Toyota Land Cruiser Quiz
Body Electrical

Inspection

In this manual: Body Electrical
Introduction — 13Preparation — 19Service specifications — 19Engine Mechanical — 28Automatic Transmission — 22Body Electrical — 373Brake — 34Propeller Shaft — 7Transfer — 24Motor shift control system — 1Steering — 34Ignition — 7Charging — 9Emission Control — 6Cooling — 17Starting — 12Lubrication — 13Maintenance — 7Chassis — 1Disassembly — 1
~3min read
5special tools
010203040507.56N·mlb·ft
Tightening torque found on this page

1. INSPECT INJECTOR INJECTION

INSPECT INJECTOR INJECTION

CAUTION: Keep injector clean of sparks during the test.

INSPECT INJECTOR INJECTION

(a) Disconnect the fuel inlet hose (fuel tube connector) from the fuel filter.

CAUTION:

  • Perform disconnecting operations of the fuel tube connector (quick type) after reading the precautions (SF-1 ).
  • Prevent the retained pressure in the fuel pipe line from splashing inside the engine compartment.
INSPECT INJECTOR INJECTION

(b) Use a new fuel main hose and take out the fuel tube connector from its hose.

Part No. 23271-50150

INSPECT INJECTOR INJECTION

(c) Connect SST (hose) and fuel tube connector to the fuel filter outlet.

SST 09268-41047

CAUTION: Perform connecting operations of the fuel tube connector (quick type) after reading the precautions (SF-1 ).

HINT: Use the vehicle's fuel filter.

INSPECT INJECTOR INJECTION

(d) Remove the pressure regulator from the delivery pipe.

(e) Install the O-ring to the fuel inlet of the pressure regulator.

(f) Connect SST (hose) to the fuel inlet of the pressure regulator with SST (union) and the 2 bolts.

SST 09268-41047 (09268-41091)

Torque: 7,5 N·m

(g) Connect the fuel return hose to the fuel outlet of the pressure regulator.

INSPECT INJECTOR INJECTION

(h) Install the O-ring to the injector.

(i) Connect SST (adaptor and hose) to the injector, and hold the injector and union with SST (clamp).

SST 09268-41047 (09268-41110, 09268-41300)

(j) Put the injector into the graduated cylinder.

CAUTION: Install a suitable vinyl hose onto the injector to prevent gasoline from splashing out.

INSPECT INJECTOR INJECTION

(k) Connect the TOYOTA hand-held tester or OBD II scan tool to the DLC3.

(l) Connect the battery negative (-) cable to the battery.

(m) Turn the ignition switch ON, and press the TOYOTA hand-held tester or OBD II scan tool main switch ON.

NOTICE: Do not start the engine.

(n) Select ACTIVE TEST mode on the TOYOTA hand-held tester or OBD II scan tool.

(o) Please refer to the TOYOTA hand-held tester or OBD II scan tool operator's manual for further details.

(p) If you have no TOYOTA hand-held tester or OBD II scan tool, connect the positive (+) and negative (-) leads from the battery to the fuel pump connector (SF-7 ).

INSPECT INJECTOR INJECTION

(q) Connect SST (wire) to the injector and the battery for 15 seconds, and measure the injection volume with a graduated cylinder. Test each injector 2 or 3 times.

SST 09842-30070

Volume: 56 - 69 cm3 (3.4 - 4.2 cu in.) per 15 seconds

Difference between each injector: 13 cm3 (0.8 cu in.) or less

If the injection volume is not as specified, replace the injector.

2. INSPECT LEAKAGE

INSPECT LEAKAGE

(a) In the condition above, disconnect the tester probes of SST (wire) from the battery and check the fuel leakage from the injector.

SST 09842-30070

Fuel drop: 1 drop or less per 12 minutes

(b) Turn the ignition switch OFF.

(c) Disconnect the negative (-) terminal cable from the battery.

(d) Remove SST and fuel tube connector.

SST 09268-41047, 09842-30070

(e) Disconnect the TOYOTA hand-held tester or OBD II scan tool from the DLC3.

(f) Reconnect the fuel inlet pipe (fuel tube connector) to the fuel filter.

CAUTION: Perform connecting operations of the fuel tube connector (quick type) after observing the precautions (SF-1 ).

Test yourself

A quick Toyota Land Cruiser quiz: every answer comes with an explanation and a link to the manual page.