Rear suspension, drive shaft. Drive shaft

In this manual: Rear suspension, drive shaft. Drive shaft
Technical data. Panel gaps - front — 1Body front. Lock carrier — 1Body front. Wings — 1Body front. Bulkhead — 1Bonnet, flaps, cab, central locking. Bonnet — 1Bonnet, flaps, cab, central locking. Rear lid — 1Bonnet, flaps, cab, central locking. Charging flap unit — 1Front door, central locking. Door — 1Front door, central locking. Door components — 1Front door, central locking. Central locking — 1Rear door,sliding door,wing doors,central locking. Door — 1Rear door,sliding door,wing doors,central locking. Door components — 1Sliding roof. Sliding sunroof — 1Bumper. Bumper, front — 1Bumper. Bumper, rear — 1Glazing & window mechanism. Repair notes — 1Glazing & window mechanism. Windscreen — 1Glazing & window mechanism. Rear windscreen — 1Glazing & window mechanism. Side windows — 1Glazing & window mechanism. Door windows — 1Exterior equipment. Spoiler — 1Exterior equipment. Mouldings, trims, extensions — 1Exterior equipment. Underbody cladding — 1Exterior equipment. Roof moulding and roof railing — 1Exterior equipment. Exterior mirror — 1Exterior equipment. Wheel housing liner — 1Exterior equipment. Lettering and emblems — 1Exterior equipment. Bicycle carrier — 1Exterior equipment. Trim film and protective film — 1Interior equipment. Compartments & covers — 1Interior equipment. Equipment — 1Interior equipment. Centre console — 1Interior equipment. Front centre armrest — 1Interior equipment. Interior mirror — 1Passenger protection. Seat belts — 1Passenger protection. Child seat anchors — 1Passenger protection. Airbag system — 1Passenger protection. Airbag control unit — 1Passenger protection. Front airbag, driver side — 1Passenger protection. Front passenger airbag — 1Passenger protection. Side airbags — 1Passenger protection. Curtain airbags — 1Passenger protection. Airbag crash sensors — 1Passenger protection. Seat occupied recognition — 1Trim, noise insulation. Front door trims — 1Trim, noise insulation. Rear door trims — 1Trim, noise insulation. Dash panel — 1Trim, noise insulation. Central tube for dash panel — 1Trim, noise insulation. Interior trims — 1Trim, noise insulation. Roof trims — 1Trim, noise insulation. Luggage compartment trims — 1Seat frames. Overview of seat variants — 1Seat frames. Front seats — 1Seat frames. Rear seats — 1Seat padding, covers. Front seat covers and padding — 1Seat padding, covers. Rear seat covers and padding — 1Vehicle-specific paintwork information. Explanation of symbols — 1Vehicle-specific paintwork information. Paintwork structure — 1Vehicle-specific paintwork information. Areas exposed to stone chipping — 1Vehicle-specific paintwork information. Masked sectors — 1Vehicle-specific paintwork information. Seam sealing — 1Vehicle-specific paintwork information. Underseal — 1Vehicle-specific paintwork information. Cavity sealing — 1Vehicle-specific paintwork information. Contrasting colours — 1Vehicle-specific paintwork information. Paintwork repair — 1Technical data. Acoustic considerations during vehicle development — 1Technical data. General procedure for identifying noises — 1Technical data. Volkswagen equipment for localising noises — 1Technical data. Borescope VAS 6748A — 1Technical data. Causes — 1Technical data. Locating water ingress — 1Technical data. Attachments — 1Technical data. Vehicle identification data — 1Technical data. Safety information — 1Technical data. Body parts and materials — 1Technical data. Alignment jig — 1Body front. Longitudinal member cross panel — 1Body front. Longitudinal member — 1Body front. Front wheel housing — 1Body centre, roof, frame. Roof — 1Body centre, roof, frame. A-pillar — 1Body centre, roof, frame. B-pillar — 1Body centre, roof, frame. Side member — 1Body, rear. Rear cross member — 1Body, rear. Rear cross panel — 1Body, rear. Luggage compartment floor — 1Body, rear. Rear longitudinal member — 1Body, rear. Side panel — 1Body, rear. Rear wheel housing — 1General information, Body. Basic information on body repairs — 1General information, Body. Explanation of symbols — 1General information, Body. Overview of materials used — 1General information, Body. Joining and separating techniques — 1General information, Body. Surface repair — 1General information, Body. Corrosion protection — 1General information, Body. Noise insulation — 1General information, Body. Plastic repair — 1General information, Body. Welding plastic attachments — 1General information, Body. General notes – windows — 1General information, Body. Glass repair — 1General information, Body. Use of adhesives — 1General information, Body. Self-adhesive components — 1General information, Body. Noises — 1General information, Body. Preparing for disposal — 1General information, Body. Leaks — 1General information, paint. Safety information — 1General information, paint. General information — 1Genuine products. Filler — 1Genuine products. Priming metal — 1Genuine products. Priming plastic materials — 1Genuine products. Surfacer — 1Genuine products. 2-pack top coats — 1Repair painting work. Paint finish – decorative strips and films — 1Repair painting work. Tips and tricks — 1Air conditioner. Overview of fitting locations — 1Air conditioner. Refrigerant circuit — 1Air conditioner. Valve unit of heat pump — 1Air conditioner. Air conditioner compressor — 1Air conditioner. Control motors — 1Air conditioner. Front heater and air conditioning unit — 1Air conditioner. Air duct — 1Air conditioner. Coolant circuit — 1Air conditioner. Other controlling and regulating components — 1Air conditioner. Air quality improvement system — 11-speed gearbox 0MH, rear, EQ310. Technical data — 11-speed gearbox 0MH, rear, EQ310. Gearbox mechanics,operation, construction,diff — 11-speed gearbox 0MH, rear, EQ310. Final drive, differential, differential lock — 1General information. High voltage — 1Electric drive EIP220, EIA200, EIA210. Technical data — 1Electric drive EIP220, EIA200, EIA210. Engine assy,cylinder block,crankcase — 1Electric drive EIP220, EIA200, EIA210. Engine cooling — 1Electric drive. High-voltage components, charging unit and voltage converter — 1Electric drive. Warning stickers — 1Electric drive. High-voltage battery unit, edge of upper part of battery housing without wax — 1Electric drive. High-voltage battery unit, edge of upper part of battery housing with wax — 1Electric drive. Power and control electronics for electric drive — 1Electric drive. Electric drive motor — 1Electric drive. Motor control unit — 1Electric drive. De-energising high-voltage system — 1Electric drive. Re-energise high-voltage system — 1Electric drive. Potential equalisation lines — 1Electric drive. Charging socket, with charging cable — 1Electric drive. Charging socket, with separate charging cable — 1Electric drive. Charging unit for high-voltage battery — 1Electric drive. Charging unit for high-voltage battery, with integrated voltage converter — 1Electric drive. Vehicle noise & engine sound — 1Electric drive. Accelerator pedal — 1Electric drive. Voltage converter — 1Electric drive. High-voltage cables, all-wheel drive — 1Electric drive. High-voltage cables, rear-wheel drive — 1Front suspension, drive shafts. Front axle — 1Front suspension, drive shafts. Subframe — 1Front suspension, drive shafts. Suspension strut, upper suspension link — 1Front suspension, drive shafts. Lower suspension link, swivel joint — 1Front suspension, drive shafts. Wheel bearing — 1Front suspension, drive shafts. Anti-roll bar — 1Rear suspension, drive shaft. Rear axle — 1Rear suspension, drive shaft. Subframe — 1Rear suspension, drive shaft. Anti-roll bar — 1Rear suspension, drive shaft. Suspension link, track rod — 1Rear suspension, drive shaft. Suspension strut, shock absorber, spring — 1Rear suspension, drive shaft. Wheel bearing assembly, trailing arm — 1Rear suspension, drive shaft. Drive shaft — 1Self-levelling air spring system. Electronically controlled damping — 1Self-levelling air spring system. Vehicle level sender — 1Wheels, tyres. axle align. Wheel alignment — 1Wheels, tyres. axle align. Wheels, tyres — 1Steering. Steering wheel — 1Steering. Steering column — 1Steering. Steering rack — 1Brake system. Technical data — 1ABS, ADR, TCS, EDL, ESP. Overview of fitting locations — 1ABS, ADR, TCS, EDL, ESP. Control unit and hydraulic unit — 1ABS, ADR, TCS, EDL, ESP. Sensors — 1Brake, brake mechanics. Front brake — 1Brake, brake mechanics. Rear brake — 1Brake, brake mechanics. Parking brake — 1Brake, brake mechanics. Brake pedal — 1Brakes, hydraulics, regulator, servo. Brake servo and brake master cylinder — 1Brakes, hydraulics, regulator, servo. Hydraulic system — 1Wheels and Tyres Guide. Wheels, tyres. axle align — 1Wheels, tyres. axle align. Instructions on using the guide — 1Wheels, tyres. axle align. Legislative and technical conditions — 1Wheels, tyres. axle align. Wheel change — 1Wheels, tyres. axle align. Fitting tyre — 1Wheels, tyres. axle align. Wheel bolts — 1Wheels, tyres. axle align. Information on tyres — 1Wheels, tyres. axle align. Handling problems — 1Wheels, tyres. axle align. Evaluating tyres — 1Wheels, tyres. axle align. Tyre wear — 1Starter-current supply-CC. Battery — 1Instruments, GCI. Dash panel insert — 1Instruments, GCI. Horn — 1Windscreen wipewash system. Windscreen wiper system — 1Windscreen wipewash system. Windscreen washer system — 1Windscreen wipewash system. Rear window wiper system — 1Windscreen wipewash system. Rear window washer system — 1Lights, lamps, switches outside. LED headlight — 1Lights, lamps, switches outside. LED matrix headlight — 1Lights, lamps, switches outside. Tail lights — 1Lights, lamps, switches outside. Lights in exterior mirror — 1Lights, lamps, switches outside. Number plate light — 1Lights, lamps, switches outside. Entry and start authorisation system — 1Lights, lamps, switches outside. Steering column switch module — 1Lights, lamps, switches outside. Towing bracket — 1Lights, lamps, switches inside, anti-theft system. Lights — 1Lights, lamps, switches inside, anti-theft system. Controls — 1Lights, lamps, switches inside, anti-theft system. Anti-theft alarm system — 1Lights, lamps, switches inside, anti-theft system. Cigarette lighter, socket — 1Wiring. Relay carriers, fuse holders, electronics boxes — 1Wiring. Control units — 1Infotainment. Componentscontrol units — 1Infotainment. Multifunction steering wheel — 1Driver assist systems. Senders, sensors, control units — 1Driver assist systems. Adaptive cruise control — 1Driver assist systems. Reversing camera system — 1Driver assist systems. Front camera for driver assist systems — 1Driver assist systems. Overhead view camera — 1Electrical system. Starter-current supply-CC — 1Electrical system. Windscreen wipe and wash system — 1Wiring. Wires and lines — 1Wiring. Cleaning contact surfaces — 1
~14min read
060120180240300200148N·mlb·ft
Tightening torque found on this page
  • Assembly overview – drive shaft
  • Loosening and tightening threaded connections of drive shaft
  • Removing and installing drive shaft
  • Dismantling and assembling drive shaft, constant velocity joint
  • Dismantling and assembling drive shaft, triple roller joint
  • Dismantling and assembling drive shaft, triple roller joint

