General information on paint

Additional Materials

~8min read
1special tools

Matting component -ALN 775 106-

Designation:

  • Matting component -ALN 775 106-

Product description

Matting component -ALN 775 106- produces a matte topcoat finish on plastic paint jobs when combined with 2K HS topcoat.

Application information

Substrate

Suitable substrates:

  • cured, sound original or old paint finishes that have been sanded
  • primed and filled plastic parts


Note

For plastic parts, see system information "The VW/Audi Paint System for Plastic Parts" (Information Sheet 5.74).

Pretreatment of substrates:

- Clean thoroughly with silicone remover -LVM 020 000 A5- or long-acting silicone remover -LVM 020 100 A5-.

VW UP. Allgemeine Informationen Lack

- Then sand.

VW UP. Allgemeine Informationen Lack

- Use a suitable cleaner before overcoating to ensure a clean, residue-free surface.

Processing

Usable products:

  • 2K HS topcoat
  • 2K VHS hardener -LHA 009 051 A2-/-LVM 009 051 A5-
  • 2K VHS hardener, long -LHA 009 052 A2-/-LHA 009 052 A3-
  • 2K VHS hardener, extra long -LHA 009 053 A2-
  • see application information 2K VHS hardener

Matting table:

VW UP. Allgemeine Informationen Lack


Mixing ratio

Hardening of the matting mixture:

Mixing ratio 4:1 by volume with:

  • 2K VHS hardener -LHA 009 051 A2-/-LVM 009 051 A5- (for small to medium areas, at medium temperatures)
  • 2K VHS hardener, long -LHA 009 052 A2-/-LHA 009 052 A3- (for larger areas at medium temperatures)
  • 2K VHS hardener, extra long -LHA 009 053 A2- (for large areas and high temperatures)
  • see application information 2K VHS hardener

Thinnable with:

  • 2K thinner -LVE 009 001 A5-
  • 2K thinner, special -LVM 009 200 A2/A5-
  • 2K thinner, long -LVM 009 300 A2-
VW UP. Allgemeine Informationen Lack

Processing/pot life:

- Ready-to-spray after 60-90 minutes at +20 °C

VW UP. Allgemeine Informationen Lack

Application method "Spray pass"

VW UP. Allgemeine Informationen Lack

- Application viscosity at +20 °C material temperature

Application viscosity "Compliant" and "HVLP":

18-20 seconds

VW UP. Allgemeine Informationen Lack

- 15 % thinner addition at +20 ºC material temperature

VW UP. Allgemeine Informationen Lack

- Set spray nozzle (see manufacturer's specifications): "Compliant" 1.3–1.4 mm.

- Set spray nozzle (see manufacturer's specifications): "HVLP" 1.3–1.4 mm.

- Set spray pressure (see manufacturer's specifications): "Compliant" 2.0–2.5 bar.

- Set atomizing air pressure (see manufacturer's specifications): "HVLP" 0.7 bar.

VW UP. Allgemeine Informationen Lack

- To achieve the recommended dry film thickness of 50-60 µm, 2 spray passes with a flash-off time in between are required.


Note

  • Addition of elasticizer -ALZ 011 001- is not required.
  • Matting component -ALN 775 106- is not suitable for matting clearcoats.
  • Matting component -ALN 775 106- is thixotropic; vigorous stirring makes the material flow. If necessary, use a shaker or shake the can by hand. Also, stir the material in the mixing system for 15 min. before use.
  • Adding the matting component may affect hiding power.
  • The gloss level actually achieved is influenced by color-dependent differences and various other factors. The following comparison shows some further parameters and their effect on the gloss level.
VW UP. Allgemeine Informationen Lack


Factors influencing gloss level:

  • Using different hardeners, thinners, application methods, drying conditions and film thicknesses leads to different gloss levels (up to 20 %).

Drying

Air drying at +20 ºC room temperature:

  • dust-dry after 30-50 minutes
  • ready for assembly after 5-6 hours
  • dry overnight
VW UP. Allgemeine Informationen Lack

The final flash-off time with forced drying is at least 5-10 minutes.

VW UP. Allgemeine Informationen Lack

Forced drying at +60 °C object temperature 30-40 minutes

VW UP. Allgemeine Informationen Lack

The final flash-off time with infrared drying is at least 5-10 minutes.

