Driveshaft and Axle

Front Driveshaft Assembly (4WD)

50steps
~300min
4/5difficulty
04080120160200117.787N·mlb·ft
Tightening torque found on this page
Done 0 of 50

Contents:

Front Driveshaft Components and Components Location

Component

1. Housing (Wheel Side)
2. Driveshaft Boot Band
3. Driveshaft Boot
4. Shaft Assembly
5. Spider Assembly
6. Snap Ring
7. Housing (Reduction Gear Side)

Front Driveshaft Removal and Installation

Special Service Tool

Tool Name / Number Illustration Description
Ball joint puller
09568 - 2J100
Used for removal of tie rod end
CV joint puller
09517 - 4E000
Used for removal of CV joint
Lower arm ball joint remover
0K545 - A9100
Used for removal of front lower arm ball joint

Removal

  • When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
  • When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
  1. Disconnect the battery negative ( - ) terminal and the service interlock connector. (Refer to Battery Control System - "Auxiliary 12 V Battery - 4WD")
  2. Remove the front wheel and tires. (Refer to Suspension System - "Wheel")
  3. Remove the stabilizer bar link (A) from the front strut assembly after removing the nut.

    Tightening torque : 98.1 - 118 N·m

    • Hold the outer hex (A) when removing or installing the nut (B).
    • Be careful not to damage the boot of the link.
    • Use a hand tool when removing or installing the stabilizer bar link nut.
  4. Separate the tie rod end ball joint from the front axle.
    1. Remove the split pin (A).
    2. Remove the lock nut (B), and washer (C).

      Tightening torque : 98.1 - 118 N·m

      • Do not reuse the split pin.
      • Do not reuse the lock nut.
      • Be careful not to damage the boot of the link.
      • Use a hand tool when removing or installing the lock nut.
    3. Separate the tie rod end ball joint (A) using SST (09568 - 2J100).
  5. Separate the lower arm ball joint from the front axle using SST (0K545 - A9100).
    1. Remove the split pin (D).
    2. Remove the lower arm bolt (A), washer (B), and nut (C).

      Tightening torque : 98.1 - 118 N·m

      Fix the lower arm ball joint bolt and remove or install the nut.
      • Do not reuse the split pin.
      • Be careful not to change the position of the bolt, nut, and washer when installing.
    3. Place the support bolts (A) to the lower arm ball joint mounting hole, and then rotate them to install the SST.
      Use the support body (A) of the SST (0K545 - A9100).
    4. Install the support body (B) in the front axle groove (A).
    5. Rotate the bolt (A) to insert the support body (B) to release the front knuckle.
    6. Install the main body (A) between the front strut assembly and front lower arm.
      Use the main body (A) of the SST (0K545 - A9100).
    7. Secure the main body with the wire (A) to prevent it from falling.
    8. Install the c-clamp (A) by rotating the handle (B) to prevent the main body from slipping.
      Use the C-clamp (A) of the SST (0K545 - A9100).
    9. Tighten the bolt (A) to widen the gap of the main body so that the front lower arm can be removed from the front knuckle.
  6. Unlock the driveshaft lock nut caulking (A), by hammering on a chisel or suitable tool.
  7. Remove the driveshaft lock nut (A).

    Tightening torque : 294.2 - 314 N·m

  8. Separate the front driveshaft (A) from the front axle by using the SST (09517 - 4E000).
  9. Separate the front axle assembly (A) and front driveshaft (B).
    When removing the driveshaft, do not force pull or over bend the axle.
  10. Remove the front under cover. (Refer to Motor and Reduction Gear System - "Front Under Cover")
  11. Remove the driveshaft (A) using the pry bar (B).
    • Do not insert the pry bar too deep, as this may damage the oil seal.
    • Do not pull the driveshaft with excessive force. it may cause internal damage or dislocation.
    • Plug the hole of the reduction gear case with the oil seal cap to prevent contamination.
    • Support the driveshaft properly.

Installation

  • When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
  • When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
  1. Install in the reverse order of removal.
    • Do not reuse the driveshaft lock nut.
    • After tightening the driveshaft lock nut, caulk the lock nut to an appropriate depth (A) by using a chisel or suitable tool.

