General information on paint

Body filler

~12min read
1special tools

2K steel filler set

Designation:

  • 2K steel filler set -DA 787 300 A2-

Product description

This filler is a polyester filler with a metal powder mixture for producing contour-accurate surfaces on highly stressed body panels. It is intended in particular as a replacement for leaded tin-plate solder.

This filler is easy to draw and sand, with high sag resistance and high temperature resistance, which makes it particularly suitable for overpainting.


Note

At temperatures above 30 °C and/or relative air humidity above 80 %, the 2K hardener, long -LVM 018 100 A2- must be used.

Application information

Substrate

Suitable substrates:

  • Steel
  • metallic substrates in general
  • galvanised sheet steel

Pretreatment of substrates:

- Thoroughly degrease and sand the substrate. The substrates must be prepared with the "Wire brush blaster set, pneumatic -VAS 6446-". The surface must be bare metal, sanded with P40 grit. If necessary, clean the contaminated area again and then remove cleaning residues with the wire brush blaster.

VW UP. Allgemeine Informationen Lack

- Before reworking, clean again with a silicone remover.

Processing

VW UP. Allgemeine Informationen Lack

Application method: Applying filler

VW UP. Allgemeine Informationen Lack

Mixing ratio:

- The two components are mixed in a ratio of 1 part by volume hardener liquid to 2.5-3 parts by volume powder, or 10 grams of hardener liquid to 58 grams of powder, to form a fillable product.


Note

Overdosing the hardener liquid must be avoided, as this adversely affects the final strength and adhesion properties of the filler.

Pot life:

- The pot life at +20 °C is approx. 4-6 minutes.

Reaction temperature:

- The reaction temperature must be at least +5 °C.

VW UP. Allgemeine Informationen Lack

Drying

Air drying:

- Cure using a short-wave IR emitter

  • Flash off at +20 °C for approx. 10 minutes
  • Pre-cure: 10 minutes at approx. 50 °C
  • Full cure stage 1, 10 minutes at 75 °C
  • Full cure stage 2, 10 minutes at 85 °C
VW UP. Allgemeine Informationen Lack

Sandability

- Excess material that is clearly visible can be removed before the thermal final curing process, e.g. with a body plane.

- Then sand to contour with dry sanding paper, P80 grit.

Overcoating:

No restrictions

Characteristics

VW UP. Allgemeine Informationen Lack


Storage

The guaranteed storage stability is 12 months from the production date. Must be used by the date stated on the label at the latest when stored in sealed original containers at +20 °C.

Storage conditions

- Store cool and dry. Storage temperature +20 °C.


Note

  • Process only in well-ventilated areas.
  • Wearing protective gloves and a dust mask is recommended.
  • Use of a sanding dust extraction system is recommended.
VW UP. Allgemeine Informationen Lack

2K fine filler

Designation:

  • 2K fine filler -LSP 784 002 A2-

Product description

The 2K fine filler is a very fine, thixotropic polyester filler.

This filler is suitable for small repairs.

Application information

Properties

  • fine and pore-free
  • easy to draw
  • easy to sand
  • high elasticity for spot-repairing plastic surfaces

Substrate

Suitable substrates:

  • Steel
  • Aluminium
  • glass-fibre reinforced plastics
  • Original or factory paint
  • cured 2K surfacers/2K primers
  • plastic parts primed with thin coat of 2K plastic adhesion primer -LKF 696 009 A2-/-LKF 696 040 A2- or adhesion promoter -ALO 822 000 10-
  • surfaces pre-worked with 2K polyester filler


Caution!

This filler must not be applied over PVB (acid-curing) adhesion primers or 1K primers (e.g. synthetic resin).

Application over thermoplastic or elastic-tough paint finishes is also not possible. In these cases, apply filler only to bare sheet metal.

Pretreatment of substrates:

- Degrease thoroughly and sand.

