Suspension System

Wheel and Tire

22steps
~132min
4/5difficulty
04080120160200127.594N·mlb·ft
Tightening torque found on this page
Done 0 of 22

Contents:

Tire Inspection

Tire Wear

  1. Measure the tread depth of the tires.
    Tread depth [Limit] : Normal condition : 1.6 mm (0.06 in.) At high speed condition : 2.4 mm (0.09 in.)
  2. If the remaining tread depth (A) is less than the limit, replace the tire.
    Suspension System — Wheel and Tire / Tire / Inspection / Tire Wear illustration
    Note
    Tire replacement is recommended when the wear limit indication (B) and the tread depth (A) are recommended.

Tire Removal

Removal

  1. Remove the wheels and tires. (Refer to Tires/Wheels - "Wheel")
  2. Deflate the tires.
  3. Remove the tire from the wheel using the tire replacing equipment.
    Suspension System — Wheel and Tire / Tire / Removal illustration
    Note
    • Make sure the bead breaker is sufficiently separated from the TPMS sensor.
    • Remove the bead at away 90º, 180º, and 270º from the valve.
  4. Remove the tire by levering it and rotating the wheel clockwise.
    Suspension System — Wheel and Tire / Tire / Removal illustration
    Suspension System — Wheel and Tire / Tire / Removal illustration
    Note
    • Set the TPMS sensor at 12 o'clock from the head of the tire changer.
    • When lifting the bead with the lever, make sure that the sensor is not impacted.

Tire Installation

Installation

  1. Lubricate the tire bead side using tire mounting lubricant.

    Specified Lubricant : Soapy water or YH100 (Lubricants for tire assembling)

    Suspension System — Wheel and Tire / Tire / Installation illustration
  2. Place the TPMS sensor at 5 o'clock position from the tire replacing machine head for installing the bottom bead.
    Suspension System — Wheel and Tire / Tire / Installation illustration
  3. Rotate the rim clockwise, and push down on the tire at the 3 o’clock position to install the bottom bead.
    Suspension System — Wheel and Tire / Tire / Installation illustration
    Note
    Install the tire on the wheel so that the bead touches the rim edge (6 o'clock direction) behind the sensor.
  4. Push down the tire at 3 o'clock position and then rotate the rim clockwise to install the upper bead.
    Suspension System — Wheel and Tire / Tire / Installation illustration
  5. Inflate the tire until the beads fit.
    Suspension System — Wheel and Tire / Tire / Installation illustration
    Tire Pressure
    Size Specification
    Front Rear
    205/60 R16 230 kPa (33 psi) 230 kPa (33 psi)
    215/55 R17 240 kPa (35 psi) 230 kPa (33 psi)
    235/45 R18 230 kPa (33 psi) 230 kPa (33 psi)
  6. Install the wheels and tires. (Refer to Tires/Wheels - "Wheel")

Tire Replacement

Tire Rotation

Note
When directional or asymmetric tires applied, do not perform left/right or diagonal tire replacement. Driving and braking performance may be poor which may affect safety.
Replace the tire in the direction shown by the arrow in the figure below.
Suspension System — Wheel and Tire / Tire / Replacement / Tire Rotation illustration
Pre-inspection when the vehicle is pulling to one side
  1. Inspect the tire pressure. Tire pressure
    Size Specification
    Front Rear
    205/60 R16 230 kPa (33 psi) 230 kPa (33 psi)
    215/55 R17 240 kPa (35 psi) 230 kPa (33 psi)
    235/45 R18 230 kPa (33 psi) 230 kPa (33 psi)
  2. Check the steering wheel off-center.
  3. Check the wheel alignment. (Refer to Alignment - "Repair Procedures")
  4. Rotate the front right and front left tires, and perform a road test in order to confirm vehicle stability.
    Suspension System — Wheel and Tire / Tire / Replacement / Tire Rotation illustration
  5. If the steering pulls to the opposite side, rotate the front and rear tires, and perform a road test again.
    Suspension System — Wheel and Tire / Tire / Replacement / Tire Rotation illustration
  6. If the steering continues to pull to one side, rotate the front right and left tires again, and perform a road test.
    Suspension System — Wheel and Tire / Tire / Replacement / Tire Rotation illustration
  7. If the steering continues to pull to the opposite side, replace the front wheels with new ones.
    Suspension System — Wheel and Tire / Tire / Replacement / Tire Rotation illustration
Rotating For Pull And Wander If there is no abnormality in the vehicle after a pre-inspection and the vehicle continues to pull to one side, uneven tire wear may be the cause. In this case, the following tire replacement procedures shall be performed.

