Suspension System

Components and Components Location. Rear Shock Absorber Components and Components Location

90steps
~540min
4/5difficulty
060120180240300196.1145N·mlb·ft
Tightening torque found on this page
Done 0 of 90

Contents:

Components and Components Location. Rear Shock Absorber Components and Components Location

Components and Components Location

Components and Components Location

1. Rear Coil Spring Upper Pad
2. Rear Coil Spring
3. Rear Coil Spring Lower Pad
4. Rear Lower Arm
4-a. 176.5 - 196 N·m
4-b. 137.3 - 157 N·m
5. Rear Assist Arm
5-a. 117.7 - 137 N·m
5-b. 137.3 - 157 N·m
6. Rear Shock Absorber
6-a. 117.7 - 137 N·m
7. Rear Upper Arm - Front
7-a. 156.9 - 176 N·m
8. Rear Upper Arm - Rear
8-a. 176.5 - 196 N·m
9. Trailing Arm
9-a. 117.7 - 137 N·m
10. Rear Stabilizer Bar
10-a. 49 - 64 N·m
11. Rear Stabilizer Bar Link
11-a. 98.1 - 118 N·m
12. Rear Cross Member
12-a. 112.8 - 123 N·m + 85 - 95°

Rear Shock Absorber Components and Components Location

Components and Components Location

1. Insulator Cap
2. Insulator
2-a. 117.7 - 137 N·m
3. Bumper Stopper
4. Dust Cover
5. Shock Absorber Assembly
5-a. 19.6 - 24 N·m

Rear Shock Absorber Removal and Installation

Removal

  1. Remove the rear wheel and tires. (Refer to Wheel and Tire - "Wheel")
  2. Remove the rear shock absorber lower bolt (A), washer (B), and nut (C).

    Tightening torque : 176.5 - 196 N·m

    If using a transmission jack to support a reduction gear, do not lift the vehicle too much. The center gravity of the vehicle may change and fall.
    • Install the transmission jack and lift up the parts to prevent the bolts and nuts from damage when installing or removing.
    • Mark and remove all bolts and nuts to prevent incorrectly positioned installation.
  3. Remove the rear shock absorber (A) after removing the bolts.

    Tightening torque : 117.7 - 137 N·m

    Hold the bolt and remove or install the nut.

Installation

  1. Install in the reverse order of removal.

Rear Shock Absorber Disassembly

Special Service Tool

Tool Name / Number Illustration Description
Shock absorber lock nut remover.
09546 - 3X100
Used for removal or installing of rear shock absorber lock nut.

Disassembly

  1. Remove the rear shock absorber. (Refer to Rear Suspension System - "Rear Shock Absorber")
  2. Remove the insulator cap (A).
  3. Remove the rear shock absorber lock nut using the SST(09546 - 3X100).

    Tightening torque : 16.7 - 24 N·m

  4. Disassemble the insulator (A), bumper rubber (B), dust cover (C).

Rear Shock Absorber Inspection

Inspection

  1. Check the rubber parts for damage or deterioration.
  2. Check all bolts and nuts.
  3. Repeat compression and tension of the rear shock absorber rod (A) to check for abnormal resistance or noise between operations.

Disposal

  1. Fully extend the rear shock absorber rod.
  2. Drill the (A) of the cylinder to deflate gas.
    The gas coming out is harmless, but be careful of debris that may fly when drilling.
    Wear protective glasses to prevent injury from drill chips when drilling.

Rear Shock Absorber Reassembly

Special Service Tool

Tool Name / Number Illustration Description
Shock absorber lock nut remover.
09546 - 3X100
Used for removal or installing Rear shock absorber [None ECS] lock nut

Reassembly

  1. Reassemble the insulator (A), bumper rubber (B), dust cover (C) to the shock absorber.
  2. Install the rear shock absorber lock nut using the SST(09546 - 3X100).