- Bare metal surfaces must be isolated with 2K wash primer -LHV 043 000 A2- and then filled with 2K HS performance filler. After drying, sand the filler.

- On UP-GF substrates, clean the component of release agent residues and sand.

VW UP. Allgemeine Informationen Lack

- Use a suitable cleaner before overcoating to ensure a clean, residue-free surface.

VW UP. Allgemeine Informationen Lack

Processing

Application method:

- Filling by spatula

VW UP. Allgemeine Informationen Lack

Mixing ratio:

- Add 2-3 wt.% of 2K hardener -LVM 018 000 A1/A2- or, especially at high temperatures, the 2K hardener, long -LVM 018 100 A2-.


Note

Avoid overdosing the hardener paste to prevent bleed-through, especially with fluorescent day-glow colors and light metallic shades.

Pot life:

- at +20 ºC room temperature approx. 3-5 minutes

Reaction temperature:

- at least +5 ºC

VW UP. Allgemeine Informationen Lack

Drying

Air drying:

- at +20 ºC room temperature approx. 20-30 minutes

VW UP. Allgemeine Informationen Lack

Infrared drying:

  • short-wave emitter 3 minutes (at 50 % output)
  • medium-wave emitter 5 minutes
VW UP. Allgemeine Informationen Lack

Sandability

Following the above drying times:

- Dry pre-sanding with abrasive paper, grit P180-240

- Dry final sanding with abrasive paper, grit P240-320

VW UP. Allgemeine Informationen Lack

- Wet pre-sanding with abrasive paper, grit P240-320

- Wet final sanding with abrasive paper, grit P600-800


Note

  • When wet sanding, make sure the surface is thoroughly squeegeed and dried.
  • Heat resistance up to +80 ºC.
VW UP. Allgemeine Informationen Lack

Overcoating

Recommended build-up:

  • 1K wash primer -LVM 044 007 A2-/-LVM 044 171 A2-
  • 2K wash primer -LHV 043 000 A2- and 2K HS vario filler
  • 2K plastic adhesion primer -LKF 696 009 A2-/-LKF 696 040 A2-
  • Adhesion promoter -ALO 822 000 10- non-flexibilized 2K HS filler (for plastic parts)

- Then overcoat with topcoat.

VW UP. Allgemeine Informationen Lack

Personal protective equipment:

  • Observe the safety data sheet
  • Wear personal protective equipment during application

Characteristics

VW UP. Allgemeine Informationen Lack


Storage

Guaranteed storage stability is 12 months from the production date. Usable at the latest until the date stated on the label when stored in closed original containers at +20 ºC.

Storage conditions

- Storage temperature +20 ºC (+30 ºC must not be exceeded).

VW UP. Allgemeine Informationen Lack

2K fine filler, flexible

Designation:

  • 2K fine filler, flexible -LSP 787 100 A1-

Product description

The 2K fine filler, flexible -LSP 787 100 A1- is a two-component filler with high filling properties.

The product does not sag and has excellent adhesion to a wide range of substrates.

This filler is particularly suitable for plastics.

Other areas of application:

  • Repair of body plastic exterior panels after surface damage with material removal (scratches, holes, cracks), but without through-cracks
  • for filling KU plastics that were previously repaired with the plastic repair set -D 007 700-
  • for skim-filling a repair area to avoid marking through

Application information

Properties

  • uniform, fine creamy consistency
  • high filling properties - no sinking
  • fast curing
  • excellent sandability
  • good adhesion to metal and plastic

Substrate

Suitable substrates:

  • Steel
  • galvanised sheet steel
  • Aluminium
  • on all cleaned and sanded plastics in vehicle applications
  • glass-fiber reinforced plastics (UP-GF)
  • well-sanded existing or original paint finishes
  • cured 2K surfacers/2K primers

Pretreatment of substrates:

- Degrease thoroughly and sand.

- Bare metal surfaces must be isolated with 2K wash primer -LHV 043 000 A2- and then filled with 2K HS performance filler. After drying, sand the filler.

