Parking Assist / Monitor System

Data List / Active Test

~10min read

DATA LIST / ACTIVE TEST

DATA LIST

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not determine whether a part is faulty based only on these reference values.

HINT:

The Techstream Data List allows you to read the values or status of switches, sensors, actuators and other components without removing any parts. This non-intrusive check can be very useful, since intermittent conditions or signals can be identified before parts or wiring are moved. Reading the Data List during troubleshooting saves time in diagnosis.

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn on the Techstream.

(d) Select the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Data List.

(e) Read the Data List by following the instructions on the Techstream.

Body Electrical > Blind Spot Monitor Master > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

Main Switch

Blind Spot Monitor System Status

OFF or ON

OFF: Blind spot monitor system is off

ON: Blind spot monitor system is on

-

RCTA Switch Status

RCTA Function Status

OFF or ON

OFF: RCTA function disabled

OFF: RCTA function disabled

-

Warning Indicator Turning on(Master)

Left Outer Mirror Indicator Status

OFF or ON

  • OFF: Any status other than "ON"
  • ON: One of the following statuses
    • During initial check
    • Blind spot monitor system is on, vehicle detected on the left side, and left turn signal switch not operated

-

Warning Indicator Flashing(Master)

Left Outer Mirror Indicator Flashing Status

OFF or ON

OFF: Any status other than "ON"

ON: Blind spot monitor system is on, vehicle detected on the left side, and left turn signal switch operated

-

Main Switch Indicator Status

Status of blind spot monitor indicator on the blind spot monitor main switch (warning indicator deactivation switch assembly)

OFF or ON

OFF: Indicator off

ON: Indicator on

-

Warning Indicator Input Circuit Voltage

Outer Mirror Indicator Voltage

Min.: 0 V, Max.: 25.5 V

Indicator on: 2.5 to 7.5 V

Indicator off: Below 1 V

-

Warning Indicator Input Circuit Current

Outer Mirror Indicator Current

Min.: 0 mA, Max.: 255 mA

Indicator on: 5 to 100 mA

Indicator off: 0 mA

-

Turn Switch State

Turn Signal Switch Status

Left ON, Right ON or OFF

Left, when ON: Left turn signal switch in ON position

Right, when ON: Right turn signal switch in ON position

OFF: Turn signal switch in OFF position

-

Reverse (Only for AT/CVT)

Reverse Gear Engaged Signal Status

OFF or ON

OFF: Shift lever in any position other than R.

ON: Shift lever in R position

-

Vehicle Speed

Vehicle speed signal

Min.: -327.68 km/h, Max.: 328 km/h

Vehicle stopped: 0 km/h

-

Steering Angle

Steering angle sensor

Min.: -3,072 deg., Max.: 3,070.5 deg.

Turning left: Increases

Turning right: Decreases

-

Power Supply Voltage

Power supply voltage

Min.: 0 V, Max.: 49.951 V

Ignition switch ON: 11 to 14 V

-

Indicator Light Control State

Outer mirror indicator dimming state

Dimming OFF or dimming ON

Dimming OFF: Indicator is not dimmed

Dimming ON: Indicator dimmed

-

HV Flag

Hybrid vehicle

OFF or ON

OFF: Non-hybrid vehicle

ON: Hybrid vehicle

-

VGRS Flag

VGRS fitted

OFF or ON

OFF: VGRS not fitted

ON: VGRS fitted

-

Main SW Inspection Completeness Flag

Blind spot monitor main switch inspection completion

Incompl or Compl

Incompl: Inspection not completed

Compl: Inspection completed

-

Beam Axis Inspection Completeness Flag

Beam axis adjustment operation completion

Incompl or Compl

Incompl: Adjustment not completed

Compl: Adjustment completed

Changes to "Compl" when the blind spot monitor beam axis adjustment has been performed

Destination Undefined Flag

Destination determination

Unfixed or Fixed

Undefined: Sensor destination information not determined

Fixed: Sensor destination information is determined based on CAN destination information

-

Angle Adjustment by Auto Alignment

Angle adjusted by auto alignment

Min.: Less than -180 deg., Max.: More than 180 deg.

Angle adjusted by auto alignment is displayed

-

RCTA Equipped Information

RCTA equipped

OFF or ON

OFF: RCTA not equipped

ON: RCTA equipped

-

Master Side RCTA Function

Enables and disables the RCTA function

OFF or ON

ON: RCTA function enabled

OFF: RCTA function disabled

-

Mirror LED Control Frequency

Frequency of the door mirror indicator on the door mirror when blinking

Min.: 1 500 Hz, Max.: 2 400 Hz

Constant: 2 000 Hz

-

Setting of Warning Indicator Current (Dim OFF)

Current setting of the door mirror indicator when not dimmed

Min.: 0 mA, Max.: 100 mA

Constant: 0 to 100 mA

-

Setting of Warning Indicator Current (Dim ON)

Current setting of the door mirror indicator when dimmed

Min.: 0 mA, Max.: 100 mA

Constant: 0 to 100 mA

-

Mirror LED Duty Ratio (Blinking)

Duty ratio of the door mirror indicator when blinking

Min.: 0 %, Max.: 100 %

Always: 50%

-

Yaw Rate Sensor

Yaw rate sensor

Min.: Less than -125 deg/s, Max.: 124.612 deg/s

Turning right: -125 to 0 deg/s

Turning left: 0 to 124.612 deg/s

-

BSM Mirror Indicator Brightness

Outer Mirror Indicator Brightness

Dark or Bright

Dark: Outer mirror indicator brightness is low

Bright: Outer mirror indicator brightness is high

-

Number of DTC

Number of DTCs

Min.: 0, Max.: 255

When system is operating normally: 0

When a malfunction is detected: Above 0

-

Body Electrical > Blind Spot Monitor Slave > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