Assembly overview – drive shaft

Assembly overview – drive shaft

The overview is shown for the left side of the vehicle as an example.

1 - Clamp

❏ Renew after removing

❏ → Rep. gr.42; Tensioning clamp for boot

2 - Boot

3 - Clamp

❏ Renew after removing

❏ → Rep. gr.42; Tensioning clamp for boot

4 - Outer constant velocity joint

❏ → Rep. gr.42; Dismantling and assembling drive shaft

5 - Bolt

❏ Renew after removing

❏ → Rep. gr.42; Loosening and tightening threaded connections of drive shaft

❏ M16 × 1.5 × 70

❏ 200 N·m +90°

6 - Retaining ring

❏ Renew after removing

7 - Drive shaft

❏ Depending on equipment/installation period

❏ Allocation → Electronic parts catalogue (ETKA)

8 - Retaining ring

❏ Renew after removing

9 - Clamp

❏ Renew after removing

❏ → Rep. gr.42; Tensioning clamp for boot

10 - Boot

❏ Renew after removing

11 - Clamp

❏ Renew after removing

❏ → Rep. gr.42; Tensioning clamp for boot

12 - Triple roller spider with rollers

❏ → Rep. gr.42; Dismantling and assembling drive shaft

13 - Joint body

❏ → Rep. gr.42; Dismantling and assembling drive shaft

14 - Retaining ring

❏ Renew after removing

Loosening and tightening threaded connections of drive shaft

Loosening and tightening threaded connections of drive shaft

Special tools and workshop equipment required

♦ socket -T10361A-

Removal and installation are described for the left side of vehicle as an example.

Removing

Vehicles with cap for wheel hub

– Remove wheel → Rep. gr.44; Removing and installing wheel.

– Remove cap for wheel hub.

– Remove wheel → Rep. gr.44; Removing and installing wheel.

All vehicles (continued)

Important

● The aid of an additional person is required for the subsequent work steps.

– Press brake pedal.

NOTICE

Risk of damage to wheel bearings from the vehicle’s own weight when threaded connections are loosened on wheel end.

– When threaded connections of wheel bearings have been loosened, the wheel bearings must not be subjected to load.

– It is not permissible to loosen threaded connections more than 90° when the vehicle is resting on its wheels.

– Vehicles without bolted wheel bearings must not be moved while standing on their wheels. If a vehicle nevertheless must be moved, observe the following: install outer joint, and tighten it to 120 N·m.

– Use socket -T10361A- to loosen bolt -1- max. 90° with vehicle standing on its wheels.

– Raise vehicle.

– Unscrew bolt -1-.

Installing

Install in reverse order of removal, observing the following:

Important

● The aid of an additional person is required for the subsequent work steps.

NOTICE

Risk of damage to wheel bearings from vehicle’s own weight when threaded connections of wheel bearings are loosened on wheel end.

– When threaded connections of wheel bearings are pretightened, the wheels must not be in contact with the ground.

– Press brake pedal.

– Tighten bolt -1- to specified torque.

– Lower vehicle onto its wheels.

– Tighten bolt -1- to further turning angle.

Tightening torques

♦ → Rep. gr.42; Assembly overview – drive shaft

Removing and installing drive shaft

Removing and installing drive shaft

Special tools and workshop equipment required

♦ Cleaning set -VAS 294 017-

♦ engine and gearbox jack -VAS 6931-

♦ hook -VAS 281 007-

♦ pressure tool -T10520A-

♦ support -VAS 6931/1-

♦ thrust piece -T10520/5-

Rear left vehicle level sender -G76- will henceforth be referred to as “rear vehicle level sender”.

Left parking brake motor -V282- and right parking brake motor -V283- are referred to hereafter as parking brake motor.

Rear right speed sensor -G44- and rear left speed sensor -G46- will henceforth referred to as “rear speed sensor”.

Removal and installation are described for the left side of vehicle as an example.

Removing

Pressing drive shaft out of wheel bearing unit

– Loosen threaded connection of drive shaft → Rep. gr.42; Loosening and tightening threaded connections of drive shaft.

– Remove wheel → Rep. gr.44; Removing and installing wheel.

– Remove rear centre underbody cladding → General body repairs, exterior; Rep. gr.66; Underbody cladding; Removing and installing rear centre underbody cladding.

– Insert thrust piece -T10520/5- -1- into pressure tool -T10520A- -2-.

– Secure pressure tool -T10520A- -A- to brake drum -1- using 3 wheel bolts -3-.

– Pull out drive shaft using pressure tool -T10520A-.

I - Tighten knurled nut -1- hand-tight

II - Using spanner -3-, turn only bolt -2-, not the pressure tool itself.

Removing drive shaft

– Press drive shaft out of wheel bearing unit → Anchor.

– Disconnect electrical connector -2- on parking brake motor -1-.

– Unclip electrical wire -1- from retainer -2- -arrows-.

– Disconnect electrical connector -2- from rear speed sensor -3-.

– Insert support -VAS 6931/1- -B- into engine and gearbox jack -VAS 6931- -A-.

– Secure support -VAS 6931/1- -B- to brake drum -1- using two wheel bolts -2-.

– Push wheel bearing housing -1- with engine and gearbox jack -VAS 6931- -B- and support -VAS 6931/1- -B- -A- upwards to take up weight.

– Unscrew nut -3-, and pull out bolt -4- on wheel bearing housing -1-.

– Unscrew bolt -5- from wheel bearing housing -1-.

– Unscrew bolt -2- from wheel bearing housing -1-.

NOTICE

Risk of damage to the drive shaft if the triple roller spider is pulled out of the joint body.

– Make sure that the drive shaft is not pulled out of the inner joint.

– Pull the outer constant velocity joint out of wheel bearing housing.

– Swivel rear brake and wheel bearing housing -1- upwards as far as possible with engine and gearbox jack -A-.

– Pull drive shaft out of wheel bearing housing.

– Secure drive shaft -1- to upper suspension link -2- using hook -VAS 281 007- -A-.

– Using assembly lever, push drive shaft -1- out of gearbox -2- -arrow-.

– Pull drive shaft -1- out of gearbox -2-, and remove it.

Installing

Install in reverse order of removal, observing the following:

– Renew gearbox oil seal → 1-speed gearbox 0MH, rear; Rep. gr.39; Oil seals; Renewing left oil seal or → 1-speed gearbox 0MH, rear; Rep. gr.39; Oil seals; Renewing right oil seal.

– Mask off jaws of commercially available water pump pliers -A- with adhesive tape to prevent damage to splines of drive shaft -2-.

– Position ends of new retaining ring -4- at ends of old retaining ring -1-.

– Apply water pump pliers -A-, and press old retaining ring -1- out of drive shaft groove -2-.

– New retaining ring -4- is pressed into drive shaft groove -2- at the same time.

– Make sure that retaining ring -4- is seated correctly.

– Position drive shaft in a straight line, and push it into gearbox with a “jolt” until drive shaft engages audibly.

Important

● Hold drive shaft by inner joint when inserting.

– Remove locking fluid from splines of drive shaft -arrow-.

– Clean splines of drive shaft -1-.

Important

● Cleaned areas must be free of lubricant.

– Screw pipe brush -VAS 294 017/1- onto handle -2-.

– Clean splines in wheel bearing unit -1- using pipe brush -VAS 294 017/1- -2-.

– Move pipe brush -VAS 294 017/1- -2- in direction of -arrows A-.

– Turn pipe brush -VAS 294 017/1- -2- in direction of -arrow B- when doing this.

Important

● Pipe brush -VAS 294 017/1- -2- may only be turned in direction of -arrow B-.

– Repeat procedure with pipe brush -VAS 294 017/2-.

Important

● Cleaned areas must be free of lubricant.

– Apply locking fluid centrally to splines of drive shaft -1- all around -arrow-. Allocation → Electronic parts catalogue (ETKA).