- On UP-GF substrates, clean the component of release agent residues and sand.

VW UP. Allgemeine Informationen Lack

- Before overcoating, clean again with long-life silicone remover -LVM 020 100 A5- or silicone remover -LVM 020 000 A5-.

VW UP. Allgemeine Informationen Lack

Overcoating

Recommended build-up:

  • Can be fine-filled over itself.
  • Overfill with 2K fine filler -LSP 784 002 A2- or 2K spray filler -ALN 788 007- (except on galvanized sheet steel).
  • Prime bare spots and filler patches with 2K wash primer -LHV 043 000 A2- and then fill with 2K HS performance filler.

- Then overcoat with topcoat.


Note

Before filling, the entire area must be dry-sanded with abrasive paper P280-400.

Application table

VW UP. Allgemeine Informationen Lack



Caution!

This filler must not be applied over PVB (acid-curing) adhesion primers or 1K primers (e.g. synthetic resin).

Application over thermoplastic or elastic-tough paint finishes is also not possible. In these cases, apply filler only to bare sheet metal.


Note

  • Before filling, the entire area must be dry-sanded with grit P280-320.
  • Avoid overdosing the hardener paste to prevent bleed-through, especially with fluorescent day-glow colors and light metallic shades.
  • Reaction temperature at least +5 ºC.

2K spray filler

Designation:

  • 2K spray filler -ALN 788 007-

Product description

The 2K spray filler -ALN 788 007- is a 2K spray filler for vehicle repair, used to level out coarse unevenness.

Other areas of application:

  • particularly suitable for large-area application
  • very good sprayability.
  • easy application and good sag resistance
  • good flow
  • VOC value < 250 g/l

Application information

Substrate

Suitable substrates:

  • cleaned and sanded steel sheet primed with 2K wash primer -LHV 043 000 A2- or 1K wash primer -LVM 044... A2- and then isolated with 2K HS filler, galvanized/electrolytically galvanized steel sheet, or aluminum
  • cured, solvent-resistant, well-preserved and sanded original or existing paint finish
  • surfaces filled with 2K polyester filler
  • release-agent-free, cleaned and sanded UP-GF substrates


Caution!

This filler must not be applied over PVB (acid-curing) adhesion primers or 1K primers (e.g. synthetic resin).

Application over thermoplastic or elastic-tough paint finishes is also not possible.

For optimal corrosion protection, we recommend pre-priming remaining rust spots on edges and corners as well as bare sanded areas with 2K wash primer -LHV 043 000 A2- or 1K wash primer -LVM 044... A2-, and then isolating with 2K HS filler.

Pretreatment of substrates:

- Degrease thoroughly and sand.

- On UP-GF substrates, clean the component of release agent residues and sand.

VW UP. Allgemeine Informationen Lack

- On all substrates, use a suitable cleaner before overcoating to ensure a clean, residue-free surface.

VW UP. Allgemeine Informationen Lack

Processing

Mixing ratio:

- Add 5 vol.% of 2K hardener -LHA 841 000 A2-.

- Pot life 20-30 minutes at +20 ºC

- The reaction temperature must be at least +15 ºC.

VW UP. Allgemeine Informationen Lack

Application method "Spray pass"

VW UP. Allgemeine Informationen Lack

- Set processing viscosity at a material temperature of +20 ºC.

- Set spray nozzle to 2-2.5 mm (see manufacturer's specifications).

- Set spray pressure to 2-3 bar (see manufacturer's specifications).

VW UP. Allgemeine Informationen Lack

- 5 spray passes produce 500-600 µm (film builds up to 1000 µm are possible).

Application method "Spread on"


Note

For the application method "Spread on", spread the material once in a single continuous pass.

