Toyota Land Cruiser Quiz
Body Electrical

Installation

In this manual: Body Electrical
Introduction — 13Preparation — 19Service specifications — 19Engine Mechanical — 28Automatic Transmission — 22Body Electrical — 373Brake — 34Propeller Shaft — 7Transfer — 24Motor shift control system — 1Steering — 34Ignition — 7Charging — 9Emission Control — 6Cooling — 17Starting — 12Lubrication — 13Maintenance — 7Chassis — 1Disassembly — 1
~2min read
1special tools
0204060801005944N·mlb·ft
Tightening torque found on this page

1. INSTALL AXLE HUB TO STEERING KNUCKLE

(a) Place the axle hub with disc to the steering knuckle.

NOTICE: Be careful not to damage the ABS speed sensor rotor and oil seal.

(b) Install the outer bearing.

(c) Install the claw washer.

2. ADJUST PRELOAD

ADJUST PRELOAD

(a) Install the adjusting nut and using SST, tighten it.

SST 09607-60020 Torque: 59 N·m

(b) Turn the axle hub several times to settle down the bearing.

(c) Using SST, loosen the adjusting nut until it can rotate by hand.

SST 09607-60020

(d) Using SST, retighten the adjusting nut.

SST 09607-60020

Torque: 4.3 - 6,5 N·m

HINT: Check that there is no looseness on the bearing.

ADJUST PRELOAD

(e) Using a spring tension gauge, measure the preload.

Preload (at starting): 42 - 67 N (4.3 - 6.8 kgf, 9.5 - 15.0 lbf)

3. INSTALL LOCK WASHER AND LOCK NUT

(a) Install a new lock washer and the lock nut.

INSTALL LOCK WASHER AND LOCK NUT

(b) Using SST, torque the lock nut.

SST 09607-60020

Torque: 64 N·m

(c) Check that the axle hub rotates smoothly and there is no looseness on the bearing.

INSTALL LOCK WASHER AND LOCK NUT

(d) Using a spring tension gauge, check the preload.

Preload (at starting): 42 - 67 N (4.3 - 6.8 kgf, 9.5 - 15.0 lbf)

HINT: Make sure to check preload in the direction of rotation.

If the preload is not within the specified value, adjust it again with the adjusting nut.

(e) Secure the lock nut by bending one of the lock washer teeth inward and the other lock washer teeth outward.

4. INSTALL FLANGE

(a) Place a new gasket in position on the axle hub. (b) Install the flange to the axle hub.

(c) Install the 6 cone washers, washers and new nuts.

Torque: 33 N·m

INSTALL FLANGE

(d) Pull out the drive shaft to the outside of the vehicle and select the snap ring which ensures the clearance between the tip of the flange and the snap ring is less than 0.2 mm (0.008 in.).

Snap ring thickness:

INSTALL FLANGE
(e) Using a snap ring expander, install a new snap ring to the drive shaft.

(f) Install a new grease cap to the flange.

5. INSTALL BRAKE CALIPER

(a) Install the brake caliper, washers and 2 bolts.

Torque: 123 N·m

(b) Install the flexible hose and bolt to the steering knuckle.

Torque: 28 N·m

6. INSTALL FRONT WHEEL

Torque: 131 N·m

7. CHECK ABS SPEED SENSOR SIGNAL ( DI-505 )

Test yourself

A quick Toyota Land Cruiser quiz: every answer comes with an explanation and a link to the manual page.