Suspension System

Description and Operation

32steps
~192min
4/5difficulty
02040608010053.940N·mlb·ft
Tightening torque found on this page
Done 0 of 32

Contents:

Description and Operation

Description

  • Wheel alignment is all forces due to friction, gravity, centrifugal force and inertia operate in a balanced manner while driving.
  • Wheel alignment improves linearity, grounding performance, tire life extension and fuel reduction and ensures safety at high speeds.
  • Alignment adjustments consist of camber, castor, kingpin angle, toe, left, thrust angle, etc.

Components

Camber Camber refers to the angle at which the top of the wheel is tilted inward or outward relative to the vertical line started from the center of the floor when the vehicle is viewed from the front.
  • It facilitates steering control of the steering wheel and prevents bending of the front axle.
( + ) Camber It is a camber form with wheels tilted outward from the top. It prevents the underside of the wheel from opening, so there is less tire wear due to unnecessary driving resistance on curves. ( - ) Camber It is a camber form with wheels tilted inward from the top. cause strong friction when driving curves but tires are prone to wear. Caster Caster refers to the angle at which the steering shaft tilts forward and backward relative to the vertical line initiated from the center of the wheel floor when the vehicle is viewed from the side.
  • It gives a straight line to the steering wheel when driving.
  • Provides resilience to wheels when steering.
  • It prevents shaking of wheels while driving.
King pin angle Kingpin angle refers to the angle at which the centerline of the steering shaft and the bottom vertical line forms when the vehicle is viewed from the front.
  • Provides easy steering of the steering wheel and resilience of the steering wheel.
  • The kingpin angle and camber are also called Included Angle (I.A.). [Included Angle (I.A.)]
Item Descriptions
A Steering Center Line
B Kingpin
C Center Line

Toe Toe is the tilted angle or distance at the front of the wheel when looking up and down at the vehicle.
  • The state in which the front of the wheel faces outward is called Toe out, and the state in which the front of the wheel faces inward is called Toe in.
  • In general vehicles, toe-in is applied to prevent side slip. A phenomenon in which the wheels slide sideways due to the influence of the camber while the vehicle is driving.
  • Tow-out is sometimes applied to vehicles that require a fast steering response when turning.
Set Back Set back refers to the angle at which the line connects the center of the front wheels from the line perpendicular to the vehicle's centerline.
  • The main cause of the set back is the presence of an accident in the vehicle or an abnormality in the body.
Thrust angle The angle at which the Thrust line and the centerline of the vehicle are formed. ※Thrust line: line that is perpendicular to the center line of the rear axle.
  • Thrust conditions occur when the rear wheel individual toe is not the same.
Poor thrust angles can increase tire wear, reduce steering direction, and cause dog tracking. ※Dog tracking: The driving condition when the thrust line is not parallel to the center line of the vehicle

On Vehicle Inspection

On Vehicle Inspection

Driving test Carry out pre-work vehicle driving tests to check vehicle behavior under normal driving conditions.

On straight, flat road

  1. Check that the vehicle is going straight when release the steering wheel.
  2. Check that the vehicle pulls to one side while accelerating and braking.

Stop and Go

  1. Check that the vehicle pulls to one side while accelerating and braking.
  2. Check that the vehicle pulls to one side while accelerating or decelerating.
  3. Check the part for noise or abnormal movement.

Turning left or right

  1. Turn the steering wheel and check if it returns when released.
  2. Check if the vehicle is pulls in the direction in which the steering wheel was last turned.
  3. Check the part for noise or abnormal movement.

Deflected or protruded road

  1. Check if the vehicle changes direction.
  2. Check the part for noise or abnormal movement.
  3. Check if the vehicle is over-bouncing.
Tire Wear Inspection
Wheel and tire diagnosis
Rapid wear at the center Rapid wear at both shoulders Wear at one shoulder
  • Poor installing of tire
  • Over inflated tires
  • Under-inflated tires
  • Excessive rapid acceleration
  • Poor installing of tire
  • Too low amount of tire air pressure
  • Damaged suspension components
  • Excessive cornering speeds
  • Too low amount of tire air pressure
  • Under-inflated tires
  • Camber out of specification
  • Damaged suspension components
Partial wear Feathered edge Diagonal wear
  • Damaged or worn brake discs
  • Excessive sudden acceleration, sudden braking
  • Damaged suspension components
  • Too low amount of tire air pressure
  • Under-inflated tires
  • Damaged tie rod
  • Damaged knuckle
  • Under-inflated tires
  • Camber out of specification
  • Damaged suspension components