    Tightening torque : 16.7 - 24 N·m

    Do not reuse the lock nut.
  3. Install the insulator cap (A).
  4. Install the rear shock absorber. (Refer to Rear Suspension System - "Rear Shock Absorber")

Rear Coil Spring Removal and Installation

Removal

  • When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
  • When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
  • If using a transmission jack to support a reduction gear, do not lift the vehicle too much. The center gravity of the vehicle may change and fall.
  1. Remove the rear wheel and tires. (Refer to Wheel and Tire - "Wheel")
  2. Remove the rear shock absorber lower bolt (A), washer (B), and nut (C).

    Tightening torque : 176.5 - 196 N·m

    • Install the transmission jack and lift up the parts to prevent the bolts and nuts from damage when installing or removing.
    • Mark and remove all bolts and nuts to prevent incorrectly positioned installation.
    Hold the bolt and remove or install the nut.
  3. Remove the rear lower arm nut (A), washer (B), and bolt (C).

    Tightening torque : 176.5 - 196 N·m

    • Install the transmission jack and lift up the parts to prevent the bolts and nuts from damage when installing or removing.
    • Mark and remove all bolts and nuts to prevent incorrectly positioned installation.
    Hold the bolt and remove or install the nut.
  4. Lower the rear lower arm in the direction of the arrow, then remove the rear coil spring (A).
  5. Remove the rear coil spring lower pad (A) from the rear lower arm.

Installation

  • When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
  • When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
  • If using a transmission jack to support a reduction gear, do not lift the vehicle too much. The center gravity of the vehicle may change and fall.
  1. Install in the reverse order of removal.
    • After installation, check the prostrusion (A) on the top of the rear lower arm and reinstall the lower arm pad if the prostrusion (A) is not fully exposed.
    • When installing the rear coil spring, mount it so that the surface (A) of the lower pad of the spring and the end of the spring (B) contact as much as possible.

      Maximum allowable gap : 3 mm (0.1181 in.)

  2. Check the alignment. (Refer to Alignment - "Repair Procedures")

Rear Coil Spring Inspection

Inspection

  1. Check the coil spring for cracks or deformation.
  2. Check the coil spring pad for damage and deformation.

Rear Upper Arm Removal and Installation

Removal

  • When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
  • When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
  • If using a transmission jack to support a reduction gear, do not lift the vehicle too much. The center gravity of the vehicle may change and fall.
[Rerar Upper Arm - Front]
  1. Remove the rear crossmember. (Refer to Rear Suspension System - "Rear Crossmember")
  2. Remove the rear upper arm - front (A) after removing the bolt and nut.

    Tightening torque : 156.9 - 176 N·m

    Mark and remove all bolts and nuts to prevent incorrectly positioned installation.
    Hold the bolt and remove or install the nut.
  3. Remove the rear wheel and tires. (Refer to Wheel and Tire - "Wheel")
  4. Separate the rear wheel speed sensor bracket (A) after removing the bolt and washer.

    Tightening torque : 19.6 - 29 N·m

    • Install the transmission jack and lift up the parts to prevent the bolts and nuts from damage when installing or removing.
    • Mark and remove all bolts and nuts to prevent incorrectly positioned installation.
    Hold the bolt and remove or install the nut.
  5. Remove the rear upper arm - rear bolt (A) and nut (B).

    Tightening torque : 176.5 - 196 N·m

    • Install the transmission jack and lift up the parts to prevent the bolts and nuts from damage when installing or removing.
    • Mark and remove all bolts and nuts to prevent incorrectly positioned installation.
    Hold the bolt and remove or install the nut.
  6. Remove the rear upper arm - rear (A) after removing the bolt, nut, and washer.