VW UP. Allgemeine Informationen Lack

Drying

Air drying at +20 ºC room temperature:

- Sandable after 2 hours

VW UP. Allgemeine Informationen Lack

Forced drying:

- Flash-off time at least 10 minutes

VW UP. Allgemeine Informationen Lack

- Drying time 30 minutes at a part temperature of +60 ºC

VW UP. Allgemeine Informationen Lack

Infrared drying:

- Flash-off time at least 5 minutes

VW UP. Allgemeine Informationen Lack

- Drying time 10-12 minutes, short-wave infrared lamp at 50 % power

- Drying time 15-20 minutes, medium-wave infrared lamp


Note

Temperature resistance up to +80 ºC!

VW UP. Allgemeine Informationen Lack

Further processing

Dry sanding:

VW UP. Allgemeine Informationen Lack

- Pre-sanding dry with P120 - 220 grit sandpaper

- Final sanding dry with P240 - 400 grit sandpaper


Note

Dry sanding should be carried out with a suitable sanding machine and dust extraction.

VW UP. Allgemeine Informationen Lack

Overcoating

- Refinish with 1K wash primer -LVM 044... A2- (only at sand-through spots)

- Topcoat with waterborne basecoat and 2K HS clearcoat and 2K HS topcoat

VW UP. Allgemeine Informationen Lack

Personal protective equipment:

  • Observe the safety data sheet
  • Wear personal protective equipment during application

Characteristics

VW UP. Allgemeine Informationen Lack


Storage

Guaranteed storage stability is 12 months from the production date. Usable at the latest until the date stated on the label when stored in closed original containers at +20 ºC.

Storage conditions

- Storage temperature +20 ºC (+30 ºC must not be exceeded).

VW UP. Allgemeine Informationen Lack

2K IR premium filler

Designations:

  • 2K IR premium filler -LSP 787 220 A1-
  • 2K IR premium filler -LSP 787 220 A2-
  • 2K IR premium filler -LSP 787 220 A3-

Product description

The 2K IR premium filler -LSP 787 220 A1/A2/A3- is a high-quality polyester filler for vehicle repair refinishing.

Other areas of application:

  • all common metallic substrates
  • very good adhesion, including on galvanized substrates
  • good sandability
  • easy, pore-free drawing down
  • excellent for IR drying

Application information

Substrate

Suitable substrates:

  • Steel sheet
  • galvanised sheet steel
  • Aluminium
  • well-sanded original or old paint finish
  • cured, primed 2K surfacers/2K primers
  • release-agent-free, cleaned and sanded UP-GF substrates


Caution!

This filler must not be applied over PVB (acid-curing) adhesion primers or 1K primers (e.g. synthetic resin).

Application over thermoplastic or elastic-tough paint finishes is also not possible.

Pretreatment of substrates:

- Degrease thoroughly and sand.

- Bare metal surfaces must be isolated with 2K wash primer -LHV 043 000 A2- and then filled with 2K HS performance filler. After drying, sand the filler.

- On UP-GF substrates, clean the component of release agent residues and sand.

- On all substrates, clean with a suitable cleaning agent before refinishing to ensure a clean, residue-free surface.

VW UP. Allgemeine Informationen Lack

Processing

Application method:

- Filling by spatula

VW UP. Allgemeine Informationen Lack

Mixing ratio:

- Add 2-3 wt.% of 2K hardener -LVM 018 000 A1/A2- or, especially at high temperatures, the 2K hardener, long -LVM 018 100 A2-.


Note

Avoid overdosing the hardener paste to prevent bleed-through, especially with fluorescent day-glow colors and light metallic shades.

Pot life:

- At +20 ºC room temperature approx. 2-4 minutes

Reaction temperature:

- At least +5 ºC

VW UP. Allgemeine Informationen Lack

Drying

Air drying:

- At +20 ºC room temperature approx. 20-30 minutes

VW UP. Allgemeine Informationen Lack

Infrared drying:

  • short-wave emitter 3 minutes (at 50 % output)
  • medium-wave emitter 5 minutes
VW UP. Allgemeine Informationen Lack

Sandability

Following the above drying times:

- Pre-sanding dry with P80-240 grit sandpaper

- Final sanding dry with P240-400 grit sandpaper


Note

Temperature resistance up to +80 ºC!

