Parking Assist / Monitor System

Precautions

~8min read

PRECAUTION

IGNITION SWITCH TERMS

(a) The type of ignition switch used varies depending on vehicle specifications. The terms listed in the table below are used in this section.

Term

Ignition Switch (Position)

Engine Switch (Condition)

Ignition Switch in OFF position

LOCK

OFF (Locked)

Ignition Switch in ACC position

ACC

ON (ACC)

Ignition Switch in ON position

ON

ON (IG)

Starting the engine

START

ON (Starting)

PRECAUTIONS FOR BLIND SPOT MONITOR SYSTEM

(a) The blind spot monitor function may not detect vehicles correctly under the following conditions:

(1) When the sensor is misaligned due to a severe impact to the sensor or its immediate surroundings.

(2) When mud, snow, ice, a sticker, etc. covers the sensor or the area around it on the rear bumper.

(3) When driving on a wet road with puddles, or in bad weather conditions such as rain, snow or fog.

(4) When multiple vehicles are approaching with only a small gap between them.

(5) When the distance between this vehicle and a following vehicle is short.

(6) When there is a significant difference in speed between this vehicle and a vehicle entering the detection area.

(7) When the speed difference between this vehicle and another vehicle changes.

(8) When a vehicle enters the detection area at about the same speed as this vehicle.

(9) When your vehicle starts moving after stopping while a vehicle is still in the detection area.

(10) When driving uphill and downhill on consecutive slopes, such as hills, road descents, etc.

(11) When driving on very winding roads, with several consecutive curves or uneven surfaces.

(12) When the lanes are wide or when driving on the edge of a lane, and the vehicle in the adjacent lane is far from this vehicle.

(13) When towing a trailer.

(14) When a bicycle carrier or any other accessory is attached to the rear of the vehicle.

(15) When there is a significant difference in height between this vehicle and a vehicle entering the detection area.

(16) Immediately after the blind spot monitor system is turned on.

HINT:

In this section, the term "this vehicle" refers to the vehicle equipped with this blind spot monitor system.

(b) The blind spot monitor function is not designed to detect the following types of vehicles or objects:

(1) Vehicles approaching from the opposite direction.

(2) Small motorcycles, bicycles, pedestrians, etc. *

(3) Vehicles following in the same lane. *

(4) Guardrails, walls, signs, parked vehicles and similar stationary objects. *

(5) Vehicles crossing 2 lanes away from this vehicle. *

  • *: Depending on the conditions, a vehicle and/or object may be detected.

(c) The blind spot monitor system may detect a vehicle and/or object unnecessarily more often under the following conditions:

(1) When the sensor is misaligned due to a severe impact to the sensor or its immediate surroundings.

(2) When the distance between this vehicle and a guardrail, wall, etc. that enters the detection zone is short.

(3) When driving uphill and downhill on consecutive slopes, such as hills, road descents, etc.

(4) When the traffic lanes are narrow, or when your vehicle is driving on the edge of the traffic lane and a vehicle in a lane other than the adjacent lanes enters the detection zone.

(5) When driving on very winding roads, with several consecutive curves, or on uneven surfaces.

(6) When the wheels are spinning or skidding.

(7) When the distance between your vehicle and a following vehicle is short.

(8) When a bicycle carrier or other accessory is installed at the rear of the vehicle.

(9) When towing a trailer.

(d) The RCTA function may not correctly detect vehicles under the following conditions:

(1) In bad weather, such as heavy rain, fog, snow, etc.

(2) When the sensor is misaligned due to a severe impact on the sensor or its immediate surroundings.

(3) When driving on a wet road with puddles, or in bad weather conditions such as rain, snow or fog.

(4) When multiple vehicles are approaching with only a small gap between them.

(5) When a vehicle approaches at high speed.

(6) When towing a trailer.

(7) When reversing on a slope with a large change in gradient.

(8) When reversing out of a parking space at a shallow angle.

(9) Immediately after the blind spot monitor system is turned on.

(10) Immediately after starting the engine with the blind spot monitor system switched ON.

(11) As soon as the RCTA system is switched ON.

(12) As soon as the engine is started while the RCTA system is switched ON.

(13) When the sensors cannot detect a vehicle due to obstructions.

(e) The RCTA function is not designed to detect the following types of vehicles or objects:

(1) Vehicles coming directly from behind.

(2) Vehicles that the sensors cannot detect due to obstructions.

(3) Guardrails, walls, signs, parked vehicles and similar stationary objects.*

(4) Small motorcycles, bicycles, pedestrians, etc.*

(5) Vehicles moving away from this vehicle.

(6) Vehicles approaching parking spaces near the vehicle.*

HINT:

In this section, the term "this vehicle" refers to the vehicle equipped with this blind spot monitor system.

  • *: Depending on the conditions, a vehicle and/or object may be detected.

(f) The RCTA function may detect a vehicle and/or object unnecessarily more often under the following conditions:

(1) When a vehicle passes alongside your vehicle.

(2) When the parking space faces a street and vehicles are driving on the road.

(3) When the distance between the vehicle and metallic objects, such as a guardrail, wall, road sign or parked vehicle, which may reflect radio waves toward the rear of the vehicle, is short.

HINT:

In this section, the term "this vehicle" refers to the vehicle equipped with this blind spot monitor system.

(g) Under the following conditions, the blind spot monitor system may record DTCs C1AC1 and C1AC2 by mistake:

(1) The vehicle is driven continuously with the blind spot monitor system switched ON while using a chassis roller tester, such as a speedometer tester, a combined speedometer and brake tester, or a chassis dynamometer.

(2) When mud, snow, ice, a sticker, etc. covers the sensor or the area around it on the rear bumper.

HANDLING OF THE RADAR SENSOR

(a) The blind spot monitor sensors are installed behind the left and right sides of the rear bumper, respectively. Observe the following instructions to ensure the blind spot monitor operates correctly.

(1) Always keep the sensors and the area around them on the rear bumper clean.

(2) Do not subject a sensor or its immediate surroundings on the rear bumper to a severe impact. If a sensor is moved, even slightly, the system malfunctions and the vehicle may not be detected correctly. Under the following conditions, inspect the sensor and the surrounding area.

  • A sensor or its surrounding area has been subjected to a severe impact.
  • The area around a sensor is scratched or dented, or part of it has come loose.

(3) Do not disassemble the sensor.

(4) Do not attach stickers to the sensor or to the area around it on the rear bumper.

(5) Do not modify the sensor or the area around it on the rear bumper.

(6) Do not paint the rear bumper in a color other than Toyota's official colors.

(7) Do not drop the sensor or subject it to a severe impact, as it is a high-precision device.

(8) Do not reuse a sensor that has been dropped or subjected to a severe impact.