Driveshaft and Axle

Rear Driveshaft & Axle Assembly

65steps
~390min
4/5difficulty
060120180240300176.5130N·mlb·ft
Tightening torque found on this page
Done 0 of 65

Contents:

Integrated Drive Axle (IDA) Troubleshooting

Troubleshooting

Be careful not to misdiagnose a vehicle with brake and tailgate noise as an IDA defect.
Symptom Suspected causes Correction
Noises while braking Bumping noises when braking
Thumping noise when braking after forward/reverse
Clicking, thumping noises when braking after shifting gear position (D↔R)
Cracking noise when braking after starting the vehicle
Abnormal brake caliper play
Corroded, scratched, damaged brake discs and pads
Brake creep groan noise
Adjust or replace
Noise from the rear of the vehicle while driving Clunking, and knocking noises when driving on uneven road
Clicking, and creaking noises while accelerating or decelerating
Improper tailgate installation Adjust or replace
IDA noise / vibration Roaring noises and abnormal vibration while driving
Juddering when starting or accelerating (vibration)
Periodic crackling noise when driving (straight/turning)
1. Loosen disc mounting screws Retighten
2. Loosen wheel bearings and knuckle/carrier bolts
Motor/reduction gear and joint assembly part circlip fastening faulty
Retighten
3. Motor / reduction gear and joint assembly part circlip fastening faulty
Joint inner shaft and inner joint assembly part circlip / snap ring fastening faulty
Retighten
4. Excessive wear, play, and damage on the joint assembly Replacement
(Replacement using repair kit)
5. Bent or damaged shaft
6. Excessive wear, play, damage, or deterioration of the flange face of the wheel bearings
Leakage Boot grease scattering or leakage Improper installation of the boot or boot band

Integrated Drive Axle (IDA) Components and Components Location

Component

1. Bearing Bracket and Shaft Assy [LH]
2. Housing (Reduction Gear Side)
3. Drive axle Boot Band
4. Drive axle Boot
5. Shaft Assembly
6. Snap Ring
7. Housing and Hub Bearing (Wheel Side)

Integrated Drive Axle (IDA) Removal and Installation

Removal

  • When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
  • When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
  1. Disconnect the battery negative ( - ) terminal and the service interlock connector. (Refer to Battery Control System - "Auxiliary 12 V Battery - 2WD") (Refer to Battery Control System - "Auxiliary 12 V Battery - 4WD")
  2. Remove the rear wheel and tires. (Refer to Suspension System - "Wheel")
  3. Remove the rear under cover. (Refer to Rear Motor and Reduction Gear System - "Rear Under Cover")
  4. Remove the rear brake disc. (Refer to Brake System - "Rear Brake Disc")
  5. Separate the rear upper arm - front (A) after removing the bolt and nut.

    Tightening torque : 156.9 - 176 N·m

    • Install the transmission jack and lift up the parts to prevent the bolts and nuts from damage when installing or removing.
    • Be careful not to change the position of the bolt, nut, and washer when installing.
    Fix the bolt and remove or install the nut.
  6. Remove the Integrated Drive Axle (IDA) bolts (A).

    Tightening torque : 127.5 - 147 N·m

  7. Remove the IDA.
    • Do not pull the wheel side axle when removing IDA, damage to the inside of the reduction gear may occur, pull the joint cup (A).
    • When carrying IDA, hold the shaft or both side joints.
    • Do not insert the pry bar too deep, as this may damage the oil seal.
    • Removing the driveshaft using excessive force may damage the boot or bearing.
    • Plug the hole of the reduction gear case with the oil seal cap to prevent contamination.
    • Replace the retainer ring each time the drive shaft is removed.
    [LH]
    1. Remove the bearing bracket bolts (A).

      Tightening torque : 63.7 - 71 N·m

    2. Remove the LH IDA (A).
    [RH]
    1. Remove the RH IDA (A).
  8. Remove the bearing bracket and shaft assembly (A). [LH]

Installation

  • When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
  • When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
  1. Install in the reverse order of removal.
    The existing inner shaft circlip should be replaced with new one (do not reuse).

