Bonnet, flaps, cab, central locking. Bonnet

In this manual: Bonnet, flaps, cab, central locking. Bonnet
Technical data. Panel gaps - front — 1Body front. Lock carrier — 1Body front. Wings — 1Body front. Bulkhead — 1Bonnet, flaps, cab, central locking. Bonnet — 1Bonnet, flaps, cab, central locking. Rear lid — 1Bonnet, flaps, cab, central locking. Charging flap unit — 1Front door, central locking. Door — 1Front door, central locking. Door components — 1Front door, central locking. Central locking — 1Rear door,sliding door,wing doors,central locking. Door — 1Rear door,sliding door,wing doors,central locking. Door components — 1Sliding roof. Sliding sunroof — 1Bumper. Bumper, front — 1Bumper. Bumper, rear — 1Glazing & window mechanism. Repair notes — 1Glazing & window mechanism. Windscreen — 1Glazing & window mechanism. Rear windscreen — 1Glazing & window mechanism. Side windows — 1Glazing & window mechanism. Door windows — 1Exterior equipment. Spoiler — 1Exterior equipment. Mouldings, trims, extensions — 1Exterior equipment. Underbody cladding — 1Exterior equipment. Roof moulding and roof railing — 1Exterior equipment. Exterior mirror — 1Exterior equipment. Wheel housing liner — 1Exterior equipment. Lettering and emblems — 1Exterior equipment. Bicycle carrier — 1Exterior equipment. Trim film and protective film — 1Interior equipment. Compartments & covers — 1Interior equipment. Equipment — 1Interior equipment. Centre console — 1Interior equipment. Front centre armrest — 1Interior equipment. Interior mirror — 1Passenger protection. Seat belts — 1Passenger protection. Child seat anchors — 1Passenger protection. Airbag system — 1Passenger protection. Airbag control unit — 1Passenger protection. Front airbag, driver side — 1Passenger protection. Front passenger airbag — 1Passenger protection. Side airbags — 1Passenger protection. Curtain airbags — 1Passenger protection. Airbag crash sensors — 1Passenger protection. Seat occupied recognition — 1Trim, noise insulation. Front door trims — 1Trim, noise insulation. Rear door trims — 1Trim, noise insulation. Dash panel — 1Trim, noise insulation. Central tube for dash panel — 1Trim, noise insulation. Interior trims — 1Trim, noise insulation. Roof trims — 1Trim, noise insulation. Luggage compartment trims — 1Seat frames. Overview of seat variants — 1Seat frames. Front seats — 1Seat frames. Rear seats — 1Seat padding, covers. Front seat covers and padding — 1Seat padding, covers. Rear seat covers and padding — 1Vehicle-specific paintwork information. Explanation of symbols — 1Vehicle-specific paintwork information. Paintwork structure — 1Vehicle-specific paintwork information. Areas exposed to stone chipping — 1Vehicle-specific paintwork information. Masked sectors — 1Vehicle-specific paintwork information. Seam sealing — 1Vehicle-specific paintwork information. Underseal — 1Vehicle-specific paintwork information. Cavity sealing — 1Vehicle-specific paintwork information. Contrasting colours — 1Vehicle-specific paintwork information. Paintwork repair — 1Technical data. Acoustic considerations during vehicle development — 1Technical data. General procedure for identifying noises — 1Technical data. Volkswagen equipment for localising noises — 1Technical data. Borescope VAS 6748A — 1Technical data. Causes — 1Technical data. Locating water ingress — 1Technical data. Attachments — 1Technical data. Vehicle identification data — 1Technical data. Safety information — 1Technical data. Body parts and materials — 1Technical data. Alignment jig — 1Body front. Longitudinal member cross panel — 1Body front. Longitudinal member — 1Body front. Front wheel housing — 1Body centre, roof, frame. Roof — 1Body centre, roof, frame. A-pillar — 1Body centre, roof, frame. B-pillar — 1Body centre, roof, frame. Side member — 1Body, rear. Rear