Interior Light

Interior Light Circuit

~4min read

DESCRIPTION

The main body ECU (multiplex network body ECU) controls the lighting operation as follows:

  • Reading Light Assembly
  • Dome light assembly No. 1

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

  • Check the fuses for the circuits related to this system before performing the following procedure.
  • Before replacing the main body ECU (multiplex network body ECU), refer to the registration section*1.

    Click here

    • *1: with Smart Key System

HINT:

The DOME CUT relay supplies power to the interior lights. If all the lights supplied by the DOME CUT relay do not illuminate, check the interior light power supply circuit first.

Click here

PROCEDURE

  1. PERFORM ACTIVE TEST USING TECHSTREAM

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn on the Techstream.

(d) Select the following menu items: Body Electrical / Main Body / Active Test.

(e) Perform the Active Test by following the Techstream instructions.

Body Electrical > Main Body > Active Test

Tester display

Item

Control Range

Diagnostic Note

Illuminated Entry System

Turns on the lights that are controlled by the lighting-on-approach system.*

ON or OFF

-

  • *: Refer to the System Description section for the lights that are controlled by the lighting-on-approach system.

    Click here

Body Electrical > Main Body > Active Test

Illuminated Entry System

OK:

All lights controlled by the lighting-on-approach system illuminate.

OK

GO TO APPLICABLE SYSTEM AS INDICATED IN THE PROBLEM SYMPTOMS TABLE

NG
  1. INSPECT MAP LIGHT ASSEMBLY

(a) Remove the reading light assembly.

Click here

(b) Inspect the reading light assembly.

Click here

NG

REPLACE MAP LIGHT ASSEMBLY

OK
  1. CHECK WIRE HARNESS AND CONNECTOR (READING LIGHT ASSEMBLY - NO. 1 ROOM LIGHT ASSEMBLY)

(a) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

R2-12 (+B1) - R2-4 (RLMP)

No. 1 room light switch in DOOR position

Below 1 Ω

No. 1 room light switch in ON position

10 kΩ minimum

R2-12 (+B1) or R2-4 (RLMP) - Body ground

No. 1 room light switch in DOOR position

10 kΩ minimum

NG

REPLACE NO. 1 ROOM LIGHT ASSEMBLY

OK
  1. CHECK WIRE HARNESS AND CONNECTOR (DOME CUT RELAY - READING LIGHT ASSEMBLY)

(a) Measure the voltage according to the value(s) shown in the table below.

Standard voltage:

Tester Connection

Condition

Specified Condition

R2-12 (+B1) - Body ground

Battery saver function does not operate

11 à 14 V

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK WIRE HARNESS AND CONNECTOR (READING LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

(a) Disconnect connector 3D from the instrument panel junction block assembly.

(b) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

R2-10 (DOOR) - 3D-29

Always

Below 1 Ω

R2-10 (DOOR) or 3D-29 - Body ground

Always

10 kΩ minimum

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

(a) Remove the instrument panel junction block assembly.

Click here

(b) Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click here

(c) Measure the resistance according to the value(s) in the table below.

*a

Component without wire harness connected

(instrument panel junction block assembly)

-

-

Standard resistance:

Tester Connection

Condition

Specified Condition

3D-29 - MB-1 (ILE)

Always

Below 1 Ω

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY