Operation Check
OPERATION CHECK
HINT:
The blind spot monitor beam axis confirmation is performed to verify whether the sensor beam axis is correct, and to adjust the beam axis using the reflector.
BLIND SPOT MONITOR BEAM AXIS CONFIRMATION
(a) When confirming the blind spot monitor beam axis, move the vehicle to a location where the space shown in the diagram can be secured.
NOTICE:
- Perform the check on level ground.
- Make sure there are no metal objects around the vehicle or on the ground.
- Unload the vehicle before starting the check.
- Confirm that the tire pressure is correct before starting the check.
- Do not place any objects other than the reflector (such as a large metal object) and do not allow any people to enter the check area (L 6 m (19.68 ft) x W 6 m (19.68 ft) x H 4 m (13.12 ft)), as shown in the diagram.
(b) Position the reflector.
(1) From the center of the rear bumper (center of the emblem), suspend a pointed weight and mark the vehicle's rear center point on the ground (mark A).
*a |
String |
*b |
Weight |
*c |
Center point |
- |
- |
HINT:
Lightly flick the string with your finger several times to make sure the string is aligned with mark A.
(2) From the center of the front bumper (center of the emblem), suspend a pointed weight and mark the vehicle's front center point on the ground (mark B).
*a |
String |
*b |
Weight |
*c |
Center point |
- |
- |
HINT:
Lightly flick the string with your finger several times to make sure the string is aligned with mark (B).
(3) Draw a vertical line from the front to the rear through marks (A) and (B) (front and rear center points).
(4) Print the following diagram on a large sheet of paper.
(5) Place the printout on the ground, aligning point A with the vehicle's longitudinal center line.
(6) Align a piece of string with line C and reference point D at a distance of 3,324 mm (10.9 ft) from point A.
(7) Adjust the reflector at point D shown in the diagram below.
SST: 09870-60000
09870-60010
SST: 09870-60040
NOTICE:
- Adjust the reflector so that its center is 797 mm (2.61 ft) above the ground.

- The center of the pyramid represents the reference point for determining the adjustment position and angle.

- Adjust the reflector as shown in the diagram so that the center of the pyramid faces the blind spot monitor sensor.
(c) Perform the blind spot monitor beam axis display procedure.
(1) Connect the Techstream to the DLC3.
(2) Turn the ignition switch ON.
(3) Turn the blind spot monitor system ON.
(4) Turn on the Techstream.
(1) Select the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Utility / BSM Master Beam Axis Display or BSM Slave Beam Axis Display.
Body Electrical > Blind Spot Monitor Master > UtilityBSM Master Beam Axis Display
Body Electrical > Blind Spot Monitor Slave > UtilityBSM Slave Beam Axis Display
(6) Check the results shown on the BSM beam axis display.
Acceptable range:
Item | Left Blind Spot Sensor (Master) | Right Blind Spot Sensor (Slave) |
|---|---|---|
Angle |
-3,55 à +3,55° |
-3,55 à +3,55° |
HINT:
If the results are outside the acceptable range, the reflector position may be incorrect, there may be a metal object near the check area, or the blind spot monitor sensor installation condition may be abnormal. Check the reflector position, the check area, and the blind spot monitor sensor installation condition, then perform the check again.
(d) Adjust the blind spot monitor beam axis.
(1) Select the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Utility / BSM Master Beam Axis Adjustment or BSM Slave Beam Axis Adjustment.
HINT:
If the values shown on the axis display are within the acceptable range, performing this adjustment compensates for any deviation from the normal value.
Body Electrical > Blind Spot Monitor Master > UtilityBSM Master Beam Axis Adjustment
Body Electrical > Blind Spot Monitor Slave > UtilityBSM Slave Beam Axis Adjustment
BLIND SPOT MONITOR SENSOR INSTALLATION CONDITION CHECK
NOTICE:
- Perform the check on level ground.
- Unload the vehicle before starting the check.
- Confirm that the tire pressure is correct before starting the check.
HINT:
The blind spot monitor sensor installation condition check is performed to verify, using a gauge, that the sensor is perpendicular to the floor surface (+/-3°) and that the sensor is 46 to 54° from the line parallel to the vehicle center line.
(a) Remove the rear bumper.
Click here![]()
(b) Attach a gauge similar to the one shown in the diagram to the outward-facing surface of the blind spot monitor sensor, and check that the measurement or angle is within the acceptable range to confirm that the blind spot monitor sensor is perpendicular to the floor surface (+/-3°).
HINT:
A digital angle gauge can also be used to check that the blind spot monitor sensor is perpendicular to the ground or within the acceptable range.
StandardA | B |
|
|---|---|---|
Left Blind Spot Sensor (Master) |
5.2 mm (0.206 in) |
-5.2 mm (-0.206 in) |
Right Blind Spot Sensor (Slave) |
5.2 mm (0.206 in) |
-5.2 mm (-0.206 in) |
X | Y |
|
|---|---|---|
Left Blind Spot Sensor (Master) |
3° |
-3° |
Right Blind Spot Sensor (Slave) |
3° |
-3° |
(c) Use the center lines of the sensor mounting stud bolts as a reference and check that the stud bolts are as shown in the diagram.
Standard:
Dimension x - w | Specified value |
|---|---|
y |
78 to 87 mm (3.07 to 3.43 in) |
Degree | Specified value |
|---|---|
A |
46 à 54° |
HINT:
If the results do not meet the specifications, the blind spot monitor sensor mounting area (flange, stud bolt) may be deformed. Make the necessary corrections.