cross member — 1Body, rear. Rear cross panel — 1Body, rear. Luggage compartment floor — 1Body, rear. Rear longitudinal member — 1Body, rear. Side panel — 1Body, rear. Rear wheel housing — 1General information, Body. Basic information on body repairs — 1General information, Body. Explanation of symbols — 1General information, Body. Overview of materials used — 1General information, Body. Joining and separating techniques — 1General information, Body. Surface repair — 1General information, Body. Corrosion protection — 1General information, Body. Noise insulation — 1General information, Body. Plastic repair — 1General information, Body. Welding plastic attachments — 1General information, Body. General notes – windows — 1General information, Body. Glass repair — 1General information, Body. Use of adhesives — 1General information, Body. Self-adhesive components — 1General information, Body. Noises — 1General information, Body. Preparing for disposal — 1General information, Body. Leaks — 1General information, paint. Safety information — 1General information, paint. General information — 1Genuine products. Filler — 1Genuine products. Priming metal — 1Genuine products. Priming plastic materials — 1Genuine products. Surfacer — 1Genuine products. 2-pack top coats — 1Repair painting work. Paint finish – decorative strips and films — 1Repair painting work. Tips and tricks — 1Air conditioner. Overview of fitting locations — 1Air conditioner. Refrigerant circuit — 1Air conditioner. Valve unit of heat pump — 1Air conditioner. Air conditioner compressor — 1Air conditioner. Control motors — 1Air conditioner. Front heater and air conditioning unit — 1Air conditioner. Air duct — 1Air conditioner. Coolant circuit — 1Air conditioner. Other controlling and regulating components — 1Air conditioner. Air quality improvement system — 11-speed gearbox 0MH, rear, EQ310. Technical data — 11-speed gearbox 0MH, rear, EQ310. Gearbox mechanics,operation, construction,diff — 11-speed gearbox 0MH, rear, EQ310. Final drive, differential, differential lock — 1General information. High voltage — 1Electric drive EIP220, EIA200, EIA210. Technical data — 1Electric drive EIP220, EIA200, EIA210. Engine assy,cylinder block,crankcase — 1Electric drive EIP220, EIA200, EIA210. Engine cooling — 1Electric drive. High-voltage components, charging unit and voltage converter — 1Electric drive. Warning stickers — 1Electric drive. High-voltage battery unit, edge of upper part of battery housing without wax — 1Electric drive. High-voltage battery unit, edge of upper part of battery housing with wax — 1Electric drive. Power and control electronics for electric drive — 1Electric drive. Electric drive motor — 1Electric drive. Motor control unit — 1Electric drive. De-energising high-voltage system — 1Electric drive. Re-energise high-voltage system — 1Electric drive. Potential equalisation lines — 1Electric drive. Charging socket, with charging cable — 1Electric drive. Charging socket, with separate charging cable — 1Electric drive. Charging unit for high-voltage battery — 1Electric drive. Charging unit for high-voltage battery, with integrated voltage converter — 1Electric drive. Vehicle noise & engine sound — 1Electric drive. Accelerator pedal — 1Electric drive. Voltage converter — 1Electric drive. High-voltage cables, all-wheel drive — 1Electric drive. High-voltage cables, rear-wheel drive — 1Front suspension, drive shafts. Front axle — 1Front suspension, drive shafts. Subframe — 1Front suspension, drive shafts. Suspension strut, upper suspension link — 1Front suspension, drive shafts. Lower suspension link, swivel joint — 1Front suspension, drive shafts. Wheel bearing — 1Front suspension, drive shafts. Anti-roll bar — 1Rear suspension, drive shaft. Rear axle — 1Rear suspension, drive shaft. Subframe — 1Rear suspension, drive shaft. Anti-roll bar — 1Rear suspension, drive shaft. Suspension link, track rod — 1Rear suspension, drive shaft. Suspension strut, shock absorber, spring — 1Rear suspension, drive shaft. Wheel bearing assembly, trailing arm — 1Rear suspension, drive shaft. Drive shaft — 1Self-levelling air spring system. Electronically controlled damping — 1Self-levelling air spring system. Vehicle level sender — 1Wheels, tyres. axle align. Wheel alignment — 1Wheels, tyres. axle align. Wheels, tyres — 1Steering. Steering wheel — 1Steering. Steering column — 1Steering. Steering rack — 1Brake system. Technical data — 1ABS, ADR, TCS, EDL, ESP. Overview of fitting locations — 1ABS, ADR, TCS, EDL, ESP. Control unit and hydraulic unit — 1ABS, ADR, TCS, EDL, ESP. Sensors — 1Brake, brake mechanics. Front brake — 1Brake, brake mechanics. Rear brake — 1Brake, brake mechanics. Parking brake — 1Brake, brake mechanics. Brake pedal — 1Brakes, hydraulics, regulator, servo. Brake servo and brake master cylinder — 1Brakes, hydraulics, regulator, servo. Hydraulic system — 1Wheels and Tyres Guide. Wheels, tyres. axle align — 1Wheels, tyres. axle align. Instructions on using the guide — 1Wheels, tyres. axle align. Legislative and technical conditions — 1Wheels, tyres. axle align. Wheel change — 1Wheels, tyres. axle align. Fitting tyre — 1Wheels, tyres. axle align. Wheel bolts — 1Wheels, tyres. axle align. Information on tyres — 1Wheels, tyres. axle align. Handling problems — 1Wheels, tyres. axle align. Evaluating tyres — 1Wheels, tyres. axle align. Tyre wear — 1Starter-current supply-CC. Battery — 1Instruments, GCI. Dash panel insert — 1Instruments, GCI. Horn — 1Windscreen wipewash system. Windscreen wiper system — 1Windscreen wipewash system. Windscreen washer system — 1Windscreen wipewash system. Rear window wiper system — 1Windscreen wipewash system. Rear window washer system — 1Lights, lamps, switches outside. LED headlight — 1Lights, lamps, switches outside. LED matrix headlight — 1Lights, lamps, switches outside. Tail lights — 1Lights, lamps, switches outside. Lights in exterior mirror — 1Lights, lamps, switches outside. Number plate light — 1Lights, lamps, switches outside. Entry and start authorisation system — 1Lights, lamps, switches outside. Steering column switch module — 1Lights, lamps, switches outside. Towing bracket — 1Lights, lamps, switches inside, anti-theft system. Lights — 1Lights, lamps, switches inside, anti-theft system. Controls — 1Lights, lamps, switches inside, anti-theft system. Anti-theft alarm system — 1Lights, lamps, switches inside, anti-theft system. Cigarette lighter, socket — 1Wiring. Relay carriers, fuse holders, electronics boxes — 1Wiring. Control units — 1Infotainment. Componentscontrol units — 1Infotainment. Multifunction steering wheel — 1Driver assist systems. Senders, sensors, control units — 1Driver assist systems. Adaptive cruise control — 1Driver assist systems. Reversing camera system — 1Driver assist systems. Front camera for driver assist systems — 1Driver assist systems. Overhead view camera — 1Electrical system. Starter-current supply-CC — 1Electrical system. Windscreen wipe and wash system — 1Wiring. Wires and lines — 1Wiring. Cleaning contact surfaces — 1
~11min read
0102030405097N·mlb·ft
Tightening torque found on this page
  • Assembly overview – bonnet
  • Assembly overview – Bowden cable
  • Removing and installing bonnet
  • Adjusting bonnet
  • Removing and installing bonnet lock
  • Removing and installing bonnet lock operating lever
  • Removing and installing striker pin
  • Removing and installing hinge
  • Adjusting hinges
  • Adjusting striker pin
  • Setting adjusting buffers
  • Adjusting bonnet lock
  • Removing and installing Bowden cable
  • Removing and installing bonnet stay

Assembly overview – bonnet

Assembly overview – bonnet

1 - Bonnet

❏ → Rep. gr.55; Removing and installing bonnet

❏ → Rep. gr.55; Adjusting bonnet

2 - Striker pin

❏ → Rep. gr.55; Removing and installing striker pin

❏ → Rep. gr.55; Adjusting striker pin

3 - Nut

❏ Qty. 2

❏ 9 N·m

4 - Adjusting buffer

❏ Qty. 2

❏ → Rep. gr.55; Setting adjusting buffer

5 - Hinge

❏ → Rep. gr.55; Removing and installing hinge

❏ → Rep. gr.55; Adjusting hinges

6 - Nut

❏ Qty. 4

❏ 20 N·m

7 - Bolt

❏ Qty. 4

❏ 20 N·m

8 - Bonnet stay

❏ → Rep. gr.55; Removing and installing bonnet stay

9 - Bonnet lock

❏ With bonnet contact switch -F266-

❏ → Rep. gr.55; Removing and installing bonnet lock

❏ → Rep. gr.55; Adjusting bonnet lock

10 - Bolt

❏ Qty. 2

❏ Renew after removing

❏ 12 N·m

Assembly overview – Bowden cable

Assembly overview – Bowden cable

Overview shows left-hand drive vehicle as an example

1 - Bonnet lock operating lever

❏ → Rep. gr.55; Removing and installing bonnet lock operating lever

2 - Bolt

❏ 2 N·m

3 - Mounting bracket

4 - Expansion nut

5 - Bowden cable

❏ From mounting bracket -3- to Bowden cable coupling -7-

❏ → Rep. gr.55; Removing and installing Bowden cable

6 - Grommet

7 - Bowden cable coupling

❏ Installation position depends on the model

8 - Electrical connector for bonnet contact switch -F266-

9 - Bowden cable

❏ From Bowden cable coupling -7- to bonnet lock -10-.

❏ → Rep. gr.55; Removing and installing Bowden cable

10 - Bonnet lock

❏ With bonnet contact switch -F266-

❏ → Rep. gr.55; Removing and installing bonnet lock

11 - Bolt

❏ Qty. 2

❏ 12 N·m

Removing and installing bonnet

Removing and installing bonnet

Removing

– Remove spray jets -5- → Electrical system; Rep. gr.92; Window washer system; Removing and installing spray jets.

– Pull out washer fluid hose and electrical wires -4-.

– Loosen nuts -2- of hinges -3-.

Important

● The aid of an additional person is required for the subsequent work steps.

– Unhook bonnet stay -6- from bonnet -1-.

– Unscrew nuts -2-.

– Remove bonnet -1-.

Installing

Install in reverse order of removal, observing the following:

NOTICE

Risk of damage to electrical wire if not installed straight.

– Do not kink electrical wire and route in a curve.

– → Rep. gr.55; Adjust bonnet.

Tightening torques

♦ → Rep. gr.55; Assembly overview – bonnet

Adjusting bonnet

Adjusting bonnet

Special tools and workshop equipment required

♦ Setting gauge -3371-

Important

● The vehicle must be standing on its wheels and on a level surface to ensure proper adjustment of the bonnet.

● Bonnet must engage in bonnet lock without excessive force.

● Striker pin must enter bonnet lock in centre.

The bonnet is correctly adjusted when the following applies in closed condition:

♦ Gaps are even

♦ Contours are flush with each other

♦ Bonnet does not protrude too far inwards or outwards

– Adjust adjusting buffers → Rep. gr.55; Adjusting adjusting buffers.

– Adjust hinges → Rep. gr.55; Adjusting hinges.

– Adjust bonnet lock → Rep. gr.55; Adjusting bonnet lock.

– Adjust striker pin → Rep. gr.55; Adjusting striker pin.

– Check gaps with setting gauge -3371-, observing → Rep. gr.00; front gaps while doing so.

Removing and installing bonnet lock

Removing and installing bonnet lock

Removal and installation are described for a left-hand drive vehicle as an example.

Removing

– Remove lock carrier → Rep. gr.50; Removing and installing lock carrier.

– Unclip Bowden cable -2- and electrical wire -5- from retainers -7-.

– Unscrew bolts -3-.

– Remove bonnet lock -1- in direction of -arrow A- from lock carrier -6-.

– Unclip electrical wire -5- from bonnet lock.

– Slightly pull retainer -4- in direction of -arrow B- off bonnet lock -1-, and detach Bowden cable -2- in direction of -arrow C-.

Installing

Install in reverse order of removal, observing the following:

Tightening torques

♦ → Rep. gr.55; Assembly overview – Bowden cable

Removing and installing bonnet lock operating lever

Removing and installing bonnet lock operating lever

Removal and installation are described for a left-hand drive vehicle as an example.

Bonnet lock operating lever is referred to hereafter as operating lever.

Removing

– Pull operating lever -1-, and hold it in this position.

– Using commercially available screwdriver, pull retaining clip -2- in direction of -arrow A- out of operating lever -1-.

– Detach operating lever -1- from mounting bracket -3- in direction of -arrow B-.

Installing

Install in reverse order.

Removing and installing striker pin

Removing and installing striker pin

Removing

– Unscrew nuts -2-.

– Remove striker pin -1- from bonnet.

Installing

Install in reverse order of removal, observing the following:

– → Rep. gr.55; Adjust striker pin.

Tightening torques

♦ → Rep. gr.55; Assembly overview – bonnet

Removing and installing hinge

Removing and installing hinge

Removal and installation are described for the right vehicle side as an example.

Removing

– Remove bonnet → Rep. gr.55; Removing and installing bonnet.

– Unscrew bolts -2-.

– Pull off hinge -1-.

Installing

Install in reverse order of removal, observing the following:

New hinge with cable holder

– Install cable holder -1- in hinge.

All vehicles (continued)

– Apply corrosion protection measures to bolts.

Observe instructions in the paintwork manual → Corrosion protection on body, attachments and welded parts.

– → Rep. gr.55; Adjust bonnet.

Tightening torques

♦ → Rep. gr.55; Assembly overview – bonnet

Adjusting hinges

Adjusting hinges

Special tools and workshop equipment required

♦ Setting gauge -3371-

The procedure is described for the left side of vehicle as an example.

Note

The bonnet can be centred between the wings in direction of -arrow C- and in direction of -arrow D-.

– Loosen nuts -2- to adjust hinge -1- in direction of -arrow C- or in direction of -arrow D-.

Note

The height of the bonnet relative to the wings can be adjusted in direction of -arrow B-.

Note

The bonnet can be adjusted relative to the bumper cover in direction of -arrow A-.

– Loosen bolts -3- to adjust hinge -1- in direction of -arrow A- or in direction of -arrow B-.

– Verify gaps using setting gauge -3371-. Observe → Rep. gr.00; Gaps - front when doing this.

– Apply corrosion protection measures to hinges -1-, nuts -2- and bolts -3- → Corrosion protection on body, attachments and welded parts.

– → Rep. gr.55; Adjust adjusting buffers.

Tightening torques

♦ → Rep. gr.55; Assembly overview – bonnet

Adjusting striker pin

Adjusting striker pin

– Adjust striker pin in direction of -arrow A- to align it centrally relative to bonnet lock.

– Loosen nuts -2- to adjust striker pin -1- in direction of -arrow A-.

Important

● Do not use striker pin to align bonnet centrally in direction of -arrow A-.

● Striker pin must enter bonnet lock in centre.

Tightening torques

♦ → Rep. gr.55; Assembly overview – bonnet

Setting adjusting buffers

Setting adjusting buffers

Adjusting buffers stabilise the bonnet and provide shock absorption.

– Adjust bonnet lock → Rep. gr.55; Removing and installing bonnet lock.

– Adjust striker pin → Rep. gr.55; Adjusting striker pin.

Note

Adjusting buffers offer stability and protect against impact. Applying too much pressure on the rubber buffer will result in a malfunction.

– Turn adjusting buffer -1- in direction of -arrow A- or -arrow B-.

