Suspension System

Description and Operation

20steps
~120min
4/5difficulty
02040608010053.940N·mlb·ft
Tightening torque found on this page
Done 0 of 20

Contents:

Description and Operation

Description

  • Wheel alignment is all forces due to friction, gravity, centrifugal force and inertia operate in a balanced manner while driving.
  • Wheel alignment improves linearity, grounding performance, tire life extension and fuel reduction and ensures safety at high speeds.
  • Alignment adjustments consist of camber, castor, kingpin angle, toe, left, thrust angle, etc.

Components

Camber Camber refers to the angle at which the top of the wheel is tilted inward or outward relative to the vertical line started from the center of the floor when the vehicle is viewed from the front.
  • It facilitates steering control of the steering wheel and prevents bending of the front axle.
( + ) Camber It is a camber form with wheels tilted outward from the top. It prevents the underside of the wheel from opening, so there is less tire wear due to unnecessary driving resistance on curves.
Suspension System — Alignment / Description and Operation / Components illustration
( - ) Camber It is a camber form with wheels tilted inward from the top. cause strong friction when driving curves but tires are prone to wear.
Suspension System — Alignment / Description and Operation / Components illustration
Caster Caster refers to the angle at which the steering shaft tilts forward and backward relative to the vertical line initiated from the center of the wheel floor when the vehicle is viewed from the side.
  • It gives a straight line to the steering wheel when driving.
  • Provides resilience to wheels when steering.
  • It prevents shaking of wheels while driving.
Suspension System — Alignment / Description and Operation / Components illustration
King pin angle Kingpin angle refers to the angle at which the centerline of the steering shaft and the bottom vertical line forms when the vehicle is viewed from the front.
  • Provides easy steering of the steering wheel and resilience of the steering wheel.
  • The kingpin angle and camber are also called Included Angle (I.A.). [Included Angle (I.A.)]
Suspension System — Alignment / Description and Operation / Components illustration
Item Description
A Strut centerline
B King pin angle
C Centerline

Toe Toe is the tilted angle or distance at the front of the wheel when looking up and down at the vehicle.
  • The state in which the front of the wheel faces outward is called Toe out, and the state in which the front of the wheel faces inward is called Toe in.
  • In general vehicles, toe-in is applied to prevent side slip. ※ Side slip: A phenomenon in which the wheels slide sideways due to the influence of the camber while the vehicle is driving.
  • Toe-out is sometimes applied to vehicles that require a fast steering response when turning.
Suspension System — Alignment / Description and Operation / Components illustration
Set Back Set back refers to the angle at which the line connects the center of the front wheels from the vehicle's centerline.
  • The main cause of the set back is the presence of an accident in the vehicle or an abnormality in the body.
Suspension System — Alignment / Description and Operation / Components illustration
Thrust angle The angle at which the Thrust line and the centerline of the vehicle are formed. ※Thrust line: A line that is perpendicular to the center line of the vehicle and the center line of the rear axle.
  • Thrust conditions occur when the rear wheel individual toe is not the same.
Suspension System — Alignment / Description and Operation / Components illustration
Information
Poor thrust angles can increase tire wear, reduce steering direction, and cause dog tracking. ※Dog tracking: The driving condition when the thrust line is not parallel to the center line of the vehicle
Suspension System — Alignment / Description and Operation / Components illustration

On Vehicle Inspection

On Vehicle Inspection

Driving Test Carry out pre-work vehicle driving tests to check vehicle behavior under normal driving conditions.

On straight, flat road

  1. Check that the vehicle is going straight when release the steering wheel.

Stop and Go

  1. Check that the vehicle pulls to one side while accelerating and braking.

Turning left or right

  1. Check whether the vehicle is restored to a straight line when released the steering wheel after turning.
Tire Wear Inspection
Wheel and tire diagnosis
Rapid wear at the center Rapid wear at both shoulders Wear at one shoulder
Suspension System — Alignment / On Vehicle Inspection illustration
Suspension System — Alignment / On Vehicle Inspection illustration
Suspension System — Alignment / On Vehicle Inspection illustration
  • Center-tread down to fabric due to excessively over inflated tires
  • Lack of rotation
  • Excessive toe on drive wheels
  • Heavy acceleration on drive
  • Under-inflated tires
  • Worn suspension components
  • Excessive cornering speeds
  • Lack of rotation
  • Toe adjustment out of specification
  • Camber out of specification
  • Damaged strut
  • Damaged lower arm
Partial wear Feathered edge Wear pattern
Suspension System — Alignment / On Vehicle Inspection illustration
Suspension System — Alignment / On Vehicle Inspection illustration
Suspension System — Alignment / On Vehicle Inspection illustration
  • Damaged or worn brake discs
  • Sudden excessive braking
  • Toe adjustment out of specification
  • Damaged or worn tie rods
  • Damaged knuckle
  • Toe adjustment out of specification
  • Lack of rotation
  • Damaged suspension component

Inspect steering system related parts
  1. Check the steering gear box for damage or installed firmly.
  2. Check the tie rod end ball joint for damage or free play.
  3. Check each suspension bushing for wear, cracks, etc.
  4. Check the strut and shock absorber for damage.
  5. Check the ride height
  6. Check the coil spring for damage or wear.
  7. Check the lower arm ball joint for damage or free play.
Inspect suspension system related parts

Repair procedures

Wheel Alignment Repair Procedures

  1. When using the wheel alignment tester to check the wheel alignment, align the lift's vehicles horizontally.
  2. Set the transmission gear to 'N'.
  3. Inflate the 4 tires to the specified tire pressure. Tire Pressure
    Item Size Specification
    Front Rear
    Tire Pressure 205/60 R16 230 kPa (33 psi) 230 kPa (33 psi)
    215/55 R17 240 kPa (35 psi) 230 kPa (33 psi)
    235/45 R18 230 kPa (33 psi) 230 kPa (33 psi)
  4. Align the steering wheel in a straight-ahead position using a digital level or other equivalent tools.

