Suspension System
Wheel and Tire
In this manual: Suspension System
19steps
~114min
4/5difficulty
Done 0 of 19
Contents:
Tire Inspection
Tire Wear
- Measure the tread depth of the tires.
Tread depth [Limit] : 1.6 mm (0.062 in.) (High Speed Vehicle : 2.4 mm (0.09 in.) - If the remaining tread depth (A) is less than the limit, replace the tire.
If the tread depth is less than 1.6 mm (High Speed Vehicle: 2.4 mm (0.09 in.) the wear indicator (B) appears.
Tire Removal
Removal
- Remove the wheels and tires. (Refer to Wheel and Tire - "Wheel")
- Deflate the tires.
- Remove the tire from the wheel using the tire replacing equipment.
- Make sure the bead breaker is sufficiently separated from the TPMS sensor.
- Remove the bead at away 90º, 180º, and 270º from the valve.
- Remove the tire by levering it and rotating the wheel clockwise.
- Set the TPMS sensor at 12 o'clock from the head of the tire changer.
- When lifting the bead with the lever, make sure that the sensor is not impacted.
Tire Installation
Installation
- Lubricate the tire bead side using tire mounting lubricant.
Lubricant : Soapy water or YH 100 (Tire Lubricants)
- Place the TPMS sensor at 5 o'clock position from the tire replacing machine head for installing the bottom bead.
- Rotate the rim clockwise, and push down on the tire at the 3 o’clock position to install the bottom bead.
Install the tire on the wheel so that the bead touches the rim edge (6 o'clock direction) behind the sensor. - Push down the tire at 3 o'clock position and then rotate the rim clockwise to install the upper bead.
- Inflate the tire until the beads fit. Tire Pressure
Tire Front Rear 235/55 R19 250 - 255 kPa (36 - 37 psi) 255/45 R20 - Install the wheels and tires. (Refer to Wheel and Tire - "Wheel")
Tire Replacement
Tire Rotation
| Changing directional or asymmetric tires left/right and diagonally may result in poor driving and braking performance. |
- Rotate the front right and front left tires, and perform a road test in order to confirm vehicle stability.
- If the steering pulls to the opposite side, rotate the front and rear tires, and perform a road test again.
- If the steering continues to pull to one side, rotate the front right and left tires again, and perform a road test.
- If the steering continues to pull to the opposite side, replace the front wheels with new ones.
Wheel Removal and Installation
Removal
- Remove the wheel and tire (A) after removing the nuts.
Tightening torque : 107.9 - 128 N·m
[Front] [Rear]Be careful not to damage the hub bolts (A) when removing the wheel and tires. [Front] [Rear]
Installation
- Install the wheel and tire (A) after tightening the nuts.
Tightening torque : 107.9 - 128 N·m
[Front] [Rear]- Be careful not to damage the hub bolts (A) when installing the wheel and tires. [Front] [Rear]
- Tighten the hub nuts as follows.
- Clean the wheel side (A) and hub side (B) rust or debris prior to installing the wheels and tires. [Front] [Rear]
Wheel Inspection. Wheel Balance Inspection
Wheel Inspection
Wheel Run-out Inspection
- Jack up the vehicle and support with a jack securely.
- Measure the wheel Run-out by using a dial indicator as illustration below.
Standard Radial direction Axial direction Run-out Aluminium Wheel 0.3 mm (0.0118 in.) 0.3 mm (0.0118 in.) - If measured value exceeds the standard value, replace the wheel.
Wheel Balance Inspection
Inspection
Wheel balance needs to be adjusted if the tires are unbalanced or after tire replacement or maintenance work has been performed.Maximum rim unbalance weight : 2.12 oz (60 g)
|
Was this page helpful?