Maintenance

Brake/Clutch Fluid Inspection

74steps
~444min
4/5difficulty
02040608010053.940N·mlb·ft
Tightening torque found on this page
Done 0 of 74

Contents:

Brake/Clutch Fluid Inspection

Inspection

Check the brake fluid level in the brake fluid reservoir. The level should be between “MIN” and “MAX” marks on the side of the reservoir.
Maintenance — Chassis / Brake/Clutch Fluid / Inspection illustration
Use only hydraulic brake fluid conforming to DOT 4 specification. Check the brake system for any leakage if the fluid level is extremely low (lower than MIN). (Refer to Brake System - "Inspection")

Brake Lines, Hoses and Connections Inspection

Inspection

Visually check for proper installation, chafing, cracks, deterioration and any leakage. Replace any deteriorated or damaged parts immediately.

Disc Brakes and Pads Inspection

On Vehicle Inspection

Disc Cleaning before Inspection The rust caused by leaving the vehicle unattended for a long period of time is naturally removed under normal driving conditions. It may affect thickness and runout measurements, please remove rust on the brake disc for accurate measurements.
  1. Check the brake disc for rust.
  2. Spray the cleaning solution on rusted surface of disc.

    Cleaning solution : Water (300 ml) + Detergent (15 ml)

    Warning
    Do not use lubricating, oil-based cleaning agents (wax, rust inhibitors). Poor braking performance and risk of fire due to pad friction during braking.
  3. Drive the vehicle up to 30 mph and depress the brake up to stop for complete repeat more than 5 cycles.
  4. Clean the brake disc with clean water.
  5. Check the brake disc for rust.
  6. If rust is not removed, repeat the above procedure again.
  7. Remove the front wheel and tires. (Refer to Suspension System - "Wheel")
  8. Check the brake disc for damage.
  9. Measure the brake disc thickness (A) and run-out using the micro meter and dial gauge at least 24 locations on the same column along the lines shown in the figure below.
    Maintenance — Chassis / Disc Brakes and Pads / Inspection / On Vehicle Inspection illustration

    Front Brake Disc Thicknes Standard for 15 inch wheel disc : 23.0 mm (0.90 in.) for 16 in wheel disc : 25.0 mm (0.98 in.) Service Limit for 15 inch wheel disc : 21.4 mm (0.84 in.) for 16 inch disc : 23.4 mm (0.92 in.) DTV (Disc Thickness Variation) : 0.015 mm (0.0005 in.) [Circumference, Radial direction]
  10. If the thickness difference between each measuring part is greater than standard, resurface or replace the brake disc.
    Note
    • Resurface the brake disc according to the method of using the equipment in possession.
    • If the brake disc is less than or equal to the limit, replace the brake disc with a new one.
  11. Install the front wheel and tires. (Refer to Suspension System - "Wheel")
  12. Remove the front wheel and tires. (Refer to Suspension System - "Wheel")
  13. Install the dial gauge perpendicular to the brake disc's external diameter of 10 mm (0.40 in.) and rotate the disc to measure the run-out.

    Brake Disc Run Out Service Limit : 0.050 mm (0.0019 in.)

    Maintenance — Chassis / Disc Brakes and Pads / Inspection / On Vehicle Inspection illustration
  14. If the brake disc run-out exceeds the limit, resurface or replace the brake disc.
    Note
    • Resurface the brake disc according to the method of using the equipment in possession.
    • If the brake disc is less than or equal to the limit, replace the brake disc with a new one.
  15. Install the front wheel and tires. (Refer to Suspension System - "Wheel")
  16. Remove the rear wheel and tires. (Refer to Suspension System - "Wheel")
  17. Check the brake disc for damage.
  18. Measure the brake disc thickness (A) and run out using a micrometer and dial gauge. Measure it at least 24 points.
    Rear brake disc thickness (A) Standard : 10.0 mm (0.39 in.) Service limit : 8.4 mm (0.33 in.) DTV (Disc Thickness Variation : Less than 0.015 mm (0.0006 in.) [Circumference direction] Less than 0.015 mm (0.0006 in.) [Radial direction]
    Maintenance — Chassis / Disc Brakes and Pads / Inspection / On Vehicle Inspection illustration
  19. If the thickness difference between each measuring part is greater than standard, resurface or replace the brake disc.
    Note
    • Resurface the brake disc according to the method of using the equipment in possession.
    • If the brake disc is less than or equal to the limit, replace the brake disc with a new one.
  20. Install the rear wheel and tires. (Refer to Suspension System - "Wheel")
  21. Remove the rear wheel and tires. (Refer to Suspension System - "Wheel")
  22. Install the dial gauge perpendicular to the brake disc's external diameter of 10 mm (0.40 in.) and rotate the disc to measure the run-out.

