Engine, Hybrid System
Transfer Shift Motor Limit Switch Circuit (P17AC)
Done 0 of 8
DESCRIPTION
This DTC is detected when a malfunction is detected in the limit switch circuit, which detects the position of the transfer shift motor.
WIRING DIAGRAM
Refer to DTC P17AB (See page ).
PROCEDURE
CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - TRANSFER SHIFT ACTUATOR ASSEMBLY)
(a) Disconnect the A26 4 wheel drive control ECU connector.
(b) Disconnect the D68 transfer shift actuator assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
A26-18 (TL1) - D68-1 (TL1) |
Always |
Below 1 Ω |
A26-20 (TL2) - D68-2 (TL2) |
Always |
Below 1 Ω |
A26-26 (TL3) - D68-3 (TL3) |
Always |
Below 1 Ω |
A26-24 (TL4) - D68-4 (TL4) |
Always |
Below 1 Ω |
A26-22 (GTL) - D68-5 (GTL) |
Always |
Below 1 Ω |
A26-18 (TL1) or D68-1 (TL1) - Body ground |
Always |
10 kΩ or higher |
A26-20 (TL2) or D68-2 (TL2) - Body ground |
Always |
10 kΩ or higher |
A26-26 (TL3) or D68-3 (TL3) - Body ground |
Always |
10 kΩ or higher |
A26-24 (TL4) or D68-4 (TL4) - Body ground |
Always |
10 kΩ or higher |
A26-18 (TL1) - D68-2 (TL2), D68-3 (TL3), D68-4 (TL4) and D68-5 (GTL) |
Always |
10 kΩ or higher |
A26-20 (TL2) - D68-1 (TL1), D68-3 (TL3), D68-4 (TL4) and D68-5 (GTL) |
Always |
10 kΩ or higher |
A26-26 (TL3) - D68-1 (TL1), D68-2 (TL2), D68-4 (TL4) and D68-5 (GTL) |
Always |
10 kΩ or higher |
A26-24 (TL4) - D68-1 (TL1), D68-2 (TL2), D68-3 (TL3) and D68-5 (GTL) |
Always |
10 kΩ or higher |
| NG |
 |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
| OK |
 |
|
CHECK 4 WHEEL DRIVE CONTROL ECU (ECU OUTPUT VOLTAGE)
(a) Disconnect the transfer shift actuator assembly connector.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Switch Condition | Specified Condition |
D68-1 (TL1) - Body ground |
Ignition switch ON |
4 to 6 V |
D68-2 (TL2) - Body ground |
Ignition switch ON |
4 to 6 V |
D68-3 (TL3) - Body ground |
Ignition switch ON |
4 to 6 V |
D68-4 (TL4) - Body ground |
Ignition switch ON |
4 to 6 V |
Text in Illustration
*a |
Front view of wire harness connector
(to Transfer Shift Actuator Assembly) |
| OK |
 |
REPLACE TRANSFER SHIFT ACTUATOR ASSEMBLY |
| NG |
 |
REPLACE 4 WHEEL DRIVE CONTROL ECU |
|
Was this page helpful?