Integrated Drive Axle (IDA) Inspection

Inspection

  1. Check brake disc for damage.
  2. Check the rear carrier for cracks.
  3. Check hub bearing for defects.

Joint Assembly (Wheel side) Removal

Removal

  • Integrated Drive Axle (IDA) requires special grease, so do not add any other type of grease.
  • When replacing the boot band, it must be a new one.
  1. Remove the IDA. (Refer to Rear Driveshaf & Axle Assembly - "Integrated Drive Axle (IDA)")
  2. Remove the wheel side large diameter boot band (A) using a flat-head screw driver.
    Broaden the (A) using a flat-head screw driver and push the (B) to remove it.
  3. Remove the wheel side small diameter boot band (A) using a flat-head screw driver.
  4. Remove the boot (A) from the hub bearing.
  5. Extend the snap ring (A) from side to side using a snap ring plier.
    Clean the grease inside the hub bearing as much as possible using a clean cloth to locate the snap ring.
  6. Remove the hub bearing (A) while the snap ring is extended.
  7. Remove the wheel side joint boot (A).

Joint Assembly (Wheel side) Installation

Special Service Tool

Tool Name / Number Illustration Description
Band installer
0K495 - C5000
Used for installing ear type boot band(Sharing handle with 0K495 - 2W000)

Installation

  • When assembling, be careful not to let dust and foreign substances enter.
  • Integrated Drive Axle (IDA) requires special grease, so do not add any other type of grease.
  • Do not reuse the boot band.
  1. Install the boot (A), large diameter band (B), small diameter boot band (C).
    Install the boot (A) last.
  2. Apply grease inside the hub bearing (A) and boot (B).
    • Use the only grease included in the joint kit/boot kit.
    • Use only half of the grease (150g) provided.
    • Apply grease about 80% inside the bearing and about 20% inside the boot when replacing the whole part.
    • Apply grease about 20% inside the boot when replacing the boot.
    • Apply grease about 30% inside the bearing and 20% inside the boot If there is not enough grease inside the bearing.
    • Integrated Drive Axle (IDA) requires special grease, so do not add any other type of grease.
  3. Install the hub bearing (A).
    • When installing the hub bearing, make sure the spline (A) fits into the hub bearing correctly.
    • Make sure that the snap ring fits into the groove (B) securely.
    • Do not reuse the snap ring.
    • After installation, move by hand to check that the hub bearing is securely installed.
  4. Install the boot (A) to the hub bearing.
    Make sure the grooves (A), and (B) fit when installing.
  5. Install the wheel side large diameter boot band.
    1. Pre-Install the large diameter band (A).
    2. Using a tool such as a plier, tighten large diameter band (A) to install it.
    • Install in order of large diameter band → small diameter band to prevent leakage.
    • Make sure that the teeth (A) covered and the retainer cup (B) exposed after installing. If the teeth are exposed and the retainer cup is not exposed after installing, the boot band may be dislodged and grease may leak. Reinstall the boot band.
  6. Install the wheel side small diameter boot band (A) using the SST (0K495 - C5000).
    • Install in order of large diameter band → small diameter band to prevent leakage.
    • Check the gap (A) after installing.

      Ear type boot band gap (A) : 2.0 mm (0.0787 in.) or less

  7. Install the Integrated Drive Axle (IDA). (Refer to Rear Driveshaf & Axle Assembly - "Integrated Drive Axle (IDA)")

Joint Assembly (Wheel side) Inspection

Inspection

  1. Check spline (A) for damage, wear and tear.
  2. Check the boot for water or foreign objects.
  3. Check joint assembly for damage, wear and tear.
  4. Check hub bearing for damage, wear and tear.

