Suspension System
Front Suspension System
In this manual: Suspension System
55steps
~330min
4/5difficulty
Done 0 of 55
Contents:
Components and Components Location. Front Strut Assembly Components and Components Location
Components and Components Location
Components and Components Location
| 1. Front Strut Assembly 1-a. 53.9 - 74 N·m 1-b. 156.9 - 176 N·m 2. Front Sub Frame 2-a. 112.8 - 123 N·m + 85 - 95° 3. Front Sub Frame Bar 3-a. 166.7 - 186 N·m 4. Front Lower Arm 4-a. 117.7 - 137 N·m 4-b. 156.9 - 176 N·m |
5. Front Stabilizer Bar Link 5-a. 98.1 - 118 N·m 6. Front Stabilizer Bar 6-a. 53.9 - 64 N·m 7. Front Lower Arm Ball Joint 7-a. 98.1 - 118 N·m |
Front Strut Assembly Components and Components Location
Components and Components Location
| 1. Insulator Cap 2. Insulator Assembly 2-a. 53.9 - 74 N·m 3. Strut Bearing 4. Bumper Stopper |
5. Dust Cover 6. Coil Spring 7. Spring Lower Pad 8. Strut Assembly 8-a. 117.7 - 128 N·m |
Front Strut Assembly Removal and Installation
Removal
- Remove the front strut upper mounting nuts (A).
Tightening torque : 53.9 - 74 N·m
- Remove the front wheel and tires. (Refer to Wheel and Tire - "Wheel")
- Remove the brake hose bracket (A) after removing the bolt.
Tightening torque : 19.6 - 29 N·m
- Remove the stabilizer bar link (A) from the front strut assembly after removing the nut.
Tightening torque : 98.1 - 118 N·m
- Hold the outer hex (A) when removing or installing the nut (B).
- Be careful not to damage the boot of the link.
- Use a hand tool when removing or installing the stabilizer bar link nut.
- Remove the front strut assembly (A) from the front axle after removing the bolts and nuts.
Tightening torque : 156.9 - 176 N·m
Installation
- Install in the reverse order of removal.
Pre-tighten the front strut upper nuts and put the vehicle down on the ground and tighten the front strut upper nuts to tightening torque value.
Front Strut Assembly Disassembly
Special Service Tool
| Tool Name / Number | Illustration | Description |
| Shock absorber lock nut remover. 0K546 - F6100 |
Used for removal or installing of front strut lock nut. |
Disassembly
- Remove the front strut assembly. (Refer to Front Suspension System - "Front Strut Assembly")
- Install the front strut assembly (A) to the spring compressor.
- Remove the insulator cap (A).
- Compress the coil spring (A) slightly until it is tensioned using the spring compressor.
Protect the coil spring when compressing using rubber such as plastic hose, etc to prevent the damage. - Remove the nut using the SST (0K546 - F6100).
Tightening torque : 117.7 - 128 N·m
- Disassemble insulator (A), strut bearing (B), bumper stopper (C), dust cover (D), coil spring (E), spring lower pad (F) from the strut (G).
Front Strut Assembly Inspection
Inspection
- Check the strut insulator bearing for wear and damage.
- Check the rubber parts for damage and deterioration.
- Compress and extend the piston rod (A) and check that there is no abnormal resistance or unusual sound during operation.
Disposal
- Fully extend the strut rod.
- Drill a hole in the (A) area of the cylinder to deflate gas.
The gas coming out is harmless, but be careful of debris that may fly when drilling.
Front Strut Assembly Reassembly
Special Service Tool
| Tool Name / Number | Illustration | Description |
| Shock absorber lock nut remover. 0K546 - F6100 |
Used for removal or installing of front strut lock nut |
Reassembly
- Assemble the insulator (A), strut bearing (B), bumper stopper (C), dust cover (D), coil spring (E), and spring lower pad (F) on the strut (G).
- Align the protrusions of the strut bearing upper housing and the lower housing when reassembling.
- Align the protrusion of the insulator (A) and groove of the bearing (B) when assembling.
- When installing insulator assembly to the front strut assembly, align the protrusion (A) of the strut bearing and knuckle mounting parts (B).
- When installing the coil spring, make sure that the gap (A) between the spring top start and 180° past point (B) and the spring upper pad is within the allowable value.
Allowable clearance (A) : 3 mm (0.1181 in.)