    Brake Disc Run Out Service limit : 0.055 mm (0.002 in.) or less.

    Maintenance — Chassis / Disc Brakes and Pads / Inspection / On Vehicle Inspection illustration
  23. If the brake disc run-out exceeds the limit, resurface or replace the brake disc.
    Note
    • Resurface the brake disc according to the method of using the equipment in possession.
    • If the brake disc is less than or equal to the limit, replace the brake disc with a new one.
  24. Install the rear wheel and tires. (Refer to Suspension System - "Wheel")
Front Brake Disc Thickness Check Front Brake Disc Runout Inspection Rear Brake Disc Thickness Check Rear Brake Disc Runout Inspection

Brake Pad Check

  1. Check brake pad thickness (A). If the thickness is thinner than the limit, replace the brake pads.
    Front brake pad thickness Standard : for 15 inch wheel disc : 11.0 mm (0.43 in.) for 16 inch wheel disc : 11.5 mm (0.45 in.) Service Limit : 2.5 mm (0.09 in.)

    Rear brake disc pad thickness Standard : EPB : 10.0 mm (0.393 in.) None EPB : 9.0 mm (0.35 in.) Service Limit : 2.0 mm (0.078 in.)
    Maintenance — Chassis / Disc Brakes and Pads / Inspection / On Vehicle Inspection illustration
  2. Check that grease is applied to sliding contact points and check the pad and backing metal for damage.

Drive Shafts and Boots Inspection

Inspection

  1. Check the drive shaft boots for loose clamps, cracks, grease leaks, kinks or damage.
    Maintenance — Chassis / Drive Shafts and Boots / Inspection illustration

Parking Brake Inspection

Inspection

[Electric Parking Brake (EPB)]

  1. Check if the parking brake applying sound is heard when the EPB switch is operated.
  2. Make sure that the parking brake indicator 'ON' when EPB switch applied and 'OFF' after EPB switch released.

[None EPB]

Note
After disassembling/assembling the torque member or replacing the caliper, parking brake cable or brake disc, re-adjust the parking brake.
  1. To fit the cable, follow one of these procedures before adjusting.
    • Apply a parking brake fully more than 3 times
    • With full operation, hold the parking brake for 1 to 2 hours.
  2. Remove the floor console assembly. (Refer to Body - "Floor Console Assembly")
  3. After fitting the cable, adjust the parking brake cable so that the stroke is 5 - 6 notch when operating the pedal with 30kgf at point (A).
    Maintenance — Chassis / Parking Brake / Inspection illustration
    Note
    • For the BIR type, adjust the adjustment nut of the lever assembly so that the sum of the O / P lever (A) and the stopper (B) (LH / RH) angle is within 3.0 mm (0.11 in).
      Maintenance — Chassis / Parking Brake / Inspection illustration
    • Adjust the parking brake cable by tightening or loosening the adjusting nut (A).
      Maintenance — Chassis / Parking Brake / Inspection illustration
  4. Make sure that there is no gap between adjustment nut and clip after adjusting the parking brake.
  5. Make sure that the brakes are not drag.
  6. Make sure that the parking brake switch is 'ON' before the parking lever is operated by 1 notch and 'OFF' when released.
  7. Check whether the wheel operates smoothly.
  8. Perform driving test.