Joint Assembly (Reduction gear side) Removal

Removal

  • Integrated Drive Axle (IDA) requires special grease, so do not add any other type of grease.
  • When replacing the boot band, it must be a new one.
  1. Remove the IDA. (Refer to Rear Driveshaf & Axle Assembly - "Integrated Drive Axle (IDA)")
  2. Remove the reduction gear side large diameter boot band (A) using a flat-head screw driver.
    Broaden the (A) using a flat-head screw driver and push the (B) to remove it.
  3. Remove the reduction gear side small diameter boot band (A) using a flat-head screw driver.
  4. Remove the boot (A) from the reduction gear side housing.
  5. Extend the snap ring (A) from side to side using a snap ring plier.
    Clean the grease inside the hub bearing as much as possible using a clean cloth to locate the snap ring.
  6. Remove the reduction gear side housing (A) while the snap ring is extended.
    Do not reuse the snap ring.
  7. Remove reduction gear side boot (A).

Joint Assembly (Reduction gear side) Installation

Special Service Tool

Tool Name / Number Illustration Description
Band installer
0K495 - C5000
Used for installing ear type boot band(Sharing handle with 0K495 - 2W000)

Installation

  • When assembling, be careful not to let dust and foreign substances enter.
  • Integrated Drive Axle (IDA) requires special grease, so do not add any other type of grease.
  • Do not reuse the boot band.
  1. Install the boot (A), large diameter band (B), small diameter boot band (C).
    Install the boot (A) last.
  2. Apply grease inside the housing (A) and boot (B).
    • Use the only grease included in the joint kit/boot kit.
    • Use only half of the grease (150g) provided.
    • Apply grease about 80% inside the housing and about 20% inside the boot when replacing the whole part.
    • Apply grease about 20% inside the boot when replacing the boot.
    • Apply grease about 30% inside the housing and 20% inside the boot If there is not enough grease inside the housing.
    • Integrated Drive Axle (IDA) requires special grease, so do not add any other type of grease.
  3. Install the reduction gear side housing (A).
    • When installing the hub bearing, make sure the spline (A) fits into the hub bearing correctly.
    • Make sure that the snap ring fits into the groove (B) securely.
    • Do not reuse the snap ring.
    • After installation, move by hand to check that the reduction gear side housing is securely installed.
  4. Install the boot (A) to the reduction gear side housing.
    Make sure the grooves (A), and (B) fit when installing.
  5. Install the reduction gear side large diameter boot band.
    1. Pre-Install the large diameter band (A).
    2. Using a tool such as a plier, tighten the (A) of the large diameter band to install it.
    • Install in order of large diameter band → small diameter band to prevent leakage.
    • Make sure that the teeth (A) covered and the retainer cup (B) exposed after installing. If the teeth are exposed and the retainer cup is not exposed after installing, the boot band may be dislodged and grease may leak. Reinstall the boot band.
  6. Install the wheel side small diameter boot band (A) using the SST (0K495 - C5000).
    • Install in order of large diameter band → small diameter band to prevent leakage.
    • Check the gap (A) after installing.

      Ear type boot band gap (A) : 2.0 mm (0.0787 in.) or less

  7. Install the Integrated Drive Axle (IDA). (Refer to Rear Driveshaf & Axle Assembly - "Integrated Drive Axle (IDA)")

Joint Assembly (Reduction gear side) Inspection. Rear axle - carrier Components and Components Location

Joint Assembly (Reduction gear side) Inspection

Inspection

  1. Check spline (A) for damage, wear and tear.
  2. Check the boot for water or foreign objects.
  3. Check joint assembly for damage, wear and tear.
  4. Check hub bearing for damage, wear and tear.