      Caulking Depth (A) : 1.5 mm (0.0590 in.) or more

    • Press the brake pedal to prevent the driveshaft from rotating when tightening the driveshaft lock nut.
    • The existing front driveshaft circlip (A) should be replaced with new one (do not reuse).

Joint Assembly (Wheel side) Removal

Removal

When able to replace the wheel side joint boot
  1. Remove the front driveshaft. (Refer to Front Driveshaft Assembly (4WD) - "Front Driveshaft")
  2. Remove the reduction gear side joint. (Refer to Front Driveshaft Assembly (4WD) - "Joint Assembly (Reduction Gear Side)")
  3. Remove the wheel side joint small diameter (A) and large diameter (B) boot band using a flat-head driver.
  4. Remove the wheel side joint boot (A).
    • Do not remove the wheel side joint housing (A).
    • Reinstall the wheel side joint housing (A) may cause leakage, so replace it with the shaft (B) as an assembly.
  5. Remove the front driveshaft. (Refer to Front Driveshaft Assembly (4WD) - "Front Driveshaft")
  6. Remove the reduction gear side joint. (Refer to Front Driveshaft Assembly (4WD) - "Joint Assembly (Reduction Gear Side)")
  7. Replace the wheel side joint assembly (A) and shaft (B).
When unable to replace the wheel side joint boot
The wheel side joint boot can not be replaced, so replace the wheel side joint assembly (A) and shaft (B) together as an assembly.

Joint Assembly (Wheel side) Installation

Special Service Tool

Tool Name / Number Illustration Description
Band installer
0K495 - C5000
Used for installing of ear type boot band
(Sharing handle with 0K495 - 2W000)

Installation

When able to replace the wheel side joint boot
  • When assembling, be careful not to let dust and foreign substances enter.
  • Driveshaft joints require special grease, so do not add any other type of grease.
  • When replacing the boot band, it must be a new one.
  1. Install the new boot (A) in the direction of the arrow.
  2. Apply the specified grease inside the boot.
    • Use the grease provided with the joint/boot kit.
    • Apply about 50 - 60% grease inside the boot.
    • Driveshaft joints require special grease, so do not add any other type of grease.
  3. Install the wheel side boot (A) into the housing (B).
  4. Install the large diameter boot band using SST (0K495 - C5000).

    Clearance (A) : 2.0 mm (0.0787 in.) or less.

  5. Install the small diameter boot band using SST (0K495 - C5000).

    Clearance (A) : 2.0 mm (0.0787 in.) or less.

    • When installing the boot band, align the fastened direction with the wheel side joint large diameter boot band.
    • Clean if there is any grease around the boot band after installing.
  6. Install the reduction gear side joint. (Refer to Front Driveshaft Assembly (4WD) - "Joint Assembly (Reduction Gear Side)")
  7. Install the front driveshaft. (Refer to Front Driveshaft Assembly (4WD) - "Front Driveshaft")
When unable to replace the wheel side joint boot
  • When assembling, be careful not to let dust and foreign substances enter.
  • Driveshaft joints require special grease, so do not add any other type of grease.
  • When replacing the boot band, it must be a new one.
  1. Replace the wheel side joint assembly (A) and shaft (B).
    The wheel side joint boot can not be replaced, so replace the wheel side joint assembly (A) and shaft (B) together as an assembly.
  2. Install the reduction gear side joint. (Refer to Front Driveshaft Assembly (4WD) - "Joint Assembly (Reduction Gear Side)")
  3. Install the front driveshaft. (Refer to Front Driveshaft Assembly (4WD) - "Front Driveshaft")

Joint Assembly (Wheel side) Inspection

Inspection

  1. Check the boot for water or foreign objects.
  2. Replace any defective parts.

Joint Assembly (Reduction gear side) Removal

Special Service Tool

Tool Name / Number Illustration Description
Band installer
0K495 - 2W001
Used for installing hook type boot band (low profile)