- Install the front strut assembly (A) to the spring compressor.
- Compress the coil spring (A) slightly until it is tensioned using the spring compressor.
Protect the coil spring when compressing using rubber such as plastic hose, etc to prevent the damage. - Install the self locking nut using SST (0K546 - F6100).
Tightening torque : 117.7 - 128 N·m
Do not reuse the self locking nut. - Install the insulator cap (A).
- Install the front strut assembly. (Refer to Front Suspension System - "Front Strut Assembly")
Front Lower Arm Removal and Installation
Special Service Tool
| Tool Name / Number | Illustration | Description |
| Lower arm ball joint remover 0K545 - A9100 |
Used for removal of front lower arm ball joint |
Removal
[Front Lower Arm Ball Joint]- Remove the front wheel and tires. (Refer to Wheel and Tire - "Wheel")
- Remove the front under cover. (Refer to Motor and Reduction Gear System - "Front Under Cover")
- Separate the lower arm ball joint from the front axle using SST (0K545 - A9100).
- Remove the split pin (D).
- Remove the lower arm bolt (A), washer (B), and nut (C).
Tightening torque : 98.1 - 118 N·m
Hold the lower arm ball joint bolt and remove or install the nut. - Do not reuse the split pin.
- Be careful not to change the position of the bolt, nut, and washer when installing.
- Place the support bolts (A) to the lower arm ball joint mounting hole, and then rotate them to install the SST.
Use the support body (A) of the SST (0K545 - A9100). - Install the support body (B) in the front axle groove (A).
- Rotate the bolt (A) to insert the support body (B) to release the front knuckle.
- Install the main body (A) between the front strut assembly and front lower arm.
Use the main body (A) of the SST (0K545 - A9100). - Secure the main body with the wire (A) to prevent it from falling.
- Install the c-clamp (A) by rotating the handle (B) to prevent the main body from slipping.
Use the C-clamp (A) of the SST (0K545 - A9100). - Tighten the bolt (A) to widen the gap of the main body so that the front lower arm can be removed from the front knuckle.
- Remove the lower arm ball joint (A) after removing the nuts.
Tightening torque : 98.1 - 118 N·m
- Remove the front wheel and tires. (Refer to Wheel and Tire - "Wheel")
- Separate the lower arm ball joint from the front axle using SST (0K545 - A9100).
- Remove the split pin (D).
- Remove the lower arm bolt (A), washer (B), and nut (C).
Tightening torque : 98.1 - 118 N·m
Hold the lower arm ball joint bolt and remove or install the nut. - Do not reuse the split pin.
- Be careful not to change the position of the bolt, nut, and washer when installing.
- Place the support bolts (A) to the lower arm ball joint mounting hole, and then rotate them to install the SST.
Use the support body (A) of the SST (0K545 - A9100). - Install the support body (B) in the front axle groove (A).
- Rotate the bolt (A) to insert the support body (B) to release the front knuckle.
- Install the main body (A) between the front strut assembly and front lower arm.
Use the main body (A) of the SST (0K545 - A9100). - Secure the main body with the wire (A) to prevent it from falling.
- Install the c-clamp (A) by rotating the handle (B) to prevent the main body from slipping.
Use the C-clamp (A) of the SST (0K545 - A9100). - Tighten the bolt (A) to widen the gap of the main body so that the front lower arm can be removed from the front knuckle.
- Remove the front lower arm (C) after removing the bolts, nut, and washer.
Tightening torque : (A) :117.7 - 137 N·m (B) :156.9 - 176 N·m
Installation
- Install in the reverse order of removal.
- Check the alignment. (Refer to Alignment - "Repair Procedures")
Front Lower Arm Inspection
Inspection
- Check the bushing for wear or aging.
- Check the lower arm for bent or damaged.
- Check all bolts.
Front Lower Arm Replacement - Lower Arm 'G' Bushing
Special Service Tool
| Tool Name / Number | Illustration | Description |
| Lower arm 'G' bushing replacement tool 09545 - AL100 |
Used for replacement of the lower arm 'G' bushing |
Replacement - Lower Arm 'G' Bushing
| Replace the lower arm 'G' bushing if it only has a crack, noise from bushing without cracks can be improved by applying silicone oil. |
- Replace the lower arm 'G' bushing by using the SST (09545 - AL100).
Refer to the enclosed manual for detailed usage instructions. - Wear personal protective equipment during press operation.