Rear axle - carrier Components and Components Location

Component

1. Rear Brake Disc
1-a. 4.9 - 5,9 N·m
2. Integrated Drive Axle (IDA)
2-a. 127.5 - 147 N·m
3. Rear Dust Cover
4. Rear Carrier
4-a. 156.9 - 176 N·m
4-b. 156.9 - 176 N·m
4-c. 98.1 - 118 N·m
4-d. 117.7 - 137 N·m
4-e. 176.5 - 196 N·m
4-f. 117.7 - 137 N·m

Rear axle - carrier Removal and Installation

Removal

  • When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
  • When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
  1. Disconnect the battery negative ( - ) terminal and the service interlock connector. (Refer to Battery Control System - "Auxiliary 12 V Battery - 2WD") (Refer to Battery Control System - "Auxiliary 12 V Battery - 4WD")
  2. Remove the rear wheel and tires. (Refer to Suspension System - "Wheel")
  3. Remove the rear under cover. (Refer to Rear Motor and Reduction Gear System - "Rear Under Cover")
  4. Remove the rear brake disc. (Refer to Brake System - "Rear Brake Disc")
  5. Remove the rear wheel speed sensor (A) after removing the bolt.

    Tightening torque : 8.8 - 13,7 N·m

  6. Separate the stabilizer bar link (A) after removing the nut.

    Tightening torque : 98.1 - 118 N·m

    Install the transmission jack and lift up the parts to prevent the bolts and nuts from damage when installing or removing.
  7. Separate the rear assist arm (A) after removing the the bolt, nut, and washer.

    Tightening torque : 117.7 - 137 N·m

    • Install the transmission jack and lift up the parts to prevent the bolts and nuts from damage when installing or removing.
    • Be careful not to change the position of the bolt, nut, and washer when installing.
    Fix the bolt and remove or install the nut.
  8. Separate the trailing arm (A) after removing the bolt and nut.

    Tightening torque : 117.7 - 137 N·m

    • Install the transmission jack and lift up the parts to prevent the bolts and nuts from damage when installing or removing.
    • Be careful not to change the position of the bolt, nut, and washer when installing.
    Fix the bolt and remove or install the nut.
  9. Separate the rear upper arm - front (A) after removing the bolt and nut.

    Tightening torque : 156.9 - 176 N·m

    • Install the transmission jack and lift up the parts to prevent the bolts and nuts from damage when installing or removing.
    • Be careful not to change the position of the bolt, nut, and washer when installing.
    Fix the bolt and remove or install the nut.
  10. Separate the rear upper arm - rear (A) after removing the bolt, nut, and washer.

    Tightening torque : 156.9 - 176 N·m

    • Install the transmission jack and lift up the parts to prevent the bolts and nuts from damage when installing or removing.
    • Be careful not to change the position of the bolt, nut, and washer when installing.
    Fix the bolt and remove or install the nut.
  11. Separate the rear lower arm (A) after removing the bolt, nut, and washer.

    Tightening torque : 176.5 - 196 N·m

    • Install the transmission jack and lift up the parts to prevent the bolts and nuts from damage when installing or removing.
    • Be careful not to change the position of the bolt, nut, and washer when installing.
    Fix the bolt and remove or install the nut.
  12. Remove the inner shaft bearing bracket bolts (A). [LH]

    Tightening torque : 63.7 - 71 N·m

  13. Remove the rear carrier and Integrated Drive Axle (IDA) (A).
    • Do not pull the wheel side axle when removing IDA, damage to the inside of the reduction gear may occur, pull the joint cup (A).
    • When carrying IDA, hold the shaft or both side joints.
    • Do not insert the pry bar too deep, as this may damage the oil seal.
    • Removing the driveshaft using excessive force may damage the boot or bearing.
    • Plug the hole of the reduction gear case with the oil seal cap to prevent contamination.
    • Replace the retainer ring each time the drive shaft is removed.
  14. Remove the rear stabilizer bar link (A) after removing the nut.

    Tightening torque : 98.1 - 118 N·m

  15. Remove the IDA mounting bolts (A).

    Tightening torque : 127.5 - 147 N·m

  16. Remove the IDA and rear dust cover (A).

Installation

  • When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
  • When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
  1. Install in the reverse order of removal.
  2. Check the alignment. (Refer to Suspension System - "Alignment")

Rear axle - carrier Inspection

Inspection

  1. Check the rear carrier for cracks.