Important

● When bonnet is closed, adjusting buffers -1- must have light contact with stop buffers.

Adjusting bonnet lock

Adjusting bonnet lock

Special tools and workshop equipment required

♦ Setting gauge -3371-

Important

● Do not use bonnet lock to align bonnet centrally in direction of -arrow A-.

● Striker pin must enter bonnet lock in centre. → Rep. gr.55; Adjusting striker pin

Note

The bonnet can be adjusted relative to the front bumper cover in direction of -arrow B-.

– Loosen bolts -2- to adjust bonnet lock -1- in direction of -arrow A- or direction of -arrow B-.

– Verify gaps using setting gauge -3371-. Observe → Rep. gr.00; Gaps - front when doing this.

– Apply corrosion protection measures to bolts -2- → Corrosion protection on body, attachments and welded parts.

Tightening torques

♦ → Rep. gr.55; Assembly overview – bonnet

Removing and installing Bowden cable

Removing and installing Bowden cable

Removal and installation are described for a left-hand drive vehicle as an example.

Removing

– Remove lower A-pillar trim → General body repairs, interior; Rep. gr.70; Trims, interior; Removing and installing lower A-pillar trim.

– Remove footwell cover on driver side → General body repairs, interior; Rep. gr.68; Compartments/covers; Removing and installing footwell cover on driver side.

– Remove front wheel housing liner on driver side → Rep. gr.66; Removing and installing front wheel housing liner.

– Remove wiper motor -V- → Electrical system; Rep. gr.92; Windscreen wiper system; Removing and installing wiper motor V.

– Detach Bowden cable -1- in direction of -arrow A- from mounting bracket -2-.

– Pull Bowden cable coupling -1- in direction of -arrow A- off carrier -3-.

– Pretension Bowden cable -2- in direction of -arrow B-, and hold it in this position.

– Open cap -2- of Bowden cable coupling -1- in direction of -arrow A-.

– Remove Bowden cable -3- in direction of -arrow B- from Bowden cable coupling -1-.

– Pull Bowden cable -1- together with grommet -2- in direction of -arrow A- off body, and remove it.

Installing

– Guide Bowden cable -1- with grommet -2- in direction of -arrow A- through opening in body -3- towards vehicle interior.

– Push grommet -2- into opening in body -3-.

– Make sure that grommet -2- is seated correctly.

NOTICE

Risk of malfunction of the bonnet lock due to incorrect position of the Bowden cable in the Bowden cable coupling.

If the Bowden cable is installed in the wrong position, the bonnet can no longer be opened.

– Make sure that the Bowden cable is correctly positioned in the Bowden cable coupling.

– Always carry out a functional check before closing the bonnet.

– Attach Bowden cable -3- in direction of -arrow A- to Bowden cable coupling -1-.

– Use cap -2- of Bowden cable coupling -1- to fix Bowden cable -3- in position, but do not close cap -2-.

– Pretension Bowden cable -3- in direction of -arrow B-, and hold it in this position.

– Close cap -2- in direction of -arrow C-.

– Relieve tension from Bowden cable -1- in direction of -arrow A-.

– Secure Bowden cable coupling -2- on carrier in direction of -arrow B-.

– Attach Bowden cable -1- in direction of -arrow A- to mounting bracket -2-.

Continue installation in reverse sequence of removal, observing the following:

– Perform functional check.

– Close bonnet.

Removing and installing bonnet stay

Removing and installing bonnet stay

Special tools and workshop equipment required

♦ Bonnet support -VAS 501 003-

Removal and installation are described for vehicles with bonnet stay on right as an example.

Bonnet stay mounting design is model-specific.

Removing

NOTICE

Risk of damage to adjacent components caused by a loose bonnet.

Risk of paint damage.

– Brace the bonnet open.

– Support bonnet using bonnet support -VAS 501 003-.

– Pull bonnet stay -1- out of clip -2-.

– Swivel bonnet stay -1- out of mounting on lock carrier.

– Remove bonnet stay -1- in direction of -arrow B-.

Installing

Install in reverse order.