Inspect steering system related parts
  1. Check the universal joint for tightening, wear, damage and rust.
  2. Check that the mounting is loose by moving the steering gearbox up and down, and if damaged, replace it.
  3. Check the steering gearbox housing for abnormalities.
  4. Check each suspension bushing for wear, cracks, etc.
  5. Check the strut and shock absorber for damage.
  6. Check the ride height.
  7. Check the coil spring for damage or wear.
  8. Check the lower arm ball joint for damage or free play.
Inspect suspension system related parts

Repair procedures

Wheel Alignment Repair Procedures

  1. When using the wheel alignment tester to check the wheel alignment, align the lift's vehicles horizontally.
  2. Set the transmission gear to 'N'.
  3. Inflate the 4 tires to the specified tire pressure. Tire Pressure
    Tire Front Rear
    235/55 R19 250 - 255 kPa (36 - 37 psi)
    255/45 R20
  4. Check the steering wheel and tires aligning straight.
  5. Hold the brake pedal depressed using a pedal stopper.
  6. Measure the ride height, which is the distance from the end of the fender to the center of the wheel. Ride Height :
    Front (A) : 426 - 446 mm (16.77 - 17.55 in.) Rear (B) : 439 - 459 mm (17.28 - 18.07 in.)
  7. Adjust the alignment to the specification. (Refer to Alignment - "Adjustment")
    Make sure to adjust the rear alignment first with curb weight and then adjust the front alignment by referring to the thrust angle.
  8. After adjusting, shake the vehicle and check if the alignment value returns.
    If the value changes significantly, check the suspension for free play or bushing damage and wear.
  9. Perform the order below with the KDS. (S/W Management → EPS - Power Steering → SAS Calibration)
    Refer to the KDS screen for operating conditions and details

Adjustment

Adjustment

[Rear] Remove the fasteners, and then separate the service cover (A) in the direction of the arrow to adjust rear alignment.

Toe

Turn the cam bolt (A) attached with the rear assist arm clockwise or counterclockwise to adjust the toe. Adjust the left and right cam bolts to the same amount.

Total Toe : 0.0 - 0.4° Individual : 0.0 - 0.2°

Cam bolt Rotation Descriptions
RH Clockwise Toe in
LH Clockwise Toe out

Adjust the toe using total toe.

Camber

Turn the cam bolts (A) attached with the rear lower arm clockwise or counterclockwise to adjust the camber.

Camber Angle : -1.5 to -0.5°

Cam bolt Rotation Descriptions
RH Clockwise - Camber
LH Clockwise + Camber

Thrust angle

Thrust angle : -0.1 - 0.1°

[Front]

Toe

Toe is adjusted by rotation of the tie rod rotation buckle. Turning the tie rod to the rear of the vehicle will reduce the toe on the front wheels. The adjustment toe is adjusted by turning the left and right tie rods to the same value.

Total Toe : -0.1 - 0.3° Individual : -0.05 - 0.15°

  1. Loosen the tie rod end nut (A) until the toe can be adjusted.

    Tightening torque : 49.0 - 54 N·m

  2. Hold the tie rod end (A) using a wrench to prevent the tie rod from turning when adjusting alignment.
  3. Adjust the toe in the specified value by turning the tie rod turn buckle (A).
    After toe adjustment, the visible number of threads on the left and right should be equal.
  4. After adjustment, tighten the tie rod end nut (A) to specification torque.

    Tightening torque : 49.0 - 54 N·m

  • Be careful not to twist the bellows boot when adjusting the toe.
  • After toe adjustment, adjust the tie rod end position horizontally to ensure that the ball joint boot (A) is not pressed.

Camber

The camber cannot be adjusted. If the measured camber exceeds the standard limit, repair or replace the relevant parts and inspect the wheel alignment again.

Camber Angle : -1.07 to -0.07°

Item Description
A Camber Angle
B Center Line

Caster

The caster cannot be adjusted. If the measured caster exceeds the standard limit, repair or replace the relevant parts and inspect the wheel alignment again.

Caster Angle : 5.23 - 6.23°

  • Before measuring the front wheel alignment, wear, loose and damaged parts of the front suspension assembly should be replaced.
  • Camber and caster are assembled at the specified value during production and need not be adjusted.
  • If the camber and caster are not within the specified limits, replace the bent or damaged parts.
  • The difference between the left and right wheels of Camber and Caster shall be within 0° ± 0.5°.

Kingpin

The king pin angle cannot be adjusted. If the measured kingpin exceeds the standard limit, repair or replace the relevant parts and inspect the wheel alignment again.

King Pin Angle : 13.22 - 14.22°

Item Description
A Steering Center Line
B Kingpin
C Center Line

Set back

Setback cannot be adjusted, but the value is useful for diagnosing central steering problems, such as tilting. After repairing a vehicle with a damaged frame, the set-back must be checked. The ideal setback value should be zero.