coolant level is below the LOW line, add engine coolant up to the FULL line.

*a

FULL line

*b

LOW line

4. CHECK FOR POSSIBLE COOLANT LEAK

Click here

5. INSTALL ENGINE UNDER COVER NO. 1

Click here