Steering Gear Rack, Linkage and Boots Inspection

Inspection

Steering Wheel Play Inspection
  1. Align the steering wheel in a straight-ahead position using a digital level or other equivalent tools.

    Allowable steering wheel alignment range : 0.0 ± 0.5°

    Maintenance — Chassis / Steering Gear Rack, Linkage and Boots / Inspection illustration
  2. With MDPS power on, lightly turn the steering wheel from side to side to measure the distance the steering wheel rotates until the wheel moves.

    Allowable steering wheel play : 0 - 30 mm ( 0 - 1.18 in.)

    Maintenance — Chassis / Steering Gear Rack, Linkage and Boots / Inspection illustration
  3. If the steering wheel play exceeds standard value, inspect the steering column, shaft, and linkages.
  4. Align the steering wheel in a straight-ahead position using a digital level or other equivalent tools.

    Allowable steering wheel alignment range : 0.0 ± 0.5°

    Maintenance — Chassis / Steering Gear Rack, Linkage and Boots / Inspection illustration
  5. With MDPS powered on, apply a spring scale to the end of the steering wheel and pull the scale to measure the force when the steering wheel begins to move.

    Stationary steering force : Maximum 3.0 kgf (29.0 N, 6.6 lbf)

    Maintenance — Chassis / Steering Gear Rack, Linkage and Boots / Inspection illustration
  6. If the measured value exceeds standard value, inspect the steering gear box or MDPS.
  7. Mark the steering wheel upper (A) and upper cover (B) using the masking tape.
    Maintenance — Chassis / Steering Gear Rack, Linkage and Boots / Inspection illustration
  8. Align the steering wheel and mark the straight line (A) on the masking tape.
    Maintenance — Chassis / Steering Gear Rack, Linkage and Boots / Inspection illustration
  9. Keep the vehicle straight and drive about 100 m, and mark the new straight line (A) as the steering wheel is turned.
    Maintenance — Chassis / Steering Gear Rack, Linkage and Boots / Inspection illustration
  10. Remove the front wheel and tires. (Refer to Suspension System - "Wheel")
  11. Loosen the tie rod end nut (A) enough to adjust the steering wheel off center.
    Tie rod tightening torque : 49.0 - 54 N·m
    Maintenance — Chassis / Steering Gear Rack, Linkage and Boots / Inspection illustration
  12. Fix the tie rod end (A) with a spanner to prevent turning during adjustment.
    Maintenance — Chassis / Steering Gear Rack, Linkage and Boots / Inspection illustration
  13. Turn the tie rod turnbuckle (A) clockwise or counterclockwise to adjust the steering wheel off center.
    Maintenance — Chassis / Steering Gear Rack, Linkage and Boots / Inspection illustration
    [Tie rod turnbuckle rotation according to steering wheel off center]
    Maintenance — Chassis / Steering Gear Rack, Linkage and Boots / Inspection illustration
    Note
    • During adjustment, check the distance (A) from time to time, do not adjust the turnbuckle in the direction of increasing the distance (A).
      Maintenance — Chassis / Steering Gear Rack, Linkage and Boots / Inspection illustration
    • Adjust the RH and LH tie rods as below. (LH clockwise once → RH counterclockwise once)
  14. Tighten the tie rod end nut (A) after adjustment.
    Tie rod tightening torque : 49.0 - 54 N·m
    Maintenance — Chassis / Steering Gear Rack, Linkage and Boots / Inspection illustration
  15. Install the front wheel and tires. (Refer to Suspension System - "Wheel")
  16. Check the wheel alignment. (Refer to Suspension System - "Alignment")
Checking Stationary Steering Effort Steering Wheel Off Center Inspection

Suspension Ball Joints Inspection

Inspection

Visually check, must be free from injurious flaw and crack.

Suspension Mounting Bolts Inspection

Inspection

Visually check the loose mount bolt.