Removal

  • Driveshaft joints require special grease, so do not add any other type of grease.
  • When replacing the boot band, it must be a new one.
  1. Remove the front driveshaft. (Refer to Front Driveshaft Assembly (4WD) - "Front Driveshaft")
  2. Remove the reduction gear side large diameter (A) and small diameter (B) boot bands.
    Use the right tool for each type of boot band as shown in the table below.
    Ear type Hook type Hook type
    [Low profile]
    Flat-head screwdriver Flat-head screwdriver SST (0K495 - 2W001)

    When using the low profile hook type boot band, fit the SST tip (B) into the boot band hole (A) as shown below.
  3. Remove the reduction gear side joint housing (A).
  4. Remove the snap ring (A) using a snap ring pliers.
  5. Remove the spider assembly (B) from the driveshaft using a puller (A).
    Be careful not to load the roller bearings when removing the spider assembly using a puller.
  6. Remove reduction gear side boot (A).
  7. Clean the inside of the spider assembly and joint housing.
    Remove grease inside the housing as much as possible.

Joint Assembly (Reduction gear side) Installation

Special Service Tool

Tool Name / Number Illustration Description
Band installer
0K495 - C5000
Used for installing of ear type boot band
(Sharing handle with 0K495 - 2W000)
Band installer
0K495 - 2W001
Used for installing hook type boot band (low profile)
Band installer
09495 - 39100
Used for installing hook type boot band

Installation

  • When assembling, be careful not to let dust and foreign substances enter.
  • Driveshaft joints require special grease, so do not add any other type of grease.
  • When replacing the boot band, it must be a new one.
  1. Install the reduction gear side boot (A) and boot band (B) on the driveshaft.
    Put the boot band (B) first on the driveshaft before installing the boot (A).
  2. Install the spider assembly (A) on the shaft (B), then press it using a rubber mallet.
    • When installing the spider assembly (A), install it in the correct direction.
    • Installing in the wrong direction can cause secondary quality problems.
  3. Install the snap ring (A) using the snap ring pliers.
    • When replacing the joint assembly, use the new one provided in the joint kit.
    • Do not reuse the snap ring.
    • After installing the snap ring, make sure that there are only 2 - 3 splines in position (A).
  4. Install the reduction gear side joint boot (A) in the correct position.
    • When installing boot (A), make sure the boot fits into the groove (B).
    • When installing the spider assembly, fit the assembly to the boot shape.
  5. Apply specified grease inside the joint housing (A) and boot (B).
    • Use the grease provided with the joint/boot kit.
    • Apply about 70% grease to the housing (A) and about 30% grease to the boot (B).
    • Driveshaft joints require special grease, so do not add any other type of grease.
  6. Install the reduction gear side joint housing (A).
    • When installing the housing, turn the boot to fit each other.
    • If the shape of housing and boot does not fit, there is a possibility of leakage due to the gap. Be very careful.
  7. Adjust the air inside the boot to normal as shown below.
    Normal Lack of air Too much air
  8. Install the reduction gear side joint large diameter (A) and small diameter (B) boot band.
    Use the right tool for each type of boot band as shown in the table below.
    Ear type Hook type Hook type
    [Low profile]
    SST (0K495 - C5000) SST (09495 - 39100) SST (0K495 - 2W001)

    • Install in the following order : large diameter boot band (A) → small diameter boot band (B).
    • Installing in the wrong order can cause leaks.
    • When installing the boot band, align the fastened direction with the wheel side joint boot band.
    • Clean if there is any grease around the boot band after installing.
    • When installing the ear type boot band, check the clearance (A) as shown below.

      Clearance (A) : 2.0 mm (0.0787 in.) or less.

    • When using the low profile hook type boot band, fit the SST tip (B) into the boot band hole (A) as shown below.
  9. Install the front driveshaft. (Refer to Front Driveshaft Assembly (4WD) - "Front Driveshaft")

Joint Assembly (Reduction gear side) Inspection

Inspection

  1. Check spline (A) for damage / wear / crack.
  2. Check the boot for water or foreign objects.
  3. Check joint assembly for damage / wear / crack and rust.
  4. Replace any defective parts.