– → Rep. gr.42; Raise wheel bearing in unladen position.

– Carry out wheel alignment → Rep. gr.44; Wheel alignment.

Tightening torques

♦ → Rep. gr.42; Assembly overview – drive shaft

♦ → Rep. gr.42; Assembly overview – suspension link

♦ → Rep. gr.42; Assembly overview – track rod

♦ → Rep. gr.42; Assembly overview – spring control arm

Dismantling and assembling drive shaft, constant velocity joint

Dismantling and assembling drive shaft, constant velocity joint

– Remove drive shaft → Rep. gr.42; Removing and installing drive shaft.

– Clamp drive shaft -1- in vice -A- using jaw protectors -B-.

– Open clamps -2- and -4- for boot -3-.

– Push back boot -3- on drive shaft -1-.

– Remove grease, and clean drive shaft -1-.

– Drive constant velocity joint -1- off drive shaft -2- using drift -A-.

– Make sure to position drift -A- exactly at ball hub -3- of constant velocity joint -1-.

– In the process, change position of drift -A- along ball hub -3- accordingly.

Installing

Install in reverse order of removal, observing the following:

– Clean constant velocity joint and drive shaft -1-.

– Use commercially available water pump pliers -A-.

– Mask off jaws of water pump pliers -A- with adhesive tape to prevent damage to splines of drive shaft -1-.

– Position ends of new retaining ring -2- at ends of old retaining ring -3-.

– Apply water pump pliers -A-, and press old retaining ring -3- out of drive shaft groove -1-.

– New retaining ring -2- is pressed into drive shaft groove -1- at the same time.

– Make sure that retaining ring -2- is seated correctly.

– Slide on clamp with smaller diameter.

– Push boot onto drive shaft.

– Slide on clamp with larger diameter.

– Knock constant velocity joint onto drive shaft with plastic hammer until retaining ring engages.

– Press in half of total amount of grease from repair kit at rear of constant velocity joint.

– Press remaining amount of grease from repair kit into boot.

– Push boot with clamp onto constant velocity joint.

– → Rep. gr.42; Tensioning clamp for boot.

Dismantling and assembling drive shaft, triple roller joint

Dismantling and assembling drive shaft, triple roller joint

Special tools and workshop equipment required

♦ assembly tool -T10065/1-

♦ assembly tool -T10065/4-

♦ press tool -VW409-

♦ retaining clip pliers -VAS 5503A-

♦ thrust plate -VW401-

♦ tube -VW416B-

Removing

– Clamp drive shaft -1- in vice -A- using jaw protectors -B-.

– Open clamps -2- and -4- for boot -3-.

– Push back boot -3- on drive shaft -5-.

– Pull joint body -1- off drive shaft.

– Remove grease, and clean drive shaft -5-.

– Remove retaining ring -3- using retaining clip pliers -VAS 5503A- -C-.

– Insert thrust plate -VW401- -C- and thrust plate -VW401- -D- into workshop press.

– Fit assembly tool -T10065/4- -B- to drive shaft -2-.

– Push assembly tool -T10065/1- -A- with opening over drive shaft -2-.

– Insert drive shaft -2- with assembly tool -T10065/4- -B- into assembly tool -T10065/1- -A-.

– Insert drive shaft -2- with assembly tool -T10065/4- -B- and assembly tool -T10065/1- -A- between thrust plate -VW401- -C- and thrust plate -VW401- -D-.

– Push thrust plate -VW401- -C- and thrust plate -VW401- -D- together.

– Fit drive shaft with assembly tool -T10065/4- -B- and assembly tool -T10065/1- -A- onto thrust plate -VW401- -C- and thrust plate -VW401- -D-.

– Make sure that triple roller spider -1- is properly seated on assembly tool -T10065/4- -B-.

– Mount press tool -VW409- -E- on drive shaft -2-.

– Press triple roller spider -1- off drive shaft -2-.

– Pull boot off drive shaft -2-.

