Door Courtesy Switch Circuit
DESCRIPTION
The Main Body ECU (Multiplex Network Body ECU) detects the status of the Door Courtesy Light Switch Assy.
WIRING DIAGRAM
PRECAUTION / NOTICE / HINT
NOTICE:
Before replacing the main body ECU (multiplex network body ECU), refer to the registration section*1.
Click here![]()
- *1: with Smart Key System
PROCEDURE
CHECK VALUE USING TECHSTREAM
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn on the Techstream.
(d) Select the following menus: Body Electrical / Main Body / Data List.
(e) Read the Data List by following the instructions on the Techstream.
Body Electrical > Main Body > Data ListTester display | Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
RR Door Courtesy SW |
Rear RH Door Sill Light Switch Assembly Signal |
ON or OFF |
ON: Right rear door open. OFF: Right rear door closed. |
- |
RL Door Courtesy SW |
Rear LH Door Sill Light Switch Assembly Signal |
ON or OFF |
ON: Left rear door open. OFF: Left rear door closed. |
- |
FR Door Courtesy SW |
Front RH Door Welcome Light Switch Assembly Signal |
ON or OFF |
ON: Front RH door open OFF: Front RH door closed |
- |
FL Door Courtesy SW |
Front LH Door Welcome Light Switch Assembly Signal |
ON or OFF |
ON: Front left door open OFF: Front left door closed |
- |
Tester display |
|---|
RR Door Courtesy SW |
RL Door Courtesy SW |
FR Door Courtesy SW |
FL Door Courtesy SW |
OK:
The normal conditions listed above are displayed.
Result:
Result | Proceed to |
|---|---|
OK |
A |
Front door courtesy light switch SW is malfunctioning |
B |
Front left door courtesy light switch SW is malfunctioning |
C |
Rear right door courtesy light switch SW is malfunctioning |
D |
Rear left door courtesy light switch SW is malfunctioning |
E |
| A | GO TO APPLICABLE SYSTEM AS INDICATED IN THE PROBLEM SYMPTOMS TABLE |
| C | GO TO STEP 4 |
| D | GO TO STEP 6 |
| E | GO TO STEP 9 |
|
CHECK FRONT RIGHT DOOR COURTESY LIGHT SWITCH ASSY
(a) Remove the front right door courtesy light switch assy.
Click here
![]()
(b) Check the front right door courtesy light switch assy.
Click here![]()
OK:
The front right door courtesy light switch assy is normal.
| NG | REPLACE FRONT RIGHT DOOR COURTESY LIGHT SWITCH ASSY |
|
CHECK HARNESS AND CONNECTOR (FRONT RIGHT DOOR COURTESY LIGHT SWITCH ASSY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
(a) Disconnect the F15 connector from the main body ECU (multiplex network body ECU).
(b) Measure the resistance according to the value(s) in the table below.
Standard resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
M54-1 - F15-27 (FRCY) |
Always |
Below 1 Ω |
M54-1 or F15-27 (FRCY) - Body ground |
Always |
10 kΩ minimum |
| OK | REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
CHECK FRONT LEFT DOOR COURTESY LIGHT SWITCH ASSY
(a) Remove the front left door courtesy light switch assy.
Click here
![]()
(b) Check the front left door courtesy light switch assy.
Click here![]()
OK:
The front left door courtesy light switch assy is normal.
| NG | REPLACE FRONT LEFT DOOR COURTESY LIGHT SWITCH ASSY |
|
CHECK HARNESS AND CONNECTOR (FRONT LEFT DOOR COURTESY LIGHT SWITCH ASSY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
(a) Disconnect the F15 connector from the main body ECU (multiplex network body ECU).
(b) Measure the resistance according to the value(s) in the table below.
Standard resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
M11-1 - F15-6 (FLCY) |
Always |
Below 1 Ω |
M11-1 or F15-6 (FLCY) - Body ground |
Always |
10 kΩ minimum |
| OK | REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
CHECK REAR RIGHT DOOR COURTESY LIGHT SWITCH ASSY
(a) Remove the rear right door courtesy light switch assy.
Click here
![]()
(b) Check the rear right door courtesy light switch assy.
Click here![]()
| NG | REPLACE REAR RIGHT DOOR COURTESY LIGHT SWITCH ASSY |
|
CHECK HARNESS AND CONNECTOR (REAR RIGHT DOOR COURTESY LIGHT SWITCH ASSY - INSTRUMENT PANEL JUNCTION BLOCK ASSY)
(a) Disconnect connector 3A from the instrument panel junction block assembly.
(b) Measure the resistance according to the value(s) in the table below.
Standard resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
M58-1 - 3A-31 |
Always |
Below 1 Ω |
M58-1 or 3A-31 - Body ground |
Always |
10 kΩ minimum |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
(a) Remove the instrument panel junction block assembly.
Click here
![]()
(b) Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Click here
![]()
(c) Measure the resistance according to the value(s) in the table below.
*a |
Component without wire harness connected (instrument panel junction block assembly) |
- |
- |
Standard resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
3A-31 - MB-2 (RCTY) |
Always |
Below 1 Ω |
| OK | REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
| NG | REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY |
CHECK REAR LEFT DOOR COURTESY LIGHT SWITCH ASSY
(a) Remove the rear left door courtesy light switch assy.
Click here
![]()
(b) Check the rear left door courtesy light switch assy.
Click here![]()
| NG | REPLACE REAR LEFT DOOR COURTESY LIGHT SWITCH ASSY |
|
CHECK HARNESS AND CONNECTOR (REAR LEFT DOOR COURTESY LIGHT SWITCH ASSY - INSTRUMENT PANEL JUNCTION BLOCK ASSY)
(a) Disconnect connector 3H from the Instrument Panel Junction Block Assy.
(b) Measure the resistance according to the value(s) in the table below.
Standard resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
M16-1 - 3H-24 |
Always |
Below 1 Ω |
M16-1 or 3H-24 - Body ground |
Always |
10 kΩ minimum |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
(a) Remove the instrument panel junction block assembly.
Click here
![]()
(b) Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Click here
![]()
(c) Measure the resistance according to the value(s) in the table below.
*a |
Component without wire harness connected (instrument panel junction block assembly) |
- |
- |
Standard resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
3H-24 - MB-13 (LCTY) |
Always |
Below 1 Ω |
| OK | REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
| NG | REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY |