Genuine products. Filler

In this manual: Genuine products. Filler
Technical data. Panel gaps - front — 1Body front. Lock carrier — 1Body front. Wings — 1Body front. Bulkhead — 1Bonnet, flaps, cab, central locking. Bonnet — 1Bonnet, flaps, cab, central locking. Rear lid — 1Bonnet, flaps, cab, central locking. Charging flap unit — 1Front door, central locking. Door — 1Front door, central locking. Door components — 1Front door, central locking. Central locking — 1Rear door,sliding door,wing doors,central locking. Door — 1Rear door,sliding door,wing doors,central locking. Door components — 1Sliding roof. Sliding sunroof — 1Bumper. Bumper, front — 1Bumper. Bumper, rear — 1Glazing & window mechanism. Repair notes — 1Glazing & window mechanism. Windscreen — 1Glazing & window mechanism. Rear windscreen — 1Glazing & window mechanism. Side windows — 1Glazing & window mechanism. Door windows — 1Exterior equipment. Spoiler — 1Exterior equipment. Mouldings, trims, extensions — 1Exterior equipment. Underbody cladding — 1Exterior equipment. Roof moulding and roof railing — 1Exterior equipment. Exterior mirror — 1Exterior equipment. Wheel housing liner — 1Exterior equipment. Lettering and emblems — 1Exterior equipment. Bicycle carrier — 1Exterior equipment. Trim film and protective film — 1Interior equipment. Compartments & covers — 1Interior equipment. Equipment — 1Interior equipment. Centre console — 1Interior equipment. Front centre armrest — 1Interior equipment. Interior mirror — 1Passenger protection. Seat belts — 1Passenger protection. Child seat anchors — 1Passenger protection. Airbag system — 1Passenger protection. Airbag control unit — 1Passenger protection. Front airbag, driver side — 1Passenger protection. Front passenger airbag — 1Passenger protection. Side airbags — 1Passenger protection. Curtain airbags — 1Passenger protection. Airbag crash sensors — 1Passenger protection. Seat occupied recognition — 1Trim, noise insulation. Front door trims — 1Trim, noise insulation. Rear door trims — 1Trim, noise insulation. Dash panel — 1Trim, noise insulation. Central tube for dash panel — 1Trim, noise insulation. Interior trims — 1Trim, noise insulation. Roof trims — 1Trim, noise insulation. Luggage compartment trims — 1Seat frames. Overview of seat variants — 1Seat frames. Front seats — 1Seat frames. Rear seats — 1Seat padding, covers. Front seat covers and padding — 1Seat padding, covers. Rear seat covers and padding — 1Vehicle-specific paintwork information. Explanation of symbols — 1Vehicle-specific paintwork information. Paintwork structure — 1Vehicle-specific paintwork information. Areas exposed to stone chipping — 1Vehicle-specific paintwork information. Masked sectors — 1Vehicle-specific paintwork information. Seam sealing — 1Vehicle-specific paintwork information. Underseal — 1Vehicle-specific paintwork information. Cavity sealing — 1Vehicle-specific paintwork information. Contrasting colours — 1Vehicle-specific paintwork information. Paintwork repair — 1Technical data. Acoustic considerations during vehicle development — 1Technical data. General procedure for identifying noises — 1Technical data. Volkswagen equipment for localising noises — 1Technical data. Borescope VAS 6748A — 1Technical data. Causes — 1Technical data. Locating water ingress — 1Technical data. Attachments — 1Technical data. Vehicle identification data — 1Technical data. Safety information — 1Technical data. Body parts and materials — 1Technical data. Alignment jig — 1Body front. Longitudinal member cross panel — 1Body front. Longitudinal member — 1Body front. Front wheel housing — 1Body centre, roof, frame. Roof — 1Body centre, roof, frame. A-pillar — 1Body centre, roof, frame. B-pillar — 1Body centre, roof, frame. Side member — 1Body, rear. Rear cross member — 1Body, rear. Rear cross panel — 1Body, rear. Luggage compartment floor — 1Body, rear. Rear longitudinal member — 1Body, rear. Side panel — 1Body, rear. Rear wheel housing — 1General information, Body. Basic information on body repairs — 1General information, Body. Explanation of symbols — 1General information, Body. Overview of materials used — 1General information, Body. Joining and separating techniques — 1General information, Body. Surface repair — 1General information, Body. Corrosion protection — 1General information, Body. Noise insulation — 1General information, Body. Plastic repair — 1General information, Body. Welding plastic attachments — 1General information, Body. General notes – windows — 1General information, Body. Glass repair — 1General information, Body. Use of adhesives — 1General information, Body. Self-adhesive components — 1General information, Body. Noises — 1General information, Body. Preparing for disposal — 1General information, Body. Leaks — 1General information, paint. Safety information — 1General information, paint. General information — 1Genuine products. Filler — 1Genuine products. Priming metal — 1Genuine products. Priming plastic materials — 1Genuine products. Surfacer — 1Genuine products. 