Toyota RAV4 Quiz
2Az-fe engine mechanical

Intake air temperature circuit malfunction

In this manual: 2Az-fe engine mechanical
Introduction — 37Interior — 12Exterior — 432Az-fe engine mechanical — 1552Az-fe ignition — 182Az-fe charging — 232Az-fe emission control — 82az-fe exhaust — 32Az-fe fuel — 72Az-fe lubrication — 4Brake — 17Brake control — 63U140f automatic transaxle — 59Instrument panel — 8Suspension — 18Drive shaft — 23Axle — 6Tire and wheel — 30Air conditioning — 93Lighting — 45Cruise control — 21Differential — 12Door lock — 31Engine immobiliser — 21Horn — 5Can communication — 27Mirror — 5Parking brake — 5Power steering — 27Propeller shaft — 3Seat — 29Seat belt — 27Sliding roof — 25Steering column — 6Wiper and washer — 11Supplemental restraint system — 95Other system — 5Maintenance — 14
38steps
~228min
4/5difficulty
Done 0 of 38
Toyota RAV4. Intake air temperature circuit malfunction

Description
Toyota RAV4. Description

The intake air temperature (iat) sensor, mounted on the mass air flow (maf) meter, monitors the iat.

The iat sensor has a built-in thermistor with a resistance that varies according to the temperature of the intake air. When the iat is low, the resistance of the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are transmitted to the ecm as voltage changes (see fig. 1).

The iat sensor is powered by a 5 v supply from the tha terminal of the ecm, via resistor r.

Resistor r and the iat sensor are connected in series. When the resistance value of the iat sensor changes, according to changes in the iat, the voltage at terminal tha also varies. Based on this signal, the ecm increases the fuel injection volume when the engine is cold to improve drivability.

Hint: when any of dtcs p0110, p0112 and p0113 are set, the ecm enters fail-safe mode. During fail-safe mode, the iat is estimated to be 20°c (68°f) by the ecm. Fail-safe mode continues until a pass condition is detected.

Toyota RAV4. Intake air temperature circuit malfunction

Hint:

When any of these dtcs are set, check the iat by selecting the following menu items on the intelligent tester: diagnosis / enhanced obd ii / data list / primary / intake air.

Toyota RAV4. Intake air temperature circuit malfunction

Monitor description

The ecm monitors the sensor voltage and uses this value to calculate the iat. When the sensor output voltage deviates from the normal operating range, the ecm interprets this as a malfunction in the iat sensor and sets a dtc.

Example: if the sensor output voltage is more than 4.91 V for 0.5 Seconds or more, the ecm determines that there is an open in the iat sensor circuit, and sets dtc p0113. Conversely, if the output voltage is less than 0.18 V for 0.5 Seconds or more, the ecm determines that there is a short in the sensor circuit, and sets dtc p0112.

If the malfunction is not repaired successfully, a dtc is set 0.5 Seconds after the engine is next started.

Monitor strategy
Toyota RAV4. Monitor strategy

Typical enabling conditions
Toyota RAV4. Typical enabling conditions

Typical malfunction thresholds
Toyota RAV4. Typical malfunction thresholds

Component operating range
Toyota RAV4. Component operating range

Wiring diagram
Toyota RAV4. Wiring diagram

Inspection procedure Hint:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

  1. Read output dtc
  2. Connect the intelligent tester to the dlc3.
  3. Turn the ignition switch on and turn the intelligent tester on.
  4. Select the following menu items: diagnosis / enhanced obd ii / dtc info / current codes.
  5. Read dtcs.
Result


  1. Read value using intelligent tester (intake air temperature)
  2. Connect the intelligent tester to the dlc3.
  3. Turn the ignition switch on.
  4. Turn the tester on.
  5. Select the following menu items: diagnosis / enhanced obd ii / data list / primary / intake air.
  6. Read the value displayed on the tester.
Standard: same as actual intake air temperature (iat). Result
Hint:
  • If there is an open circuit, the intelligent tester indicates -40°c (-40°f).
  • If there is a short circuit, the intelligent tester indicates 140°c (284°f) or higher.


  1. Read value using intelligent tester (check for open in wire harness)
  2. Disconnect the b1 mass air flow (maf) meter connector.
  3. Connect terminals tha and e2 of the maf meter wire harness side connector.
  4. Connect the intelligent tester to the dlc3.
  5. Turn the ignition switch on.
  6. Turn the tester on.
  7. Select the following menu items: diagnosis / enhanced obd ii / data list / primary / intake air.
  8. Read the value displayed on the tester.
Standard value: 140°c (284°f) or higher
  1. Reconnect the maf meter connector.


  1. Check harness and connector (mass air flow meter - ecm)
  2. Disconnect the b1 maf meter connector.
  3. Disconnect the b30 ecm connector.
  4. Measure the resistance.
Standard resistance
  1. Reconnect the maf meter connector.
  2. Reconnect the ecm connector.

Confirm good connection to ecm. If ok, replace ecm
  1. Read value using intelligent tester (check for short in wire harness)
  2. Disconnect the b1 maf meter connector.
  3. Connect the intelligent tester to the dlc3.
  4. Turn the ignition switch on.
  5. Turn the tester on.
  6. Select the following menu items: diagnosis / enhanced obd ii / data list / primary / intake air.
  7. Read the value displayed on the tester.
Standard value: -40°c (-40°f)
  1. Reconnect the maf meter connector.


  1. Check harness and connector (mass air flow meter - ecm)
  2. Disconnect the b1 maf meter connector.
  3. Disconnect the b30 ecm connector.
  4. Measure the resistance.
Standard resistance
  1. Reconnect the maf meter connector.
  2. Reconnect the ecm connector.

Test yourself

A quick Toyota RAV4 quiz: every answer comes with an explanation and a link to the manual page.