Tire (pressure & tread wear) Inspection

Tire Pressure

Tire Pressure
  1. Check the tire pressure.
    Size Specification
    Front Rear
    205/60 R16 230 kPa (33 psi) 230 kPa (33 psi)
    215/55 R17 240 kPa (35 psi) 230 kPa (33 psi)
    235/45 R18 230 kPa (33 psi) 230 kPa (33 psi)

Tire Rotation

Note
When directional or asymmetric tires applied, do not perform left/right or diagonal tire replacement. Driving and braking performance may be poor which may affect safety.
Replace the tire in the direction shown by the arrow in the figure below.
Maintenance — Chassis / Tire (pressure & tread wear) / Inspection / Tire Rotation illustration
Checking For Pull And Wander If the steering pulls to one side, rotate the tires according to the following wheel rotation procedure.
  1. Rotate the front right and front left tires, and perform a road test in order to confirm vehicle stability.
    Maintenance — Chassis / Tire (pressure & tread wear) / Inspection / Tire Rotation illustration
  2. If the steering pulls to the opposite side, rotate the front and rear tires, and perform a road test again.
    Maintenance — Chassis / Tire (pressure & tread wear) / Inspection / Tire Rotation illustration
  3. If the steering continues to pull to one side, rotate the front right and left tires again, and perform a road test.
    Maintenance — Chassis / Tire (pressure & tread wear) / Inspection / Tire Rotation illustration
  4. If the steering continues to pull to the opposite side, replace the front wheels with new ones.
    Maintenance — Chassis / Tire (pressure & tread wear) / Inspection / Tire Rotation illustration

Rear Differential Carrier Oil Lubricant

Lubricant

Rear differential carrier (AWD)

Item Lubricant Quantity
Rear differential carrier oil Hypoid gear oil SK HCT-5 gear oil 75W/85 or equivalent About 0.58 ℓ
(0.15 U.S.gal., 0.52 U.S.qt., 0.51 Imp.qt.)

Rear Differential Carrier Oil Inspection

Inspection

  1. Check for traces of oil leakage around the filler plug.
  2. Remove the filler plug and check that gear oil is visible through the filler plug hole (A).
    Maintenance — Chassis / Rear Differential Carrier Oil / Inspection illustration
    Note
    If gear oil is not visible, fill gear oil.

Rear Differential Carrier Oil Replacement

Replacement

  1. Remove the drain plug (A) and drain gear oil, and then reinstall the drain plug (A).

    Tightening torque : 49.0 - 69 N·m

    Maintenance — Chassis / Rear Differential Carrier Oil / Replacement illustration
    Note
    Do not reuse the drain plug packing (B).
    Maintenance — Chassis / Rear Differential Carrier Oil / Replacement illustration
  2. Remove the filler plug (A) and gasket (B).
    Maintenance — Chassis / Rear Differential Carrier Oil / Replacement illustration
    Note
    Do not reuse the filler plug gasket (B).
  3. Fill new gear oil through the filler plug hole (A).
    Oil Type : Hypoid gear oil MS517-15 GTC 75W/85 (GL-5) (SK HCT-5 Gear Oil 75W/85 or equivalent) Oil Capacity (L) : About 0.58 ± 0.05 ℓ (0.15 U.S.gal., 0.52 U.S.qt., 0.51 Imp.qt.)
    Maintenance — Chassis / Rear Differential Carrier Oil / Replacement illustration
  4. Install the filler plug (A) and filler gasket (B).

    Tightening torque : 39.2 - 59 N·m

    Maintenance — Chassis / Rear Differential Carrier Oil / Replacement illustration
    Note
    Do not reuse the filler gasket (B).
  5. Start the vehicle and check for oil leaks from the differential carrier assembly.
    Note
    If oil leaks, disassemble and reassemble the differential carrier assembly and re-inspect.

Transfer Oil Lubricant

Lubricant

Fluid

Item Capacity
Transfer oil About 0.50 ℓ
(0.13 U.S.gal., 0.52 U.S.qt, 0.43 Imp.qt.)