2-pack top coats — 1Repair painting work. Paint finish – decorative strips and films — 1Repair painting work. Tips and tricks — 1Air conditioner. Overview of fitting locations — 1Air conditioner. Refrigerant circuit — 1Air conditioner. Valve unit of heat pump — 1Air conditioner. Air conditioner compressor — 1Air conditioner. Control motors — 1Air conditioner. Front heater and air conditioning unit — 1Air conditioner. Air duct — 1Air conditioner. Coolant circuit — 1Air conditioner. Other controlling and regulating components — 1Air conditioner. Air quality improvement system — 11-speed gearbox 0MH, rear, EQ310. Technical data — 11-speed gearbox 0MH, rear, EQ310. Gearbox mechanics,operation, construction,diff — 11-speed gearbox 0MH, rear, EQ310. Final drive, differential, differential lock — 1General information. High voltage — 1Electric drive EIP220, EIA200, EIA210. Technical data — 1Electric drive EIP220, EIA200, EIA210. Engine assy,cylinder block,crankcase — 1Electric drive EIP220, EIA200, EIA210. Engine cooling — 1Electric drive. High-voltage components, charging unit and voltage converter — 1Electric drive. Warning stickers — 1Electric drive. High-voltage battery unit, edge of upper part of battery housing without wax — 1Electric drive. High-voltage battery unit, edge of upper part of battery housing with wax — 1Electric drive. Power and control electronics for electric drive — 1Electric drive. Electric drive motor — 1Electric drive. Motor control unit — 1Electric drive. De-energising high-voltage system — 1Electric drive. Re-energise high-voltage system — 1Electric drive. Potential equalisation lines — 1Electric drive. Charging socket, with charging cable — 1Electric drive. Charging socket, with separate charging cable — 1Electric drive. Charging unit for high-voltage battery — 1Electric drive. Charging unit for high-voltage battery, with integrated voltage converter — 1Electric drive. Vehicle noise & engine sound — 1Electric drive. Accelerator pedal — 1Electric drive. Voltage converter — 1Electric drive. High-voltage cables, all-wheel drive — 1Electric drive. High-voltage cables, rear-wheel drive — 1Front suspension, drive shafts. Front axle — 1Front suspension, drive shafts. Subframe — 1Front suspension, drive shafts. Suspension strut, upper suspension link — 1Front suspension, drive shafts. Lower suspension link, swivel joint — 1Front suspension, drive shafts. Wheel bearing — 1Front suspension, drive shafts. Anti-roll bar — 1Rear suspension, drive shaft. Rear axle — 1Rear suspension, drive shaft. Subframe — 1Rear suspension, drive shaft. Anti-roll bar — 1Rear suspension, drive shaft. Suspension link, track rod — 1Rear suspension, drive shaft. Suspension strut, shock absorber, spring — 1Rear suspension, drive shaft. Wheel bearing assembly, trailing arm — 1Rear suspension, drive shaft. Drive shaft — 1Self-levelling air spring system. Electronically controlled damping — 1Self-levelling air spring system. Vehicle level sender — 1Wheels, tyres. axle align. Wheel alignment — 1Wheels, tyres. axle align. Wheels, tyres — 1Steering. Steering wheel — 1Steering. Steering column — 1Steering. Steering rack — 1Brake system. Technical data — 1ABS, ADR, TCS, EDL, ESP. Overview of fitting locations — 1ABS, ADR, TCS, EDL, ESP. Control unit and hydraulic unit — 1ABS, ADR, TCS, EDL, ESP. Sensors — 1Brake, brake mechanics. Front brake — 1Brake, brake mechanics. Rear brake — 1Brake, brake mechanics. Parking brake — 1Brake, brake mechanics. Brake pedal — 1Brakes, hydraulics, regulator, servo. Brake servo and brake master cylinder — 1Brakes, hydraulics, regulator, servo. Hydraulic system — 1Wheels and Tyres Guide. Wheels, tyres. axle align — 1Wheels, tyres. axle align. Instructions on using the guide — 1Wheels, tyres. axle align. Legislative and technical conditions — 1Wheels, tyres. axle align. Wheel change — 1Wheels, tyres. axle align. Fitting tyre — 1Wheels, tyres. axle align. Wheel bolts — 1Wheels, tyres. axle align. Information on tyres — 1Wheels, tyres. axle align. Handling problems — 1Wheels, tyres. axle align. Evaluating tyres — 1Wheels, tyres. axle align. Tyre wear — 1Starter-current supply-CC. Battery — 1Instruments, GCI. Dash panel insert — 1Instruments, GCI. Horn — 1Windscreen wipewash system. Windscreen wiper system — 1Windscreen wipewash system. Windscreen washer system — 1Windscreen wipewash system. Rear window wiper system — 1Windscreen wipewash system. Rear window washer system — 1Lights, lamps, switches outside. LED headlight — 1Lights, lamps, switches outside. LED matrix headlight — 1Lights, lamps, switches outside. Tail lights — 1Lights, lamps, switches outside. Lights in exterior mirror — 1Lights, lamps, switches outside. Number plate light — 1Lights, lamps, switches outside. Entry and start authorisation system — 1Lights, lamps, switches outside. Steering column switch module — 1Lights, lamps, switches outside. Towing bracket — 1Lights, lamps, switches inside, anti-theft system. Lights — 1Lights, lamps, switches inside, anti-theft system. Controls — 1Lights, lamps, switches inside, anti-theft system. Anti-theft alarm system — 1Lights, lamps, switches inside, anti-theft system. Cigarette lighter, socket — 1Wiring. Relay carriers, fuse holders, electronics boxes — 1Wiring. Control units — 1Infotainment. Componentscontrol units — 1Infotainment. Multifunction steering wheel — 1Driver assist systems. Senders, sensors, control units — 1Driver assist systems. Adaptive cruise control — 1Driver assist systems. Reversing camera system — 1Driver assist systems. Front camera for driver assist systems — 1Driver assist systems. Overhead view camera — 1Electrical system. Starter-current supply-CC — 1Electrical system. Windscreen wipe and wash system — 1Wiring. Wires and lines — 1Wiring. Cleaning contact surfaces — 1
~13min read
  • Electronic Service Information System (ERWIN - ERWIN)
  • 2-pack fine filler
  • 2-pack fine filler, flexible
  • 2-pack spray filler
  • 2-pack IR premium filler
  • 2-pack epoxy resin filler

