General information on paint

Wax underbody protection

~5min read

Wax underbody protection -D 316 D38 A2-

Designation:

  • Wax underbody protection -D 316 D38 A2-

Product description

Wax underbody protection -D 316 D38 A2- is a solvent-based anti-corrosion agent based on wax and lanolin, with added polymers and rust-inhibiting additives.

This results in high toughness and relatively high abrasion resistance for a wax.

The material creeps into the pores of the PVC coating, displaces moisture, seals the pores, and is water-repellent, tenaciously adhesive and non-slip.

After drying, it forms a light beige, transparent, non-tacky, water-repellent film.

Due to its transparency, the product meets TÜV requirements (the underbody remains inspectable).

The dry film has good adhesion and corrosion protection properties and, due to its toughness and resistance, is very durable.

Application Information Wax underbody protection -D 316 D38 A2-

Application

  • The material is mainly used on the underbody and especially for aftertreatment and care of all protective coatings, such as those based on PVC, PVC/wax, bitumen/rubber/resin.
  • It can also be used to treat chassis parts such as axles, wheel suspensions and springs. These parts turn grey over the years and often show first signs of rust. The treatment refreshes the color, considerably improving the appearance. At the same time, the chassis parts receive corrosion protection.


Note

  • Before starting work, read the safety data sheet for precautions and safety advice.
  • Even for products that do not require labeling, observe the precautions usual for chemical products.

Processing

  • Surfaces to be treated with wax underbody protection must be thoroughly cleaned beforehand, and rust must be removed.
  • The surfaces must be dry, free of grease and dirt, and largely free of dust.
  • Wax underbody protection may only be applied to dry surfaces. On older vehicles, check for rust formation.
  • Rust must be removed using a wire brush.
  • Before starting work, cover the vehicle, especially the door windows.
  • Wax underbody protection can be applied in one pass on vertical surfaces. To avoid spray shadows, it is advisable to spray in a cross pattern.
  • After drying overnight, the vehicle can be used again. Full curing requires between 24 and 48 hours.
  • For processing from the 1 l can, use the underbody protection gun. Shake the can thoroughly before use.
  • Recommended wet film thickness approx. 200 μm, processing air pressure approx. 3-5 bar.
  • Wax underbody protection can also be processed with a pressure cup gun if the Venturi hook probe (16139 SATA) is used. The processing pressure is approx. 3-4 bar. With a 750 mm long flexible guide hose, the hook can be guided very well with the 7 mm Venturi nozzle.


Caution!

Do not spray onto joints, engine, transmission, propeller shaft, exhaust, catalytic converter or brake systems.

Blow out the UBS gun immediately after use, then flush it through with plastic cleaner -D 195 850 A1-.

A clogged gun can cause the can to burst!

Observe the operating instructions for the UBS gun!

Cleaning

  • Splashes and overspray should be removed immediately with plastic cleaner -D 195 850 A1-. Material residues can also be easily removed with white spirit or kerosene.
  • Larger areas can also be cleaned with a steam jet cleaner.
  • For this reason, an underbody treated with wax underbody protection must not be cleaned with steam jet equipment, unless the old coating is to be removed before retreatment.

Technical Data


Wax underbody protection -D 316 000 A1-

Designation:

  • Wax underbody protection -D 316 000 A1-

Product description

Wax underbody protection -D 316 000 A1- is an excellent long-term corrosion protection.

The wax underbody protection is based on a solvent-free, oxidatively curing system and provides optimum corrosion protection for the underbody area of bodies.

This corrosion protection provides very good adhesion to metallic surfaces at both very low and high temperatures.

The product forms a light brown, elastic and non-tacky coating.

Elevated temperature is not required for film cross-linking.

Application Information Wax underbody protection -D 316 000 A1-

Application

  • The material is mainly used in the vehicle area.
  • Make sure the substrates are dry.
  • The ready-to-use product is applied by brushing at material temperatures of 20-35 ºC.
  • If the application technique requires it, the material can be gently heated to up to 45 ºC immediately (< 5 minutes) before application.
  • The oxidatively curing product may form a skin on the surface after a short time. This has no effect on the corrosion protection or other properties.

Properties

  • Solvent-free
  • Active content 100 %
  • Excellent long-term corrosion protection
  • Good adhesion properties
  • Low tendency to drip
  • Flexible at low temperatures
  • Long shelf life


Note

  • Before starting work, read the safety data sheet for precautions and safety advice.
  • Even for products that do not require labeling, observe the precautions usual for chemical products.

Processing

  • The surfaces to be treated must be dry and free of grease and dust.
  • Bring the wax underbody protection to processing temperature (20-35 ºC).
  • Apply the material to the body parts to be protected and spread it with a brush.

Technical Data


Wax spray -D 322 100 M2-

Designation:

  • Wax spray -D 322 100 M2-

Product description

Wax spray -D 322 100 M2- is a long-term corrosion protection agent. After drying, the product forms a light brown, wax-like film. Due to its hardness, the wax spray provides good protection against mechanical stress.

Application Information Wax spray -D 322 100 M2-

Application

  • The material is mainly used in the vehicle area, but also as temporary corrosion protection for tools and machines.
  • The wax spray does not attack vehicle paint and adheres to almost all substrates.


Note

  • Before starting work, read the safety data sheet for precautions and safety advice.
  • Even for products that do not require labeling, observe the precautions usual for chemical products.

Processing

  • Bring the wax spray to room temperature (16-20 ºC).
  • Shake the spray can briefly before use.
  • The surfaces to be treated (underbodies, wheel housings, inner door panels) must be dry and free of grease and dust.
  • Spray the wax spray evenly in a cross pattern from a distance of 20-30 cm.


Caution!

Do not spray onto joints, engine, transmission, propeller shaft, exhaust, catalytic converter or brake systems.

Technical Data