Driving

BSM (Blind Spot Monitor)

3steps
~18min
2/5difficulty
Done 0 of 3

Blind Spot Monitor overview

The Blind Spot Monitor (BSM) system has 2 functions:

  • BSM function (Blind Spot Monitor)
    Helps the driver decide whether it is safe to change lanes
  • RCTA function (Rear Cross Traffic Alert)
    Helps the driver when reversing

These functions use the same sensors.

Toyota CH-R. Utilisation des systèmes d'aide à la conduite
  1. Outside rear view mirror indicators
BSM function: When a vehicle is detected in a blind spot of the outside rear view mirrors, or approaching quickly from behind and in a blind spot, the indicator on the corresponding outside rear view mirror turns on. If you operate the turn signal lever toward the detected side, the indicator on the outside rear view mirror flashes. RCTA function: When a vehicle is detected approaching from the right or left behind the vehicle, both indicators on the outside rear view mirrors flash.
  1. Multi-information display
    Turns the BSM function/RCTA function on and off. The RCTA function is available when the BSM function is on.
  2. RCTA buzzer (RCTA function only)
    If a vehicle is detected approaching from the right or left behind the vehicle, a buzzer sounds. The buzzer also sounds for approximately 1 second immediately after the BSM function is operated to turn the system on.
  3. "BSM" indicator/"RCTA" indicator
    When the BSM function/RCTA function is turned on, the indicator comes on.

Turning the BSM function/RCTA function on and off

1. Press theToyota CH-R. orToyota CH-R. Using the instrument panel selector, selectToyota CH-R. Utilisation des systèmes d'aide à la conduite.

2. PressToyota CH-R. orToyota CH-R. Using the instrument panel selector, selectToyota CH-R. Utilisation des systèmes d'aide à la conduite.

3. PressToyota CH-R. orToyota CH-R. Using the instrument panel selector, selectToyota CH-R. Utilisation des systèmes d'aide à la conduiteorToyota CH-R. Utilisation des systèmes d'aide à la conduite.

■ Visibility of the outside rear view mirror indicators When sunlight is very bright, the outside rear view mirror indicator may be difficult to see.

■ Audibility of the RCTA warning sound The RCTA warning sound may be difficult to hear in a noisy environment, especially if the audio system volume is high.

■ When the message "BSM not available" is displayed on the multi-information display Water, snow, mud, etc. may have accumulated in the part of the bumper where the sensor is located.

Clearing the bumper area where the sensor is located of any accumulated water, snow, mud, etc. should restore normal operation.

The sensor may also not operate normally in extremely hot or extremely cold weather.

■ When the message "BSM system malfunction. See your dealer." is displayed on the multi-information display The sensor may be faulty or misaligned. Have the vehicle inspected by a Toyota dealer, an authorized Toyota repairer, or any reliable repairer.

WARNING

■ Caring for the radar sensors A blind spot monitor sensor is installed inside the rear bumper on each side of the vehicle, left and right. Observe the following precautions to ensure the blind spot monitor operates correctly.

Toyota CH-R. Utilisation des systèmes d'aide à la conduite
  • Always keep the sensors and the surrounding bumper area clean. If a sensor or the surrounding part of the rear bumper is dirty or covered with snow, the blind spot monitor may not operate and a warning message may be displayed.
    In this case, clean off the dirt or snow from the bumper and drive the vehicle for about 10 minutes while making sure the BSM operating conditions are met.
    If the warning message does not go off, have the vehicle inspected by a Toyota dealer, an authorized Toyota repairer, or any reliable repairer.

  • Do not subject the sensors or the surrounding part of the rear bumper to strong impacts.

    If a sensor is moved out of position, even slightly, the system may not operate normally and vehicles may not be detected correctly.

    In the following situations, have your vehicle inspected by a Toyota dealer, an authorized Toyota repairer, or any reliable repairer.

    • A sensor or the surrounding area has been subjected to a strong impact.

    • The area surrounding a sensor is scratched or deformed, or a part has come loose.

  • Do not disassemble the sensor.

  • Do not attach accessories or stick stickers to the sensor or the surrounding bumper area.

  • Do not modify the sensor or the surrounding bumper area.

  • Do not paint the rear bumper in a color other than the Toyota official color.