Electronic Service Information System (ERWIN - ERWIN)

2-pack fine filler

2-pack fine filler

Storage

Guaranteed shelf life is 12 months from date of production.

Can be processed on or before date indicated on label if stored in unopened, original containers at +20 °C.

Storage conditions

♦ Storage temperature +20 °C

♦ +30 °C must not be exceeded

VOC value

Viscosity as suppliedPaste-likeFlash pointFiller above 23°CVOC content: 2004/42/IIB (b) (250) 170The EU limit value for this product (product category IIB.b) in ready-to-spray form is max. 250 g/l of volatile organic compounds. The VOC content of this product in ready-to-spray form is max. 170 g/l.

Product description

2-pack fine filler LSP 784 002 A2 is a very fine, thixotropic polyester filler.

2-pack fine filler is suitable for repairing small defects.

Properties

♦ Fine and non-porous

♦ Easy to apply

♦ Easy to sand

♦ High elasticity for touch-ups over plastic substrates

Suitable substrates

Important

● 2-pack fine filler must not be applied over PVB (acid-curing) surfaces or 1-pack primer (e.g. synthetic resin).

● It is also unsuitable for application over thermoplastic or viscoelastic paint. Only to be applied onto bare metal.

♦ Steel

♦ Aluminium

♦ Glass-reinforced plastic

♦ Old paint and factory paint

♦ Hardened 2-pack surfacers/2-pack primers

♦ Plastic parts primed with 2-pack plastic adhesion surfacer LKF 696 009 A2/2-pack plastic adhesion surfacer LKF 696 040 A2 or primer LVM 823 000 A2

♦ Surfaces prepared with 2-pack polyester filler

Substrate pretreatment

– Thoroughly clean, degrease and roughen substrates.

– For UP-GF (fibreglass) substrate parts, remove residual release agents and lightly sand surface.

– Use suitable cleaning agents for cleaning substrates to make sure that soiling and residue is removed completely.

Application

– Apply filler.

Mixing ratio

– Add 2% by weight of 2-pack hardener LVM 018 000 A1/A2.

Important

● Avoid overdosing hardener, as this can lead to bleeding through, especially with dayglow paints and light metallic colours.

Processing time

Processing time is approx. 3 to 5 minutes at +20 °C ambient temperature.

Reaction temperature must be at least +5 °C.

Drying

Air drying: 15 to 30 minutes at +20 °C ambient temperature.

Infrared drying: short-wave radiant heater, 2 to 3 minutes (at 50% output).

Sanding

– Sand to contour using orbital sander, P180 to 240 grit dry sandpaper and dust collector.

Important

● Temperature resistance to +80 °C.

Recoating

– Paint over with top coat.

♦ 1-pack wash primer LVM 044 007 A2/1-pack wash primer LVM 044 171 A2

♦ 2-pack wash primer LHV 043 000 A2 and 2-pack HS surfacer

♦ 2-pack plastic adhesion surfacer LKF 696 009 A2/2-pack plastic adhesion surfacer LKF 696 040 A2

♦ Primer LVM 823 000 A2 and plasticised 2-pack HS surfacer for plastic parts

2-pack fine filler, flexible

2-pack fine filler, flexible

Data

Mixing ratio2 to 3% by weightAdd hardener2-pack hardener LVM 018 00 A1Pot life2 to 4 minutes at +20°CDrying time (air drying) at +20 °C ambient temperature:20 to 30 minutes Infrared drying (short-wave)3 minutes at 50% outputInfrared drying, medium-wave5 minutesSuitability for sanding:First sandingSecond sandingWetAs fine filler, P180 gritAs fine filler, P320 to P360 gritDryAs stopper, P80 grit
As stopper, P120 gritAs stopper, P120 to P240 grit
As stopper, P280 grit

Product description

2-pack fine filler LSP 787 100 A1 is a flexible 2-pack filler with good filling properties.

The flexible 2-pack fine filler does not shrink and offers excellent adhesion to numerous substrates.

The flexible 2-pack fine filler is especially suitable for plastics.

♦ For repairing plastic outer body skin parts following surface damage involving material abrasion (scratches, holes, incipient tears (yet no severe cracks)

♦ For filling cuprammonium-rayon plastic, which has previously been repaired using plastic repair set D 007 700

♦ To fill over a repair to avoid marking

Properties

♦ Uniform, fine, creamy consistency

♦ Good filling characteristics – no shrinkage

♦ Fast-hardening

♦ Good sanding characteristics

♦ Adheres well to metal and plastic

Suitable substrates

Important

● 2-pack flexible fine filler must not be applied over PVB (acid-curing) surfaces or 1-pack primer (e.g. synthetic resin).

● It is also unsuitable for application over thermoplastic or viscoelastic paint. Only to be applied onto bare metal.

♦ Steel

♦ Galvanised sheet steel

♦ Aluminium

♦ All cleaned and sanded plastics in vehicles

♦ Glass-fibre reinforced plastics, UP-GF

♦ Well-sanded old paint or factory paint

♦ Hardened 2-pack surfacers/2-pack primers

Substrate pretreatment

– Thoroughly clean, degrease and roughen substrates.

– For UP-GF (fibreglass) substrate parts, remove residual release agents and lightly sand surface.

– Use suitable cleaning agents for cleaning substrates to make sure that soiling and residue is removed completely.

Recoating

– Apply fine filler alone.

– Apply 2-pack fine filler LSP 784 002 A2 or rework with 2-pack spray filler ALN 788 007, except on galvanised sheet metal.

– Prime bare metal spots and filler spots with 2-pack wash primer LHV 043 000 A2, then apply 2-pack HS Performance surfacer LVM 014.

– Avoid overdosing hardener, as this can lead to bleeding through, especially with dayglow paints and light metallic colours.

Important

● Minimum reaction temperature at +5 °C.

– Overpaint with top coat.

– Before applying surfacer, sand entire surface using orbital sander, P280 to P500 grit dry sandpaper and dust collector.

2-pack spray filler

2-pack spray filler

Storage

Guaranteed shelf life is 12 months from date of production.