VW UP. Allgemeine Informationen Lack

Infrared drying with short-wave emitters: 5 minutes at 50 % output and 10 minutes at 100 % output

VW UP. Allgemeine Informationen Lack

Personal protective equipment:

  • Observe the safety data sheet
  • Wear personal protective equipment during application

Characteristics

VW UP. Allgemeine Informationen Lack


Storage

Guaranteed storage stability is 48 months from the date of production. Use no later than the date stated on the label when stored in sealed original containers at +20 °C.

VW UP. Allgemeine Informationen Lack

Matting component -LVM 769 810 A2-

Designation:

  • Matting component -LVM 769 810 A2-

Product description

Matting component -LVM 769 810 A2- produces a matte topcoat finish on metallic and plastic paint jobs when combined with 2K HS clearcoat and 2K HS topcoat.

Areas of use are larger surfaces/complete paint jobs as well as small and attached parts.

Application information

Substrate

Suitable substrates:

  • cured, sound original or old paint finishes that have been sanded
  • primed and filled metal and plastic parts


Note

For plastic parts, see system information "The VW/Audi Paint System for Plastic Parts" (Information Sheet 5.74).

Processing

Usable products:

  • 2K HS clearcoat -L2K 769 500 A5-
  • 2K HS Vario clearcoat -L2K 769 K01 A2-
  • 2K HS Optimum Plus clearcoat -LZK 769 K07 A5-
  • 2K HS Brillant Plus clearcoat -LZK 769 K05 A5-
  • 2K HS Performance Clearcoat -LZK 769 K06 A5-
  • 2K HS mixing clearcoat/topcoat -L2K 074/073...-
  • 2K HS hardener, long -LHA 009 047 A3-
  • 2K HS hardener, extra long -LHA 009 048 A3-
  • 2K VHS hardener, long -LHA 009 052 A2-/-LHA 009 052 A3-
  • 2K VHS hardener, extra long -LHA 009 053 A2-
  • see technical application information for hardener
  • 2K thinner -LVE 009 001 A5-
  • 2K thinner, long -LVM 009 300 A2-
  • 2K thinner, special -LVM 009 200 A2-/-LVM 009 200 A5-
  • Clearcoat additive -LVM 007 000 A2-

Gloss level setting/matting and processing notes


Note

See System Information 5.75 Gloss Level Setting of 2K HS Clearcoats and 2K HS Topcoats and System Information 5.76 Repair Paint System for Matte-Finish Vehicles.

Processing Notes


Note

  • Addition of elasticizer -ALZ 011 001- is not required.
  • Stir or shake matting component -LVM 769 810 A2- thoroughly in the can.
  • Mix matting component -LVM 769 810 A2- with 2K HS clearcoat and 2K HS topcoat as specified, and only prepare the sprayable mixture with hardener and thinner immediately before use. Spray the mixture without delay. If the mixture stands for a longer time (15 min.) in the mixing cup or spray gun cup, it must be stirred thoroughly again before further use (settling behavior).
  • Adding the matting component may affect hiding power.
  • It is essential to prepare test panels for the respective mixture in order to match the gloss level of the vehicle. Gloss measurements (60º measuring angle) on adjacent parts can also be helpful.
  • Blend repair or refinishing of the matt clear coat within the area, e.g. side panel or Clever-Repair, is not possible.
  • Dust inclusions cannot be polished out, so maintain extreme cleanliness throughout the entire painting process.
  • The gloss level actually achieved is influenced by color-dependent differences and various other factors. The following comparison shows some further parameters and their effect on the gloss level.

Factors influencing gloss level:

  • Using different hardeners, thinners, application methods, drying conditions and film thicknesses leads to different gloss levels (up to 20 %).

Drying

The final flash-off time with forced drying is at least 15-20 minutes.

VW UP. Allgemeine Informationen Lack

Forced drying at +60-65 ºC object temperature for 45 minutes

VW UP. Allgemeine Informationen Lack

Personal protective equipment:

  • Observe the safety data sheet
  • Wear personal protective equipment during application

Characteristics

VW UP. Allgemeine Informationen Lack


Storage

Guaranteed storage stability is 48 months from the date of production. Use no later than the date stated on the label when stored in sealed original containers at +20 °C.

VW UP. Allgemeine Informationen Lack

Texture component

Designation:

  • Texture component, fine -ALN 775 108-

Product description

Texture component, fine -ALN 775 108- is a component for 2K HS topcoat and converts it into a textured topcoat.

The topcoat can be used for plastic paint jobs on vehicles.

