General information on paint

Plastic primer

~2min read

Adhesion promoter (translucent)

Designation:

  • Adhesion promoter -ALO 822 000 10- (translucent)

Product description

The translucent adhesion promoter is a universal one-component adhesion promoter for all common plastic parts on the exterior of vehicles.

This adhesion promoter features reliable adhesion, high elasticity and easy processing.

Application information

Substrate

Suitable substrates:

All common plastic parts on the exterior of vehicles.

  • PP, EPDM, ABS, PC, PPO, PA, R-TPU, PBTP, PVC
  • PUR, PUR-Weichschaum
  • UP-GF

Pretreatment of substrates:

The substrate must be free of release agents.

Temper plastic parts for 60 minutes at +60 °C before cleaning so that the release agents "sweat out".

- Clean with plastic cleaner, antistatic -LVM 001 001 A2- or with the milder silicone remover, long -LVM 020 100 A5-.


Note

  • The effort required for cleaning depends on the type and amount of release agent used. To support cleaning, we recommend using an abrasive pad.
  • Allow the thinner to flash off thoroughly (e.g. by air drying overnight at room temperature or for 30-40 minutes at +60 °C).
VW UP. Allgemeine Informationen Lack

- Before priming, clean again lightly with plastic cleaner, antistatic -LVM 001 001 A2- or silicone remover, long -LVM 020 100 A5- (antistatic effect).

VW UP. Allgemeine Informationen Lack

Processing

Thinning:

- Do not add any thinner!

Application method "Spray pass"

VW UP. Allgemeine Informationen Lack

- Processing viscosity 4 mm at +20 °C, DIN 53211


Note

Do not add any thinner! Supply viscosity is the same as processing viscosity.

Processing viscosity 4 mm, gravity cup gun "Compliant" and "HVLP":

DIN 4 mm: 11 seconds

VW UP. Allgemeine Informationen Lack

- Set the spray nozzle (see manufacturer's specifications): "Compliant" 1.2-1.4 mm.

- Set the spray nozzle (see manufacturer's specifications): "HVLP" 1.3-1.5 mm.

- Set spray pressure (see manufacturer's specifications): "Compliant" 2.0–2.5 bar.

- Set the atomizing pressure (see manufacturer's specifications): "HVLP" 0.7 bar.

VW UP. Allgemeine Informationen Lack

- A closed spray pass is 1-2 µm.

VW UP. Allgemeine Informationen Lack

Drying

Air drying at +20 °C room temperature, can be overcoated after 15 minutes

VW UP. Allgemeine Informationen Lack

Rework

VW UP. Allgemeine Informationen Lack

After the flash-off time at +20 °C, can be overcoated with 2K HS filler elasticized with elasticizer -ALZ 011 001-.

Can then be topcoated with:

  • Waterborne basecoat and 2K HS clearcoat
  • 2K HS topcoat
VW UP. Allgemeine Informationen Lack

Personal protective equipment:

  • Observe the safety data sheet
  • Wear personal protective equipment during application

Characteristics

VW UP. Allgemeine Informationen Lack


Storage

The guaranteed storage stability is 24 months from the production date. Usable at the latest until the date stated on the label when stored in closed original containers at +20 °C.

VW UP. Allgemeine Informationen Lack

Storage conditions

The prescribed storage temperature is +20 °C (must not fall below +5 °C).

VW UP. Allgemeine Informationen Lack