Can be processed on or before date indicated on label if stored in unopened, original containers at +20 °C.

Storage conditions

♦ Storage temperature +20 °C

♦ +30 °C must not be exceeded

VOC value

Viscosity as suppliedThixotropicFlash pointabove 23°CVOC content: 2004/42/IIB (b) (250) 250The EU limit value for this product (product category IIB.b) in ready-to-spray form is max. 250 g/l of volatile organic compounds. The VOC content of this product in ready-to-spray form is max. 250 g/l.

Product description

ALN 788 007 is a 2-pack spray filler used for vehicle repairs.

♦ To even out rough uneven areas

♦ Especially suitable for use on large surfaces

♦ Very good sprayability

♦ Easy to apply and has good vertical stability

♦ Good levelling

Suitable substrates

Important

● 2-pack spray filler ALN 788 007 must not be applied over PVB (acid-curing) surfaces or 1-pack primer (e.g. synthetic resin).

● It is also unsuitable for application over thermoplastic or viscoelastic paint. Only to be applied onto bare metal.

♦ Steel panels cleaned, sanded and primed with 2-pack wash primer LHV 043 000 A2 and then isolated with 2-pack HS Performance surfacer; electroplated or roller galvanized steel panels or aluminium

♦ Hardened, solvent-resistant, well-preserved and sanded old paint or factory paint.

♦ Surfaces treated with 2-pack polyester filler

♦ Cleaned and sanded UP-GF (fibreglass) surfaces, free of release agents

Substrate pretreatment

– Thoroughly clean, degrease and roughen substrates.

– For UP-GF (fibreglass) substrate parts, remove residual release agents and lightly sand surface.

– Use suitable cleaning agents for cleaning substrates to make sure that soiling and residue is removed completely.

Application

– Proceed with method of application: Compliant.

Mixing ratio

– Add 2% by volume of 5-pack hardener LHA 841 000 A2.

Application

Processing time is 20 to 30 minutes at +20 °C ambient temperature.

Minimum reaction temperature is +15℃.

Application viscosity

Application viscosity for +20 °C material temperature.

Spray nozzle and spraying pressure

– Adjust spray nozzle and spraying pressure according to manufacturer’s specifications:

Spray nozzleSpraying pressureCompliant2.0 to 2.5 mm2.0 to 3.0 bar

5 spray passes produce 500 to 600 µm.

Layer thicknesses up to 1000 µm are possible.

Application

– Proceed with method of application: Brushing.

Important

● Brushing involves one continuous brushing pass of spray filler.

Drying

Air drying at +20 °C room temperature:

Can be sanded after 2 hours.

Forced drying:

Flash-off time: 5 to 10 minutes.

Drying time: 30 to 35 minutes at +60 °C to 65 °C material temperature.

Infrared drying:

Flash-off time: at least 5 minutes.

Drying time: 10 to 12 minutes, short-wave radiant heater at 50% output.

Important

● Temperature resistance to +80 °C.

Further steps

– Dry-sand initially using orbital sander, P120 to P220 grit dry sandpaper and dust collector.

– Finish-sand dry using orbital sander, P240 to P360 grit dry sandpaper and dust collector.

Recoating

Rework with:

♦ 2-pack wash primer LHV 043 000 A2, only for exposed metal spots

♦ 2-pack HS surfacer

Top coat as:

♦ Waterborne base coat, 2-pack HS clear coat and 2-pack HS top coat

2-pack IR premium filler

2-pack IR premium filler

Storage

Guaranteed shelf life is 12 months from date of production.

Can be processed on or before date indicated on label if stored in unopened, original containers at +20 °C.

Storage conditions

♦ Storage temperature +20 °C

♦ +30 °C must not be exceeded

VOC value

Viscosity as suppliedPaste-likeFlash pointFiller above 23°CVOC content: 2004/42/IIB (b) (250) 150The EU limit value for this product (product category IIB.b) in ready-to-spray form is max. 250 g/l of volatile organic compounds. The VOC content of this product in ready-to-spray form is max. 150 g/l.

Product description

2-pack IR premium filler LSP 787 220 A1/A2/A3 is a high-grade polyester filler for paint repairs on vehicles.

♦ For all common metallic substrates

♦ Very good adhesion to galvanised substrates

♦ Good sanding properties

♦ Easy to apply and non-porous

♦ Especially suitable for IR drying

Suitable substrates

Important

● 2-pack IR premium filler must not be applied over PVB (acid-curing) surfaces or 1-pack primer (e.g. synthetic resin).