    Allowable steering wheel alignment range : 0.0 ± 0.5°

    Suspension System — Alignment / Repair procedures / Wheel Alignment Repair Procedures illustration
  5. Hold the brake pedal depressed using a pedal stopper.
  6. Measure the ride height, which is the distance from the end of the fender to the center of the wheel.
    Ride height Front (A) : 2WD : 405 ± 10 mm (15.94 ± 0.40 in.) 4WD : 412 ± 10 mm (16.20 ± 0.40 in.) Rear (B) : 411 ± 10 mm (16.18 ± 0.40 in.)
    Suspension System — Alignment / Repair procedures / Wheel Alignment Repair Procedures illustration
  7. Adjust the alignment. (Refer to Alignment - "Adjust")
    Note
    It is not recommended to adjust the rear alignment of the coupled torsion beam axle using an adjustment shim or washer. Vehicle performance may be poor.
  8. Shake the vehicle up and down after alignment adjustment.
    Note
    If the figure changes significantly, check the suspension for cracks, tears, wear, and damage to the bushing.
  9. After adjustment, perform the Steering Angle Sensor (SAS) Calibration using KDS. (Refer to Steering System - "Steering Angle Sensor (SAS) Calibration")

Adjustment

Adjustment

[Rear - Multi Link]
Note
It is not recommended to adjust the rear alignment of the coupled torsion beam axle type using an adjustment shim or washer. Vehicle performance may be poor.

Toe

Turn the cam bolt (A) attached with the rear assist arm clockwise or counterclockwise to adjust the toe. Adjust the left and right cam bolts to the same amount.

Total : 0.01° ± 0.2° Individual : 0.005° ± 0.1°

Cam bolt Rotation Increae / Decrease
RH Clockwise Toe-In
LH Clockwise Toe-Out

Suspension System — Alignment / Adjustment illustration
Information
Adjust the toe using total toe.

Camber

Turn the cam bolts (A) attached with the rear lower arm clockwise or counterclockwise to adjust the camber.

Camber Angle : -1.2 ± 0.5°

Cam bolt Rotation Increae / Decrease
RH Clockwise + Camber
LH Clockwise - Camber

Suspension System — Alignment / Adjustment illustration

Thrust angle

Thrust angle : 0° ± 0.15°

Suspension System — Alignment / Adjustment illustration
[Front]

Toe

Toe is adjusted by rotation of the tie rod rotation buckle. Turning the tie rod to the rear of the vehicle will reduce the toe on the front wheels. The adjustment toe is adjusted by turning the left and right tie rods to the same value.

Total : 0.12° ± 0.2° Individual : 0.06° ± 0.1°

Suspension System — Alignment / Adjustment illustration
  1. Loosen the tie rod end nut (A) until the toe can be adjusted.

    Tierod tightening torque : 49.0 - 54 N·m

    Suspension System — Alignment / Adjustment illustration
  2. Fix the tie rod end (A) with a wrench to prevent turning during adjustment.
    Suspension System — Alignment / Adjustment illustration
  3. Rotate the tie rod turn buckle (A) to adjust the toe to the specified value.
    Suspension System — Alignment / Adjustment illustration
    Note
    After toe adjustment, match the remaining number of threads on the left and right equally.
  4. After adjustment, tighten the tie rod end nut (A) to specification torque.

    Tierod tightening torque : 49.0 - 54 N·m

    Suspension System — Alignment / Adjustment illustration
Note
  • Be careful not to twist the bellows boot when adjusting the toe.
  • After toe adjustment, adjust the tie rod end position horizontally to ensure that the ball joint boot (A) is not pressed.
    Suspension System — Alignment / Adjustment illustration

Camber

The camber cannot be adjusted. If the measured camber exceeds the standard limit, repair or replace the relevant parts and inspect the wheel alignment again.

Camber angle : 2WD : -0.5° ± 0.5° 4WD : -0.4° ± 0.5°

Suspension System — Alignment / Adjustment illustration
Item Description
A Camber Angle
B Center line

Caster

The caster cannot be adjusted. If the measured caster exceeds the standard limit, repair or replace the relevant parts and inspect the wheel alignment again.
Tire Size Drive Type Specification
205/60 R16 2WD 4.33 ± 0.5
4WD 4.28 ± 0.5
215/55 R17 2WD 4.34 ± 0.5
4WD 4.29 ± 0.5
235/45 R18 2WD 4.37 ± 0.5
4WD 4.31 ± 0.5

Suspension System — Alignment / Adjustment illustration
Information
  • Before measuring the front wheel alignment, wear, loose and damaged parts of the front suspension assembly should be replaced.
  • Camber and caster are assembled at the specified value during production and need not be adjusted.
  • If the camber and caster are not within the specified limits, replace the bent or damaged parts.
  • The difference between the left and right wheels of Camber and Caster shall be within 0° ± 0.5°.

Kingpin

The king pin angle cannot be adjusted. If the measured caster exceeds the standard limit, repair or replace the relevant parts and inspect the wheel alignment again.

King ping angle : 2WD : 13.8° ± 0.5° 4WD : 13.6° ± 0.5°

Suspension System — Alignment / Adjustment illustration
Item Description
A Strut center line
B Kingpin
C Center line

Set back

The set back cannot be adjusted, but their values are useful for diagnosing steering problems, such as pull and wander. After repairing a vehicle with a damaged frame, the set back must be checked. The ideal set back value should be 0.
Suspension System — Alignment / Adjustment illustration