Parking Assist / Monitor System

Freeze Frame Data

~7min read

FREEZE FRAME DATA

FREEZE FRAME DATA

(a) Each time a DTC is detected, the blind spot sensor records the current vehicle operating conditions (sensor) as freeze frame data.

INSPECT FREEZE FRAME DATA

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Set the blind spot monitor system to ON.

(d) Turn on the Techstream.

(e) Select the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Trouble Codes.

(f) Following the instructions displayed on the Techstream screen, display the freeze frame data for the selected DTC.

Body Electrical > Blind Spot Monitor Master

Tester display

Item

Range

Normal Condition

Diagnostic Note

Main Switch

Blind Spot Monitor System Status

OFF or ON

OFF: Blind spot monitor system is off

ON: Blind spot monitor system is on

-

RCTA Switch Status

RCTA Function Status

OFF or ON

OFF: RCTA function disabled

ON: RCTA function enabled

-

Warning Indicator Turning on(Master)

Left Outer Mirror Indicator Status

OFF or ON

  • OFF: Any status other than "ON"
  • ON: One of the following statuses
    • During initial check
    • Blind spot monitor system is on, vehicle detected on the left side, and left turn signal switch not operated

-

Warning Indicator Flashing(Master)

Left Outer Mirror Indicator Flashing Status

OFF or ON

OFF: Any status other than "ON"

ON: Blind spot monitor system is on, vehicle detected on the left side, and left turn signal switch operated

-

Main Switch Indicator Status

Blind spot monitor indicator status on the blind spot monitor main switch

OFF or ON

OFF: Indicator off

ON: Indicator on

-

Warning Indicator Input Circuit Voltage

Outer Mirror Indicator Voltage

Min.: 0 V, Max.: 25.5 V

Indicator on: 2.5 to 7.5 V

Indicator off: Below 1 V

-

Warning Indicator Input Circuit Current

Outer Mirror Indicator Current

Min.: 0 mA, Max.: 255 mA

Indicator on: 5 to 100 mA

Indicator off: 0 mA

-

Turn Switch State

Turn Signal Switch Status

Left ON, Right ON or OFF

Left, when ON: Left turn signal switch in ON position

Right, when ON: Right turn signal switch in ON position

OFF: Turn signal switch in OFF position

-

Reverse (Only for AT/CVT)

Reverse Gear Engaged Signal Status

OFF or ON

OFF: Shift lever in any position other than R.

ON: Shift lever in R position

-

Vehicle Speed

Vehicle speed signal

Min.: -327.68 km/h, Max.: 328 km/h

Vehicle stopped: 0 km/h

-

Steering Angle

Steering angle sensor

Min.: -3,072 deg., Max.: 3,070.5 deg.

Turning left: Increases

Turning right: Decreases

-

Power Supply Voltage

Power supply voltage

Min.: 0 V, Max.: 49.951 V

Ignition switch ON: 11 to 14 V

-

Indicator Light Control State

Outer mirror indicator dimming state

Dimming OFF or dimming ON

Dimming OFF: Indicator is not dimmed

Dimming ON: Indicator dimmed

-

Angle Adjustment by Auto Alignment

Angle adjusted by auto alignment

Min.: Less than -180 deg., Max.: More than 180 deg.

Angle adjusted by auto alignment is displayed

-

Yaw Rate Sensor

Yaw rate sensor

Min.: Less than -125 deg/s, Max.: 124.612 deg/s

Turning right: -125 to 0 deg/s

Turning left: 0 to 124.612 deg/s

-

Number of DTC

Number of DTC

Min.: 0, Max.: 255

When system is operating normally: 0

When a malfunction is detected: Above 0

-

Body Electrical > Blind Spot Monitor Slave

Tester display

Item

Range

Normal Condition

Diagnostic Note

Warning Indicator Turning On (Slave)

Right outer mirror indicator ON status

OFF or ON

  • OFF: Any status other than "ON"
  • ON: One of the following statuses
    • During initial check
    • Blind spot monitor system ON, vehicle detected on right side and right turn signal switch not operated

-

Warning Indicator Flashing (Slave)

Right outer mirror indicator flashing status

OFF or ON

OFF: Any status other than "ON"

ON: Blind spot monitor system ON, vehicle detected on right side and right turn signal switch operated

-

Buzzer Sound Status

RCTA buzzer status (blind spot monitor buzzer)

OFF or ON

OFF: Buzzer does not sound

ON: Buzzer sounds

-

Warning Indicator Input Circuit Voltage

Outer Mirror Indicator Voltage

Min.: 0 V, Max.: 25.5 V

Indicator on: 2.5 to 7.5 V

Indicator off: Below 1 V

-

Warning Indicator Input Circuit Current

Outer Mirror Indicator Current

Min.: 0 mA, Max.: 255 mA

Indicator on: 5 to 100 mA

Indicator off: 0 mA

-

Buzzer Input Circuit Voltage

RCTA buzzer signal voltage (blind spot monitor buzzer)

Min.: 0 V, Max.: 25.5 V

Buzzer not sounding: 11 to 14 V

Buzzer sounding: Alternating between 0 and 14 V

-

Turn Switch State

Turn Signal Switch Status

Left ON, Right ON or OFF

Left, when ON: Left turn signal switch in ON position

Right, when ON: Right turn signal switch in ON position

OFF: Turn signal switch in OFF position

-

Reverse (Only for AT/CVT)

Reverse Gear Engaged Signal Status

OFF or ON

OFF: Shift lever in any position other than R.

ON: Shift lever in R position

-

Reverse (Only for MT)

Not supported

OFF or ON

OFF: Shift lever in any position other than R.

ON: Shift lever in R position

-

Vehicle Speed

Vehicle speed signal

Min.: -327.68 km/h, Max.: 328 km/h

Vehicle stopped: 0 km/h

-

Steering Angle

Steering angle sensor

Min.: -3,072 deg., Max.: 3,070.5 deg.

Turning left: Increases

Turning right: Decreases

-

Power Supply Voltage

Power supply voltage

Min.: 0 V, Max.: 49.951 V

Ignition switch ON: 11 to 14 V

-

Indicator Light Control State

Outer mirror indicator dimming state

Dimming OFF or dimming ON

Dimming OFF: Indicator is not dimmed

Dimming ON: Indicator dimmed

-

Angle Adjustment by Auto Alignment

Angle adjusted by auto alignment

Min.: Less than -180 deg., Max.: More than 180 deg.

Angle adjusted by auto alignment is displayed

-

Yaw Rate Sensor

Yaw rate sensor

Min.: Less than -125 deg/s, Max.: 124.612 deg/s

Turning right: -125 to 0 deg/s

Turning left: 0 to 124.612 deg/s

-

Number of DTC

Number of DTC

Min.: 0, Max.: 255

When system is operating normally: 0

When a malfunction is detected: Above 0

-

CLEAR FREEZE FRAME DATA

NOTICE:

Clearing DTCs also clears freeze frame data.

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Set the blind spot monitor system to ON.

(d) Turn on the Techstream.

(e) Clear DTCs and freeze frame data.