● It is also unsuitable for application over thermoplastic or viscoelastic paint. Only to be applied onto bare metal.

♦ Sheet steel

♦ Galvanised sheet steel

♦ Aluminium

♦ Well-sanded factory paint or old paint

♦ Fully cured, primed two-pack surfacers and two-pack primers

♦ Cleaned and sanded UP-GF (fibreglass) surfaces, free of release agents

Substrate pretreatment

– Thoroughly clean, degrease and roughen substrates.

– For UP-GF (fibreglass) substrate parts, remove residual release agents and lightly sand surface.

– Use suitable cleaning agents for cleaning substrates to make sure that soiling and residue is removed completely.

Application

– Apply filler.

Mixing ratio

– Add 2% by weight of 2-pack hardener LVM 018 000 A1/A2.

– Avoid overdosing hardener, as this can lead to bleeding through, especially with dayglow paints and light metallic colours.

Drying

Processing time is 2 to 4 minutes at +20 °C ambient temperature.

Reaction temperature must be at least +5 °C.

Air drying: 15 to 30 minutes at +20 °C ambient temperature.

Infrared drying with short-wave radiant heater: 2 to 3 minutes at 50% output.

Sanding

– Dry-sand initially using orbital sander, P80 to P220 grit dry sandpaper and dust collector.

– Finish-sand dry using orbital sander, P180 to P240 grit dry sandpaper and dust collector.

Important

● Temperature resistance up to +80 °C

Recoating

– Apply fine filler alone.

– Apply 2-pack fine filler LSP 784 002 A2 or rework with 2-pack spray filler ALN 788 00,7 except on galvanised sheet metal.

– Prime bare metal spots and filler spots with 2-pack wash primer LHV 043 000 A2, then apply 2-pack HS Performance surfacer LVM 014.

2-pack epoxy resin filler

2-pack epoxy resin filler

Storage

Guaranteed shelf life is 12 months from date of production.

May be used until the date stated on the label at the latest if stored in sealed original containers at +20 °C.

Storage conditions

♦ Preferred storage temperature +10 °C to +30 °C.

♦ Store cool and dry

♦ No direct sunlight

Data

Density1.55 g/cm3 Shore D hardness at 20°C84Working temperature+10 °C to +50°CTemperature resistance-40°C to +110 °C

Product description

D 787 400 M2 is a fast-drying 2-pack epoxy filler suitable for use on vehicle bodies.

Mineral- filled filler, no contact corrosion, is specially designed for use as a tin replacement and as a filler for joints and seams.

As it is fast curing and simple to process, it offers a cost-effective solution in the field of body repairs.

Areas of application

♦ Replacement for alluvial tin

♦ Filler for joints

♦ Bonding metal

♦ Carrier system for paint

Properties

♦ Good adhesion on steel, aluminium and zinc

♦ Easy to process (sanding, planing)

♦ Ideal carrier system for paint

♦ Easy to shape and outstanding sag resistance

♦ Fast curing

♦ Dies not sag or run

Substrate pretreatment

– Thoroughly degrease substrates.

– Sand down to bare metal using P60 grit dry sandpaper and dust collector.

– Use suitable cleaning agents for cleaning substrates to make sure that soiling and residue is removed completely.

Application

– Apply filler.

Mixing ratio

2-Pack epoxy filler is delivered in a closed 2-pack cartridge and does not require manual mixing.

– Screw on mixer.

– Do not use the first 5 cm of the extruded 2-pack epoxy filler, as these cannot have been mixed properly.

– Continue pressing out 2-pack epoxy filler until a uniform grey colour is achieved.

Drying

Pot life: 30 minutes at +20 °C ambient temperature

Hardening: 4 hours

Overlaying: 1.5 to 2 hours

Air drying: 4 hours

Infrared drying: drying using short-wave infrared dryer.

Precuring10 minutes at 45°CFull hardening stage 110 minutes at 85°CFull hardening stage 2Allow to cool down at room temperature of 20 °C to 25 °C.

Important

● Make sure that 2-pack epoxy filler does not overheat to temperatures above 100 °C during curing.

● Make sure during hardening that a uniform hardening temperature is maintained at corners and curvatures.

Sanding

After cooling, hardened 2-pack epoxy filler can be sanded using dust extractor and body file or P80-grit dry sandpaper.