    Tightening torque : 156.9 - 176 N·m

    • Install the transmission jack and lift up the parts to prevent the bolts and nuts from damage when installing or removing.
    • Mark and remove all bolts and nuts to prevent incorrectly positioned installation.
    Hold the bolt and remove or install the nut.
[Rear Upper Arm - Rear]

Installation

  • When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
  • When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
  • If using a transmission jack to support a reduction gear, do not lift the vehicle too much. The center gravity of the vehicle may change and fall.
  1. Install in the reverse order of removal.
  2. Check the alignment. (Refer to Alignment - "Repair Procedures")

Rear Upper Arm Inspection

Inspection

  1. Check the bushing for wear and aging.
  2. Check the rear upper arm for bent or damage.
  3. Check all bolts and nuts.

Rear Lower Arm Removal and Installation

Removal

  1. Remove the rear under cover. (Refer to Motor and Reduction Gear System - "Rear Under Cover")
  2. Remove the rear coil spring. (Refer to Rear Suspension System - "Rear Coil Spring")
  3. Remove the rear lower arm (A) after removing the cam bolt, nut, and plate.

    Tightening torque : 137.3 - 157 N·m

    • Install the transmission jack and lift up the parts to prevent the bolts and nuts from damage when installing or removing.
    • Mark and remove all bolts and nuts to prevent incorrectly positioned installation.
    Hold the bolt and remove or install the nut.

Installation

  1. Install in the reverse order of removal.
    When tightening the nut, align the center of the bolt plate scale with the center of the guide.
  2. Check the alignment. (Refer to Alignment - "Repair Procedures")

Rear Lower Arm Inspection

Inspection

  1. Check the bushing for wear and aging.
  2. Check the rear lower arm for bent or damage.
  3. Check all bolts and nuts.

Rear Assist Arm Removal and Installation

Removal

If using a transmission jack to support a reduction gear, do not lift the vehicle too much. The center gravity of the vehicle may change and fall.
  1. Remove the rear wheel and tires. (Refer to Wheel and Tire - "Wheel")
  2. Remove the rear under cover. (Refer to Motor and Reduction Gear System - "Rear Under Cover")
  3. Remove the rear assist arm cam bolt (A), plate (B) and nut (C).

    Tightening torque : 137.3 - 157 N·m

    • Install the transmission jack and lift up the parts to prevent the bolts and nuts from damage when installing or removing.
    • Becareful not to change the bolt, nut and plate installing position.
    • Use a tool such as the magnetic pickup tool (A) to pick up the cam bolt after removing the cam bolt.
    Hold the bolt and remove or install the nut.
  4. Remove the rear assist arm (A) after removing the bolt, washer and nut.

    Tightening torque : 117.7 - 137 N·m

Installation

  1. Install in the reverse order of removal.
    When tightening the nut, align the center of the bolt plate scale with the center of the guide.
  2. Check the alignment. (Refer to Alignment - "Repair Procedures")

Rear Assist Arm Inspection

Inspection

  1. Check the bushing for wear and aging.
  2. Check the rear assist arm for bent or damage.
  3. Check all bolts.

Trailing Arm Removal and Installation

Removal

If using a transmission jack to support a reduction gear, do not lift the vehicle too much. The center gravity of the vehicle may change and fall.
  1. Remove the rear wheel and tires. (Refer to Wheel and Tire - "Wheel")
  2. Remove the rear under cover. (Refer to Motor and Reduction Gear System - "Rear Under Cover")
  3. Remove the trailing arm bolt (A) and nut (B).

    Tightening torque : 117.7 - 137 N·m

    • Install the transmission jack and lift up the parts to prevent the bolts and nuts from damage when installing or removing.
    • Becareful not to change the bolt, nut and plate installing position.
    Hold the bolt and remove or install the nut.
  4. Remove the trailing arm (A) after removing the bolts.

    Tightening torque : 117.7 - 137 N·m

Installation

  1. Install in the reverse order of removal.
  2. Check the alignment. (Refer to Alignment - "Repair Procedures")

Trailing Arm Inspection

Inspection

  1. Check the bushing for wear and aging.
  2. Check the trailing arm for bent or damage.
  3. Check all bolts and nuts.

Rear Stabilizer Bar Removal and Installation

Removal

[Rear Stabilizer Bar Link]
  1. Remove the rear wheel and tires. (Refer to Wheel and Tire - "Wheel")
  2. Remove the rear stabilizer bar link nut (A).