Wheel Removal and Installation

Removal

  1. Remove the wheel and tire (A).

    Tightening torque : 107.9 - 128 N·m

    [Front]
    Suspension System — Wheel and Tire / Wheel / Removal and Installation / Removal illustration
    [Rear]
    Suspension System — Wheel and Tire / Wheel / Removal and Installation / Removal illustration
    Note
    Be careful not to damage the hub bolts (A) when removing the wheel and tires. [Front]
    Suspension System — Wheel and Tire / Wheel / Removal and Installation / Removal illustration
    [Rear]
    Suspension System — Wheel and Tire / Wheel / Removal and Installation / Removal illustration

Installation

  1. Install the wheel and tire (A).

    Tightening torque : 107.9 - 128 N·m

    [Front]
    Suspension System — Wheel and Tire / Wheel / Removal and Installation / Installation illustration
    [Rear]
    Suspension System — Wheel and Tire / Wheel / Removal and Installation / Installation illustration
    Note
    • Be careful not to damage the hub bolts (A) when installing the wheel and tires. [Front]
      Suspension System — Wheel and Tire / Wheel / Removal and Installation / Installation illustration
      [Rear]
      Suspension System — Wheel and Tire / Wheel / Removal and Installation / Installation illustration
    • Tighten the hub nuts as follows.
      Suspension System — Wheel and Tire / Wheel / Removal and Installation / Installation illustration
    • Remove rust or debris from the contact surface of the wheel side (A) and the hub side (B) and install the wheels and tires.
      Suspension System — Wheel and Tire / Wheel / Removal and Installation / Installation illustration
      [Front]
      Suspension System — Wheel and Tire / Wheel / Removal and Installation / Installation illustration
      [Rear]
      Suspension System — Wheel and Tire / Wheel / Removal and Installation / Installation illustration

Wheel Inspection

Wheel Run-out Inspection

  1. Jack up the vehicle and support with a jack securely.
  2. Measure the wheel Run-out by using a dial indicator as illustration below.
    Limit Circumferential Axial
    Run-out Aluminium Wheel 0.3 0.3

    Suspension System — Wheel and Tire / Wheel / Inspection / Wheel Run-out Inspection illustration
  3. If measured value exceeds the standard value, replace the wheel.

Wheel Balance Description and Operation

Description

Symptoms of Defective Wheel Balance
If the wheel balance is defective 1. Steering wheel vibration occurs.
2. Road impact is transmitted to the steering wheel during driving.
3. Irregular tire wear occurs.
4. Driving vibration decreases ride comfort.

Types of Wheel Imbalance
Symptoms of Defective Static Balance(If the tire weight is applied to only one side) Symptoms of Defective Dynamic Balance(If the tire weight is not applied equally to left and right sides)
Suspension System — Wheel and Tire / Wheel Balance / Description and Operation / Description illustration
  • The tire bounces vertically.
  • A: Unbalanced weight
Suspension System — Wheel and Tire / Wheel Balance / Description and Operation / Description illustration
  • The tire wobbles from side to side.
  • Effect on steering and driving stability.
  • A: Unbalanced weight

Types of Wheel Balance
Road Balancing Road Force Balancing
If the imbalance symptoms occur due to defective wheel balance after road balancing, do road force balancing.
Inspection and Adjustment Procedure
  • Install the tire on the balancing equipment. Examine the tire balance.
  • When imbalance occurs, turn the tire as shown on the screen. Attach the balance weight to the wheel for adjustment.
  • Install the tire on the balance equipment. Examine the road force balance.
  • When imbalance occurs, attach the balance weight at the position marked by the red laser.
  • A: Road roller
Wheel balance equipment
Suspension System — Wheel and Tire / Wheel Balance / Description and Operation / Description illustration
Suspension System — Wheel and Tire / Wheel Balance / Description and Operation / Description illustration

  • Road Balancing
  • Tire road balancing is a procedure to examine and adjust that the weight of the tire and wheel is equally applied around the rotation axis during turning.
  • Do road balancing if tire wear is irregular, the steering wheel vibrates, or the tire is replaced.
  • If imbalance is caused by irregular weight distribution, install balance weight on the wheel to adjust the weight.
  • If road balancing does not correct the problem, do road force balancing.
  • Road Force Balancing
  • Road force balancing is a accurate procedure that applies vertical load to the tire under conditions equivalent to actual driving. It measures and adjusts imbalances caused by tire deformation and lateral wobble that cannot be identified by standard balancing.
  • Do road force balancing if tire wear is irregular, the steering wheel vibrates, or the tire is replaced.
  • If imbalance is caused by unbalanced weight distribution, install the balance weight on the wheel at the position marked by the red laser.
  • If road force balancing does not correct the problem, damage to the wheel or a tire defect can be predicted.

Wheel Balance Inspection

Inspection

Wheel balance needs to be adjusted if the tires are unbalanced or after tire replacement or maintenance work has been performed.

Maximum rim unbalance weight : 2.12 oz (60 g)

Suspension System — Wheel and Tire / Wheel Balance / Inspection illustration
Note
  • If the maximum unbalance weight over than 3.53 oz (100g), reassemble the wheel and tire, then perform the wheel balance adjustment.
  • Make sure that the wheel and tire install in the balancer securely.
  • Do not use an On-car balance it may damage the vehicle.
  • For details, refer to the instructions of each balancer.
  • Use flange type balance lead (A) or non-flange type balance lead (B) depending on wheel flange type.
    Suspension System — Wheel and Tire / Wheel Balance / Inspection illustration