- When the press is in operation, ensure that no part of the body comes into contact within the operating range.
- Due to the risk of injury from falling tools and parts, before operating the press, ensure that all tools and components are securely positioned in their proper places.
- Lubricate the bushings and mounting surface with grease during the operation.
- Measure the void spacing (A), (B) to ensure that the bushing can be properly installed in the correct direction.
(A) : Ball joint side (B) : Opposite side
- Refer to the enclosed manual for void spacing specifications for each vehicle model.
- There may be no difference in void spacing for used bushing due to wear.
- Be careful not to install the bushing at the incorrect angle.
Installaion angle (A) : Angle formed counterclockwise from 'A' bushing (B) and 'G' bushing (C) reference
Refer to the enclosed manual for installation angle specifications for each vehicle model. - Clean the bushing mounting surface (A) from any foreign substances using a clean cloth or similar material when installing.
- Ensure that the marking angle (A) of the bushing and the lower arm does not deviate from the reference value.
Reference Value : ± 3°
- If excessive pressure is applied after installation is complete, it may result in damage to the components and tools.
Front Stabilizer Bar Removal and Installation
Removal
[Front Stabilizer Bar Link]- Remove the front wheel and tires. (Refer to Wheel and Tire - "Wheel")
- Remove the stabilizer bar link (A) from the front strut assembly after removing the nut.
Tightening torque : 98.1 - 118 N·m
- Hold the outer hex (A) when removing or installing the nut (B).
- Be careful not to damage the boot of the link.
- Use a hand tool when removing or installing the stabilizer bar link nut.
- Remove the stabilizer bar link (A) from the stabilizer bar after removing the nut.
Tightening torque : 98.1 - 118 N·m
- Hold the outer hex (A) when removing or installing the nut (B).
- Be careful not to damage the boot of the link.
- Use a hand tool when removing or installing the stabilizer bar link nut.
- Remove the front wheel and tires. (Refer to Wheel and Tire - "Wheel")
- Remove the front under cover. (Refer to Motor and Reduction Gear System - "Front Under Cover")
- Remove the stabilizer bar link (A) from the stabilizer bar after removing the nut.
Tightening torque : 98.1 - 118 N·m
- Hold the outer hex (A) when removing or installing the nut (B).
- Be careful not to damage the boot of the link.
- Use a hand tool when removing or installing the stabilizer bar link nut.
- Remove the front wheel guard. (Refer to Body - "Wheel Guard")
- Remove the front stabilizer bar (A) after removing the bolts.
Tightening torque : 53.9 - 64 N·m
[LH] [RH]
Installation
- Install in the reverse order of removal.
- Check the alignment. (Refer to Alignment - "Repair Procedures")
Front Stabilizer Bar Inspection. Front Stabilizer Bar Disassembly and Reassembly
Front Stabilizer Bar Inspection
Inspection
- Check the stabilizer bar bushing for damage.
- Check the stabilizer bar link ball joint for damage.
Front Stabilizer Bar Disassembly and Reassembly
Disassembly
- Remove the stabilizer bar bushing bracket (A) using a flat-head screwdriver or suitable tool.
Take care not to deform when removing and replace if deformed. - Remove the stabilizer bar bushing (A).
Do not reuse the stabilizer bar bushing (A).
Reassembly
- Reassemble in the reverse order of disassembly.
Front Subframe Removal and Installation - 2WD ➤
Front Subframe Removal and Installation - 4WD
Removal
|
- Remove the front motor and reduction gear assembly. (Refer to Front Motor and Reduction Gear System - "Front Motor and Reduction Gear Assembly")
- Remove the mounting bracket (A) after removing the bolts.
Tightening torque : 63.7 - 83 N·m
- Remove the steering gear box (A) after removing the bolts.
Tightening torque : 107.9 - 128 N·m
When installing the steering gear box, pre-tighten all bolts and tighten to the specified torque. - Remove the front stabilizer bar (A) after removing the bolts.
Tightening torque : 53.9 - 64 N·m
- Remove the front lower arm (A) after removing the bolts, nuts, and washers.
Tightening torque : (B) : 117.7 - 137 N·m (C) : 156.9 - 176 N·m
Installation
|
- Install in the reverse order of removal.
- Check the alignment. (Refer to Alignment - "Repair Procedures")
Was this page helpful?