Grease

Item Recommended grease Capacity
Transfer spline TECHRUBE MEGAMAX-ALPHA, CASMOLY CSG 101 M or equivalent 2.0 - 5.0 g
Coupling spline 2.0 - 6.0 g

Transfer Oil Inspection

Inspection

Information
Inspect and replace transfer oil every 4 years or 60,000 km (37,000 mile).
  1. Remove the engine room under cover. G 1.6 MPI GAMMA (Refer to Engine Mechanical System - "Engine Room Under Cover") G 1.6 T-GDI GAMMA II (Refer to Engine Mechanical System - "Engine Room Under Cover") G 2.0 MPI NU (Refer to Engine Mechanical System - "Engine Room Under Cover")
  2. Remove the filler plug (A).
    Maintenance — Chassis / Transfer Oil / Inspection illustration
  3. Remove the drain plug (A), wait for at least 10 minutes until the oil is fully drained, and then reinstall the drain plug.

    Tightening torque : 39.2 - 59 N·m

    Maintenance — Chassis / Transfer Oil / Inspection illustration
    Note
    • Do not reuse the drain plug gasket (A).
      Maintenance — Chassis / Transfer Oil / Inspection illustration
    • Apply Loctite 592 or equivalent on thread (A) before installing new drain plug.
      Maintenance — Chassis / Transfer Oil / Inspection illustration
  4. Check the amount of drained oil and fill the specified amount of oil through the filler plug hole.
    Capacity : About 0.50 ℓ (0.13 U.S.gal., 0.52 U.S.qt, 0.43 Imp.qt.) Recommended : Hypoid gear oil API GL-5 SAE 75W/85 (SK HCT-5 gear oil 75W/85) or equivalent
  5. Install the filler plug (A).

    Tightening torque : 39.2 - 59 N·m

    Maintenance — Chassis / Transfer Oil / Inspection illustration
    Note
    Do not reuse the filler plug gasket (A).
    Maintenance — Chassis / Transfer Oil / Inspection illustration
  6. Install the engine room under cover. G 1.6 MPI GAMMA (Refer to Engine Mechanical System - "Engine Room Under Cover") G 1.6 T-GDI GAMMA II (Refer to Engine Mechanical System - "Engine Room Under Cover") G 2.0 MPI NU (Refer to Engine Mechanical System - "Engine Room Under Cover")

Transfer Oil Replacement

Replacement

  1. Remove the engine room under cover. G 1.6 MPI GAMMA (Refer to Engine Mechanical System - "Engine Room Under Cover") G 1.6 T-GDI GAMMA II (Refer to Engine Mechanical System - "Engine Room Under Cover") G 2.0 MPI NU (Refer to Engine Mechanical System - "Engine Room Under Cover")
  2. Remove the drain plug (A) and drain transfer oil, and then reinstall the drain plug (A).

    Tightening torque : 39.2 - 59 N·m

    Maintenance — Chassis / Transfer Oil / Replacement illustration
    Note
    • Do not reuse the drain plug gasket (A).
      Maintenance — Chassis / Transfer Oil / Replacement illustration
    • Apply Loctite to the thread (A) before installing a new drain plug.
      Maintenance — Chassis / Transfer Oil / Replacement illustration
  3. Remove the filler plug (A) and refill with oil.
    Capacity : Fill to the bottom of the oil filler hole Recommended : Hypoid gear oil API GL-5 SAE 75W/85 (SK HCT-5 gear oil 75W/85) or equivalent
    Maintenance — Chassis / Transfer Oil / Replacement illustration
  4. Install the filler plug (A).

    Tightening torque : 39.2 - 59 N·m

    Maintenance — Chassis / Transfer Oil / Replacement illustration
    Note
    Do not reuse the filler plug gasket (A).
    Maintenance — Chassis / Transfer Oil / Replacement illustration
  5. Install the engine room under cover. G 1.6 MPI GAMMA (Refer to Engine Mechanical System - "Engine Room Under Cover") G 1.6 T-GDI GAMMA II (Refer to Engine Mechanical System - "Engine Room Under Cover") G 2.0 MPI NU (Refer to Engine Mechanical System - "Engine Room Under Cover")