– Clean drive shaft -2-, joint body and groove for seal.

Installing

Install in reverse order of removal, observing the following:

– Push small clamp for boot onto drive shaft.

– Push boot onto drive shaft.

– Clamp drive shaft -1- in vice -A- using jaw protectors -B-.

– Clean triple roller spider -1-.

– Fit triple roller spider -1- onto drive shaft -2-.

Important

● Chamfer -arrow- on triple roller spider -1- points towards drive shaft -2-.

– Drive triple roller spider -1- onto drive shaft -2- using tube -VW416B- -C-.

– Drive on triple roller spider -1- as far as stop.

– Install new retaining ring -3- using retaining clip pliers -VAS 5503A- -C-.

– Make sure it is seated correctly.

– Press half of total amount of grease from repair kit into triple roller joint.

– Slide on clamp with larger diameter.

– Slide joint body over rollers and hold it there.

– Press remaining amount of grease from repair kit into back of triple roller joint.

– Push boot with clamp onto joint body.

– → Rep. gr.42; Tensioning clamp for boot.

Dismantling and assembling drive shaft, triple roller joint

Dismantling and assembling drive shaft, triple roller joint

Special tools and workshop equipment required

♦ assembly tool -T10065/1-

♦ assembly tool -T10065/4-

♦ press tool -VW409-

♦ retaining clip pliers -VAS 5503A-

♦ thrust plate -VW401-

♦ tube -VW416B-

Removing

– Clamp drive shaft -1- in vice -A- using jaw protectors -B-.

– Open clamps -2- and -4- for boot -3-.

– Push back boot -3- on drive shaft -5-.

– Pull joint body -1- off drive shaft.

– Remove grease, and clean drive shaft -5-.

– Remove retaining ring -3- using retaining clip pliers -VAS 5503A- -C-.

– Insert thrust plate -VW401- -C- and thrust plate -VW401- -D- into workshop press.

– Fit assembly tool -T10065/4- -B- to drive shaft -2-.

– Push assembly tool -T10065/1- -A- with opening over drive shaft -2-.

– Insert drive shaft -2- with assembly tool -T10065/4- -B- into assembly tool -T10065/1- -A-.

– Insert drive shaft -2- with assembly tool -T10065/4- -B- and assembly tool -T10065/1- -A- between thrust plate -VW401- -C- and thrust plate -VW401- -D-.

– Push thrust plate -VW401- -C- and thrust plate -VW401- -D- together.

– Fit drive shaft with assembly tool -T10065/4- -B- and assembly tool -T10065/1- -A- onto thrust plate -VW401- -C- and thrust plate -VW401- -D-.

– Make sure that triple roller spider -1- is properly seated on assembly tool -T10065/4- -B-.

– Mount press tool -VW409- -E- on drive shaft -2-.

– Press triple roller spider -1- off drive shaft -2-.

– Pull boot off drive shaft -2-.

– Clean drive shaft -2-, joint body and groove for seal.

Installing

Install in reverse order of removal, observing the following:

– Push small clamp for boot onto drive shaft.

– Push boot onto drive shaft.

– Clamp drive shaft -1- in vice -A- using jaw protectors -B-.

– Clean triple roller spider -1-.

– Fit triple roller spider -1- onto drive shaft -2-.

Important

● Chamfer -arrow- on triple roller spider -1- points towards drive shaft -2-.

– Drive triple roller spider -1- onto drive shaft -2- using tube -VW416B- -C-.

– Drive on triple roller spider -1- as far as stop.

– Install new retaining ring -3- using retaining clip pliers -VAS 5503A- -C-.

– Make sure it is seated correctly.

– Press half of total amount of grease from repair kit into triple roller joint.

– Slide on clamp with larger diameter.

– Slide joint body over rollers and hold it there.

– Press remaining amount of grease from repair kit into back of triple roller joint.

– Push boot with clamp onto joint body.

– → Rep. gr.42; Tensioning clamp for boot.