Direct Electro Hydraulic Actuator Coupling Description and Operation
Description
The AWD ECU accurately adjusts the tightening force of the AWD-coupled multi-plate clutch by determining the road conditions and driving conditions through various sensor signals inputted, thus controlling the magnitude of the drive transmitted to the rear wheels. AWD controlling (by Driving condition)
At cruising speed (Automatic mode) Distribute most of the driving power to front wheels.
At cornering (Automatic mode) Distribute driving power to rear wheels according to turning radius and vehicle speed.
At slip condition (Automatic mode) When the front wheels slip, the driving power is distributed to the rear wheels depending on the amount of slip.
Terrain mode Maximize power for a drive through a rough road.
Operation
Direct Electro Hydraulic Actuator Coupling Operation
[Inactive] [Active] Operating Sequence 1. AWD ECU receives CAN signals from the vehicle's sensors. 2. AWD ECU calculates the necessary amount of rear-wheel torque and sends the corresponding driving current to the actuator (electronic motor and hydraulic pump). 3. Hydraulic pressure generated by the actuator moves the piston. 4. Friction from the piston's movement engages the clutch. 5. Deliver power to the rear wheels
Direct Electro Hydraulic Actuator Coupling Removal and Installation
Removal
There is no need to check, replenish or replace the coupling assembly oil as it is shipped from the factory filled with coupling oil. (No maintenance required, lifetime fluid)
Maintain a horizontal position when removing or installing, or replacing the coupling assembly. (Refer to caution label (A).)
Disconnect the battery negative ( - ) terminal.
Remove the propeller shaft assembly. (Refer to Propeller Shaft Assembly - "Propeller Shaft")
Disconnect the pressure sensor connector (A).
Disconnect the hydraulic motor connector (A).
Remove the DEHAC assembly (A) after removing the bolts.
Tightening torque : 56.9 - 65 N·m
Installation
Install in reverse order of removal.
Apply a small amount of high-pressure grease to the spline hole (A) before installing the DEHAC assembly. Recommended grease : TECHRUBE MEGAMAX-ALPHA, CASMOLY CSG 101 M or equivalent Capacity : 2 - 6 g
Be careful not to damage the oil seal (B) when assembling the DEHAC assembly and rear differential carrier assembly.
Do not reuse the propeller shaft mounting bolts (Loctite applied)
Match the marks (A) before tightening bolts (B) when installing propeller shaft.
If the coupling is replaced with a new one or there is abnormal vibration, balance the propeller shaft with a propeller shaft balancing equipment.
Initialize the clutch wear value of the AWE ECU using KDS after replacing the DEHAC assembly. (Refer to AWD Control System - "Adjustment")
Oil Hydraulic Motor (Actuator) Description and Operation
Description
The AWD ECU operates the hydraulic motor(actuator) (A) installed on DEHAC to make hydraulic pressure to press the multi-disc clutch to supply torque to the rear wheel. the torque varies depending on the degree of compression of the multi-disc clutch according to the amount of hydraulic pressure.
Oil Hydraulic Motor (Actuator) On Vehicle Inspection
On Vehicle Inspection
If a DTC code about a hydraulic motor (actuator) is detected, inspect it by following hydraulic motor inspection procedures.
Hydraulic Motor Inspection Procedures
Oil Hydraulic Motor (Actuator) Removal
Removal
Remove the DEHAC (Direct Electro Hydraulic Actuator Coupling). (Refer to Coupling Assembly - "Direct Electro Hydraulic Actuator Coupling" )
Maintain the removed DEHAC in vertical.
Maintain the hydraulic motor (actuator) in vertical when removing or installing.
Maintain it in vertical holding by the assistant or using a tool (A).
Be careful not to damage the input shaft side (B).
If coupling oil leaked, replace the DEHAC assembly with a new one. (Replacement or supplementation is not recommended due to the specifications and quantity of filling of coupling oil have a significant impact on performance and durability.)
Precautions for Hydraulic Motor Service to Prevent Coupling Oil Leakage (Play ▶)
Video: Precautions for Hydraulic Motor Service to Prevent Coupling Oil Leakage
Notes When Refering Video This video provides guidance for understanding complex or hard-to-follow procedures by showing each step clearly. As needed, the video also provides clear guidance on essential procedural steps, including adjustment and diagnostic processes, the use of SSTs, and precautions to avoid component damage.
This video is created using common specifications and may differ from the actual vehicle.
The location and repair procedures of the parts may vary depending on vehicle model, model year, region, and specifications.
Check the KDS guide for detailed information on how to use the KDS.
Check the manual for detailed maintenance procedures.
Unauthorized reproduction, distribution, or sharing of this video is prohibited.
Remove the hydraulic motor (A) after removing the bolts.
Tightening torque : 9.8 - 11,8 N·m
Drain remaining oil to the inside the coupling assembly as much as possible, before removing the hydraulic motor (A). (about 5 - 10 seconds)
Oil Hydraulic Motor (Actuator) Installation
Installation
Wipe the foreign materials on the installing surface (A) with a clean cloth.
Check the hydraulic motor (actuator) O-ring (A).
Be careful not to allow foreign objects to enter the housing and hydraulic motor.
Install the hydraulic motor (A) and tighten the bolts.
When installing the hydraulic motor, make sure that the hydraulic connector is facing outward from the coupling.
Tightening torque : 9.8 - 11,8 N·m
Oil may flow back from through the air breather hole (A) by O-ring assembling pressure when installing the hydraulic motor.
To prevent additional oil backflow of the air breather hole, make sure to turn and place it on the floor as shown below.
Wipe the spilled oil around the coupling with a clean cloth.
Install the DEHAC assembly. (Refer to Coupling Assembly - "Direct Electro Hydraulic Actuator Coupling" )
Pressure Sensor Description and Operation
Description
The AWD ECU receives pressure values from the pressure sensor (A) mounted on the electronically controlled hydraulic coupling and controls the motor pump so that the target hydraulic pressure corresponding to the rear wheel distribution torque to be controlled is generated.
Pressure Sensor On Vehicle Inspection
On Vehicle Inspection
If a DTC code about a pressure sensor is detected, inspect it by following pressure sensor inspection procedures.
Pressure Sensor Inspection Procedures
Pressure Sensor Resistance Measurement
Disconnect the battery negative ( - ) terminal.
Disconnect the pressure sensor connector (A).
Measure the resistance between the pressure sensor pins.
Check the resistance values measured in accordance with Table 1. [Table 1]
Terminal
Resistance
Pin 2 – 3
2.755 - 4.133 kΩ
Pin 1 - 3
1.892 - 2.838 kΩ
Pin 1 - 2
1.714 - 2.838 kΩ
Pressure Sensor Removal and Installation
Removal
Disconnect the battery negative ( - ) terminal.
Disconnect the pressure sensor connector (A).
Remove the pressure sensor (A).
Tightening torque : 10.8 - 14,7 N·m
Installation
Check the pressure sensor for clean before installing.