VW UP. Allgemeine Informationen Lack

Overcoating

Recommended build-up:

  • Can be fine-filled over itself.
  • Overfill with 2K fine filler -LSP 784 002 A2- or 2K spray filler -ALN 788 007- (except on galvanized sheet steel).
  • Re-prime sand-through spots and filler spots with 2K wash primer -LHV 043 000 A2-, then fill with 2K HS performance surfacer.

- Then overcoat with topcoat.


Note

Before filling, the entire area must be dry-sanded with abrasive paper P280-400.

VW UP. Allgemeine Informationen Lack

Personal protective equipment:

  • Observe the safety data sheet
  • Wear personal protective equipment during application

Characteristics

VW UP. Allgemeine Informationen Lack


Storage

Guaranteed storage stability is 12 months from the production date. Usable at the latest until the date stated on the label when stored in closed original containers at +20 ºC.

Storage conditions

- Storage temperature +20 ºC (+30 ºC must not be exceeded).

VW UP. Allgemeine Informationen Lack

2K diamond aluminum filler

Designation:

  • 2K diamond aluminum filler, powder -DA 004 200 A2-
  • 2K diamond aluminum filler, hardener -DA 004 201 A1-
  • 2K diamond aluminum filler, hardener -DA 004 211 A1-

Product description

This filler is a polyester filler with universal application and particular suitability for aluminum panel repairs.

Its field of application is passenger car repair.

This filler is easy to draw down and sand, with high sag resistance and high temperature resistance, which makes it particularly suitable for topcoating.


Note

At temperatures above 30 ºC and/or a relative humidity above 80 %, the hardener -DA 004 211 A1- must be used.

Application information

Substrate

Suitable substrates:

  • Aluminium

Pretreatment of substrates:

VW UP. Allgemeine Informationen Lack

- Degrease and sand the substrate thoroughly. The substrates must be prepared with the "Brush blaster set, pneumatic -VAS 6446-". The surface must be bare metal, sanded with P40 grit. If necessary, clean the contaminated area again, then remove cleaning residues again with the brush blaster.

VW UP. Allgemeine Informationen Lack

Processing

Application method:

- Filling by spatula

VW UP. Allgemeine Informationen Lack

Mixing ratio:

- Mix the two components to a fillable product in the ratio of 1 part by volume liquid hardener to 2.5-3 parts by volume powder, or 10 grams liquid hardener to 25 grams powder.


Note

Overdosing the hardener liquid must be avoided, as this adversely affects the final strength and adhesion properties of the filler.

Pot life:

- Pot life at +20 ºC room temperature approx. 4-6 minutes

Reaction temperature:

- At least +5 ºC

Drying

VW UP. Allgemeine Informationen Lack

Air drying:

VW UP. Allgemeine Informationen Lack

- Flash off approx. 10 minutes

- Cure using a short-wave IR emitter

  • Pre-cure: 10 minutes at 50 ºC
  • Full cure stage 1: 10 minutes at 75 ºC
  • Full cure stage 2: 10 minutes at 85 ºC
VW UP. Allgemeine Informationen Lack

Sandability

- Obviously excess material can be removed with a body plane before the final thermal curing process. Then sand to contour with P80 dry sandpaper.

Overcoating:

No restrictions


Note

  • Process only in well-ventilated areas.
  • Wearing a dust mask and protective gloves is recommended.
  • Use of a sanding dust extraction system is recommended.

Characteristics

VW UP. Allgemeine Informationen Lack


Storage

Guaranteed storage stability is 12 months from the production date. Usable at the latest until the date stated on the label when stored in closed original containers at +20 ºC.

Storage conditions

- Store cool and dry.

- Storage temperature +20 ºC

VW UP. Allgemeine Informationen Lack