Application information

Substrate

Suitable substrates:

  • cured, sound original or old paint finishes that have been sanded
  • primed and filled plastic parts


Note

For plastic parts, see system information "The VW/Audi Paint System for Plastic Parts" (Information Sheet 5.74).

Pretreatment of substrates:

- Clean thoroughly with silicone remover -LVM 020 000 A5- or long-acting silicone remover -LVM 020 100 A5-.

VW UP. Allgemeine Informationen Lack

- Dry sand with a dual-action sander and dust extraction, P 400-500.

VW UP. Allgemeine Informationen Lack

- Or wet sand with P 800 grit abrasive paper.

VW UP. Allgemeine Informationen Lack

- Use a suitable cleaner before overcoating to ensure a clean, residue-free surface.

Processing

VW UP. Allgemeine Informationen Lack

Mixing ratio

Mixing ratio 1:1 by volume with 2K HS topcoat:

- Then cross-link this mixture 4:1 by volume with a suitable 2K VHS hardener.

See technical application information for 2K VHS hardener.

Thinnable with:

  • 2K thinner, special -LVM 009 200 A2/A5-
  • 2K Thinner, long -LVM 009 300 A2-
VW UP. Allgemeine Informationen Lack

Processing/pot life:

- Ready-to-spray pot life 90-100 minutes at +20 ºC

VW UP. Allgemeine Informationen Lack

Application method "Spray pass"

VW UP. Allgemeine Informationen Lack

- Application viscosity 4 mm at +20 °C, DIN 53211

- Application viscosity at +20 ºC material temperature; for "Compliant" and "HVLP" this is the mixed viscosity.

VW UP. Allgemeine Informationen Lack

- 15 % thinner addition at +20 ºC material temperature

VW UP. Allgemeine Informationen Lack

- Set spray nozzle (see manufacturer's specifications): "Compliant" 1.3–1.4 mm.

- Set spray nozzle (see manufacturer's data): "HVLP" 1.3-1.5 mm.

- Set spray pressure (see manufacturer's specifications): "Compliant" 2.0–2.5 bar.

- Set atomizing air pressure (see manufacturer's specifications): "HVLP" 0.7 bar.

VW UP. Allgemeine Informationen Lack

- To achieve the recommended dry film thickness of 50-60 µm, 2 spray passes with a flash-off time (5-10 min.) in between are required.


Note

  • Addition of elasticizer -ALZ 011 001- is not required.
  • Texture component, fine -ALN 775 108- is only suitable for use on attached parts (e.g. bumpers, spoilers).
  • Different spray techniques and film thicknesses can produce different effect finishes.
  • Texture component, fine -ALN 775 108- is thixotropic; stirring makes the material flow.
VW UP. Allgemeine Informationen Lack

Drying

Air drying at +20 ºC room temperature:

  • dust-dry after 30-50 minutes
  • Assembly-ready after 4-6 hours
  • dry overnight
VW UP. Allgemeine Informationen Lack

The final flash-off time with forced drying is at least 5-10 minutes.

VW UP. Allgemeine Informationen Lack

Forced drying at +60 °C object temperature 30-40 minutes

VW UP. Allgemeine Informationen Lack

The final flash-off time with infrared drying is 5 minutes.

VW UP. Allgemeine Informationen Lack

Infrared drying with short-wave emitters 10-15 minutes and medium-wave emitters 15-20 minutes.

VW UP. Allgemeine Informationen Lack

Personal protective equipment:

  • Observe the safety data sheet
  • Wear personal protective equipment during application

Characteristics

VW UP. Allgemeine Informationen Lack


Storage

Guaranteed storage stability is 24 months from production date. Use by the date stated on the label at the latest when stored in sealed original containers at +20 °C.

VW UP. Allgemeine Informationen Lack

Aquaplus pre-spray additive

Designation:

  • Spray-in additive for Aquaplus -LVM 030 000 A2-


Note

The application and processing notes for the pre-spray additive for Aquaplus -LVM 030 000 A2- are described under "Aquaplus Pre-Spray System".

Aqua Premium System additive

Designation:

  • Additive for Aqua Premium -LVM 035 200 A2/A3-
  • Additive for Aqua Premium -LVM 035 300 A1-
  • Additive for Aqua Premium -LVM 035 300 A1/A3-/-LVM 035 301 A3-


Note

The application and processing notes for the Aqua Premium additives are described in the corresponding base component "Aqua Premium System".