Interior Light

Operation Check

~5min read

OPERATION CHECK

CHECK ILLUMINATED ENTRY SYSTEM OPERATION

NOTICE:

Perform this check with the customization settings set to the initial settings.

HINT:

Perform this check with the door switch of the reading light assembly in ON.

Lights controlled by the illuminated entry system

Control

Condition

Lights that operate

Linked to operation area*1

With the engine switch in OFF and all doors closed and locked, enter an exterior detection area while carrying the electronic key transmitter, and check that the operating lights turn on for approximately 15 seconds, then turn off.

  • Reading Light Assembly
  • Dome light assembly No. 1

Linked to Door Lock/Unlock

With the ignition switch in OFF and all doors closed and locked, unlock one of the front doors using an unlock operation (key-linked, remote, or unlock-on-opening operation), and check that the operating lights turn on for 15 seconds, then turn off.

  • Reading Light Assembly
  • Dome light assembly No. 1
  • Interior light assembly No. 1 (door courtesy light)*3
  • Instrument cluster finish panel garnish (cup holder light)*3

Linked to door opening/closing

With the ignition switch in OFF and all doors closed, open one of the front doors and check whether the operating lights turn on. When the operating lights are on, close all doors and check whether the operating lights turn off after approximately 15 seconds.

  • Reading Light Assembly
  • Dome light assembly No. 1
  • Interior light assembly No. 1 (door courtesy light)*3
  • Instrument cluster finish panel garnish (cup holder light)*3

With the engine switch in OFF and all doors closed, open one of the front doors and check whether the operating light turns on. When the operating light is on, close all doors and check whether the operating light turns off after approximately 40 seconds.*1

Engine switch illumination*1

With the ignition switch in ACC or ON, open a front door and check that the lights that operate come on. When the lights that operate are on, close all doors and check that the lights that operate turn off.

  • Reading Light Assembly
  • Dome light assembly No. 1

Linked to engine switch*1

Turn the engine switch from ON (ACC) or ON (IG) to OFF, and make sure the lights that operate come on for approximately 15 seconds and then turn off.

  • Reading Light Assembly
  • Dome light assembly No. 1
  • Interior light assembly No. 1 (door courtesy light)*3
  • Instrument cluster finish panel garnish (cup holder light)*3

Linked to ignition switch*2

Turn the ignition switch from ACC or ON to OFF, and make sure the lights that operate come on for approximately 15 seconds and then turn off.

  • Reading Light Assembly
  • Dome light assembly No. 1
  • Interior light assembly No. 1 (door courtesy light)*3
  • Instrument cluster finish panel garnish (cup holder light)*3

Gear engaged associated*3

With the ignition switch in ACC or ON, move the shift lever from P to another position, and make sure the light brightness decreases. When the light brightness has decreased, move the shift lever to P, and make sure the lights return to full brightness.

  • Interior light assembly No. 1 (door courtesy light)
  • Instrument cluster finish panel trim (cup holder light)
  • *1: with Smart Key System
  • *2: Without smart key system
  • *3: With door courtesy light

CHECK BATTERY SAVER CONTROL OPERATION

(a) The operation and conditions of this control are described below.

Control

Condition

Lights that operate

Basic operation

When 20 minutes have elapsed after the ignition switch was moved from ACC or ON to OFF and the operating lights have remained on, the lights turn off.

HINT:

Battery saver control is canceled when any of the following operations is performed before the lights turn off via battery saver control. Once the operation is performed, the lights remain on for 20 minutes, then the lights turn off.

  • The ignition switch is set to ACC or ON.
  • Any door is opened and then closed.
  • The luggage compartment door is opened and closed.
  • One of the doors is unlocked.
  • The key enters an exterior operation area.
  • Reading Light Assembly
  • Dome light assembly No. 1
  • Engine switch illumination*1
  • Interior light assembly No. 1 (door courtesy light)*2
  • Instrument cluster finish panel trim (cup holder light)*2

Automatic interior light cut-off operation

When 20 minutes have elapsed after the ignition switch was moved from ACC or ON to OFF and the operating lights have remained on, the lights turn off.

HINT:

Battery saver control is canceled when any of the following operations is performed before the lights turn off via battery saver control. Once the operation is performed, the lights remain on for 20 minutes, then the lights turn off.

  • The ignition switch is set to ACC or ON.
  • Reading Light Assembly
  • Dome light assembly No. 1
  • Luggage compartment light assembly No. 1
  • Courtesy light assembly
  • *1: with Smart Key System
  • *2: With door courtesy light