    Tightening torque : 98.1 - 118 N·m

    • Hold the rear stabilizer bar link outer hex (A), and then remove or install the nut (B).
    • Be careful not to damage the boot of the link.
    • Use a hand tool when removing or installing the rear stabilizer bar link nut.
  3. Remove the rear stabilizer bar link (A) after removing the nut.

    Tightening torque : 98.1 - 118 N·m

    • Hold the rear stabilizer bar link outer hex (A), and then remove or install the nut (B).
    • Be careful not to damage the boot of the link.
    • Use a hand tool when removing or installing the rear stabilizer bar link nut.
[Rear Stabilizer Bar]
  • When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
  • When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
  1. Remove the rear motor and reduction gear aseembly. (Refer to Motor and Reduction Gear System - "Rear Motor and Reduction Gear Assembly")
    Perform only steps 1 - 19, and then follow the next steps to removing the rear stabilizer bar.
  2. Disconnect the connectors (A).
  3. Separate the high-voltage cable wiring (A) after removing the bolts.

    Tightening torque : 16.7 - 24 N·m

  4. Remove the rear stabilizer bar link nut (A).

    Tightening torque : 98.1 - 118 N·m

    • Hold the rear stabilizer bar link outer hex (A), and then remove or install the nut (B).
    • Be careful not to damage the boot of the link.
    • Use a hand tool when removing or installing the rear stabilizer bar link nut.
  5. Remove the rear stabilizer bar (A) after removing the bolts and nuts.

    Tightening torque : 49.0 - 64 N·m

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.
  2. Check the alignment. [When replacing the rear stabilizer bar] (Refer to Alignment - "Repair Procedures")

Rear Stabilizer Bar Inspection

Inspection

  1. Check the stabilizer bar bushing for damage.
  2. Check the stabilizer bar link ball joint for damage.
  3. Check all bolts and nuts.

Rear Crossmember Removal and Installation

Removal

  • When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
  • When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
  1. Remove the rear motor and reduction gear assembly. (Refer to Motor and Reduction Gear System - "Rear Motor and Reduction Gear Assembly")
  2. Remove the stabilizer bar link (A) after removing the nut.

    Tightening torque : 98.1 - 118 N·m

  3. Remove the rear upper arm - rear (A) after removing the bolt, washer and nut.

    Tightening torque : 156.9 - 176 N·m

  4. Remove the trailing arm nut (A) and bolt (B).

    Tightening torque : 117.7 - 137 N·m

  5. Remove the rear carrier (A) after removing the bolt, washer and nut.

    Tightening torque : 117.7 - 137 N·m

  6. Remove the rear stabilizer bar (A) after removing the bolts and nuts.

    Tightening torque : 49.0 - 64 N·m

  7. Remove the trailing arm (A) after removing the bolts.

    Tightening torque : 117.7 - 137 N·m

  8. Remove the rear upper arm - rear (A) after removing the bolts and nuts.

    Tightening torque : 176.5 - 196 N·m

  9. Remove the rear upper arm - front (A) after removing the bolts and nuts.

    Tightening torque : 156.9 - 176 N·m

  10. Remove the rear assist arm (A) bolts, plates and nuts.

    Tightening torque : 137.3 - 157 N·m

  11. Remove the rear lower arm (A) after removing the bolts, plates and nuts.

    Tightening torque : 137.3 - 157 N·m

Installation

  • When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
  • When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
  1. Install in the reverse order of removal.
    When tightening the nut, align the center of the bolt plate scale with the center of the guide. [Rear Assist Arm] [Rear Lower Arm]
  2. Check the alignment. (Refer to Alignment - "Repair Procedures")

Rear Crossmember Inspection

Inspection

  1. Check the bushing for wear or aging.
  2. Check all bolts and nuts.