Warning Indicator Turning On (Slave)

Right outer mirror indicator ON status

OFF or ON

  • OFF: Any status other than "ON"
  • ON: One of the following statuses
    • During initial check
    • Blind spot monitor system ON, vehicle detected on right side and right turn signal switch not operated

-

Warning Indicator Flashing (Slave)

Right outer mirror indicator flashing status

OFF or ON

OFF: Any status other than "ON"

ON: Blind spot monitor system ON, vehicle detected on right side and right turn signal switch operated

-

Buzzer Sound Status

RCTA buzzer status (blind spot monitor buzzer)

OFF or ON

OFF: Buzzer does not sound

ON: Buzzer sounds

-

Warning Indicator Input Circuit Voltage

Outer Mirror Indicator Voltage

Min.: 0 V, Max.: 25.5 V

Indicator on: 2.5 to 7.5 V

Indicator off: Below 1 V

-

Warning Indicator Input Circuit Current

Outer Mirror Indicator Current

Min.: 0 mA, Max.: 255 mA

Indicator on: 5 to 100 mA

Indicator off: 0 mA

-

Buzzer Input Circuit Voltage

RCTA buzzer signal voltage (blind spot monitor buzzer)

Min.: 0 V, Max.: 25.5 V

Buzzer not sounding: 11 to 14 V

Buzzer sounding: Alternating between 0 and 14 V

-

Turn Switch State

Turn Signal Switch Status

Left ON, Right ON or OFF

Left, when ON: Left turn signal switch in ON position

Right, when ON: Right turn signal switch in ON position

OFF: Turn signal switch in OFF position

-

Reverse (Only for AT/CVT)

Reverse Gear Engaged Signal Status

OFF or ON

OFF: Shift lever in any position other than R.

ON: Shift lever in R position

-

Reverse (Only for MT)

Reverse Gear Engaged Signal Status

OFF or ON

OFF: Shift lever in any position other than R.

ON: Shift lever in R position

-

Vehicle Speed

Vehicle speed signal

Min.: -327.68 km/h, Max.: 328 km/h

Vehicle stopped: 0 km/h

-

Steering Angle

Steering angle sensor

Min.: -3,072 deg., Max.: 3,070.5 deg.

Turning left: Increases

Turning right: Decreases

-

Power Supply Voltage

Power supply voltage

Min.: 0 V, Max.: 49.951 V

Ignition switch ON: 11 to 14 V

-

Indicator Light Control State

Outer mirror indicator dimming state

Dimming OFF or dimming ON

Dimming OFF: Indicator is not dimmed

Dimming ON: Indicator dimmed

-

HV Flag

Hybrid vehicle

OFF or ON

OFF: Non-hybrid vehicle

ON: Hybrid vehicle

-

VGRS Flag

VGRS fitted

OFF or ON

OFF: VGRS not fitted

ON: VGRS fitted

-

Beam Axis Inspection Completeness Flag

Beam axis adjustment operation completion

Incompl or Compl

Incompl: Adjustment not completed

Compl: Adjustment completed

Changes to "Compl" when the blind spot monitor beam axis adjustment has been performed

Destination Undefined Flag

Destination determination

Unfixed or Fixed

Undefined: Sensor destination information not determined

-

Angle Adjustment by Auto Alignment

Angle adjusted by auto alignment

Min.: Less than -180 deg., Max.: More than 180 deg.

Angle adjusted by auto alignment is displayed

-

RCTA Equipped Information

RCTA equipped

OFF or ON

OFF: RCTA not equipped

ON: RCTA equipped

-

Mirror LED Control Frequency

Frequency of the door mirror indicator on the door mirror when blinking

Min.: 1 500 Hz, Max.: 2 400 Hz

Constant: 2 000 Hz

-

Setting of Warning Indicator Current (Dim OFF)

Current setting of the door mirror indicator when not dimmed

Min.: 0 mA, Max.: 100 mA

Constant: 0 to 100 mA

-

Setting of Warning Indicator Current (Dim ON)

Current setting of the door mirror indicator when dimmed

Min.: 0 mA, Max.: 100 mA

Constant: 0 to 100 mA

-

Mirror LED Duty Ratio (Blinking)

Duty ratio of the door mirror indicator when blinking

Min.: 0 %, Max.: 100 %

Always: 50%

-

Buzzer Control Frequency

RCTA (Rear Cross Traffic Alert) buzzer frequency when sounding

Min.: 1,000 Hz, Max.: 2,400 Hz

Constant: 2 000 Hz

-

Yaw Rate Sensor

Yaw rate sensor

Min.: Less than -125 deg/s, Max.: 124.612 deg/s

Turning right: -125 to 0 deg/s

Turning left: 0 to 124.612 deg/s

-

BSM Buzzer Volume Adjust

RCTA (Rear Cross Traffic Alert) buzzer volume

Low, Medium or High

Low: Buzzer volume is lower than average

Medium: Default buzzer volume

High: Buzzer volume is higher than average

-

Number of DTC

Number of DTCs

Min.: 0, Max.: 255

When system is operating normally: 0

When a malfunction is detected: Above 0

-