Door Unlock Detection Switch Circuit
DESCRIPTION
The main body ECU (multiplex network body ECU) detects the state of the door unlock detection switch of each door.
WIRING DIAGRAM
PRECAUTION / NOTICE / HINT
NOTICE:
Before replacing the main body ECU (multiplex network body ECU), refer to the registration section*1.
Click here![]()
- *1: with Smart Key System
PROCEDURE
CHECK VALUE USING TECHSTREAM
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn on the Techstream.
(d) Select the following menus: Body Electrical / Main Body / Data List.
(e) Read the Data List by following the instructions on the Techstream.
Body Electrical > Main Body > Data ListTester display | Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
FR Door Lock Pos |
Front Right Door Unlock Detection Switch Signal |
LOCK or UNLOCK |
LOCK: Front right door locked. UNLOCK: Front right door unlocked. |
- |
FL Door Lock Pos |
Front Left Door Unlock Detection Switch Signal |
LOCK or UNLOCK |
LOCK: Front left door locked. UNLOCK: Front left door unlocked. |
- |
RR-Door Lock Pos SW |
Rear Left and Right Door Unlock Detection Switch Signal |
ON or OFF |
ON: Rear right or left door unlocked. OFF: Rear right and left doors locked. |
- |
RL-Door Lock Pos SW |
Rear Left and Right Door Unlock Detection Switch Signal |
ON or OFF |
ON: Rear right or left door unlocked. OFF: Rear right and left doors locked. |
- |
Tester display |
|---|
FR Door Lock Pos |
FL Door Lock Pos |
RR-Door Lock Pos SW |
RL-Door Lock Pos SW |
Result:
Result | Proceed to |
|---|---|
OK |
A |
"FL Door Lock Pos" is not normal |
B |
"FR Door Lock Pos" is not normal |
C |
"RL-Door Lock Pos SW" and "RR-Door Lock Pos SW" do not operate normally |
D |
| A | GO TO APPLICABLE SYSTEM AS INDICATED IN THE PROBLEM SYMPTOMS TABLE |
| C | GO TO STEP 5 |
| D | GO TO STEP 8 |
|
INSPECT FRONT LH DOOR LOCK ASSEMBLY WITH MOTOR
(a) Remove the front LH door lock assembly with motor.
Click here
![]()
(b) Inspect the front LH door lock assembly with motor.
Click here
![]()
OK:
The front LH door lock assembly with motor is normal.
| NG | REPLACE FRONT LH DOOR LOCK ASSEMBLY WITH MOTOR |
|
CHECK WIRE HARNESS AND CONNECTOR (FRONT LH DOOR LOCK ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND)
(a) Disconnect connector 3D from the instrument panel junction block assembly.
(b) Measure the resistance according to the value(s) in the table below.
Standard resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
J4-8 (LSSR) - 3D-13 |
Always |
Below 1 Ω |
J4-8 (LSSR) or 3D-13 - Body ground |
Always |
10 kΩ minimum |
J4-7 (E) - Body ground |
Always |
Below 1 Ω |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
(a) Remove the instrument panel junction block assembly.
Click here
![]()
(b) Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Click here
![]()
(c) Measure the resistance according to the value(s) in the table below.
*a |
Component without wire harness connected (instrument panel junction block assembly) |
- |
- |
Standard resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
3D-13 - MB-19 (LSFL) |
Always |
Below 1 Ω |
| OK | REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
| NG | REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY |
INSPECT FRONT RH DOOR LOCK ASSEMBLY WITH MOTOR
(a) Remove the front RH door lock assembly with motor.
Click here
![]()
(b) Inspect the front RH door lock assembly with motor.
Click here
![]()
OK:
The front RH door lock assembly with motor is normal.
| NG | REPLACE FRONT RH DOOR LOCK ASSEMBLY WITH MOTOR |
|
CHECK WIRE HARNESS AND CONNECTOR (FRONT RH DOOR LOCK ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND)
(a) Disconnect connector 3D from the instrument panel junction block assembly.
(b) Measure the resistance according to the value(s) in the table below.
Standard resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
I4-7 (LSSR) - 3D-12 |
Always |
Below 1 Ω |
I4-7 (LSSR) or 3D-12 - Body ground |
Always |
10 kΩ minimum |
I4-8 (E) - Body ground |
Always |
Below 1 Ω |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
(a) Remove the instrument panel junction block assembly.
Click here
![]()
(b) Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Click here
![]()
(c) Measure the resistance according to the value(s) in the table below.
*a |
Component without wire harness connected (instrument panel junction block assembly) |
- |
- |
Standard resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
3D-12 - MB-17 (LSFR) |
Always |
Below 1 Ω |
| OK | REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
| NG | REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY |
INSPECT REAR LH DOOR LOCK ASSEMBLY WITH MOTOR
(a) Remove the rear LH door lock assembly with motor.
Click here
![]()
(b) Inspect the rear LH door lock assembly with motor.
Click here
![]()
OK:
The rear LH door lock assembly with motor is normal.
| NG | REPLACE REAR LH DOOR LOCK ASSEMBLY WITH MOTOR |
|
CHECK WIRE HARNESS AND CONNECTOR (REAR LH DOOR LOCK ASSEMBLY WITH MOTOR - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND)
(a) Disconnect connector 3D from the instrument panel junction block assembly.
(b) Measure the resistance according to the value(s) in the table below.
Standard resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
L1-5 (LSSR) - 3D-14 |
Always |
Below 1 Ω |
L1-5 (LSSR) or 3D-14 - Body ground |
Always |
10 kΩ minimum |
L1-6 (E) - Body ground |
Always |
Below 1 Ω |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
INSPECT REAR RH DOOR LOCK ASSEMBLY WITH MOTOR
(a) Remove the rear RH door lock assembly with motor.
Click here
![]()
(b) Inspect the rear RH door lock assembly with motor.
Click here
![]()
OK:
The rear RH door lock assembly with motor is normal.
| NG | REPLACE REAR RH DOOR LOCK ASSEMBLY WITH MOTOR |
|
CHECK WIRE HARNESS AND CONNECTOR (REAR RH DOOR LOCK ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND)
(a) Measure the resistance according to the value(s) in the table below.
Standard resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
K1-9 (LSSR) - 3D-14 |
Always |
Below 1 Ω |
K1-9 (LSSR) or 3D-14 - Body ground |
Always |
10 kΩ minimum |
K1-10 (E) - Body ground |
Always |
Below 1 Ω |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
(a) Remove the instrument panel junction block assembly.
Click here
![]()
(b) Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Click here
![]()
(c) Measure the resistance according to the value(s) in the table below.
*a |
Component without wire harness connected (instrument panel junction block assembly) |
- |
- |
Standard resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
3D-14 - MB-5 (LSR) |
Always |
Below 1 Ω |
| OK | REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
| NG | REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY |